• Composites Research
• /
• v.29 no.5
• /
• pp.231-235
• /
• 2016

In this study, integrated co-bonded panels with the same configuration of hat stiffeners were fabricated and measured for ply waviness phenomenon. Total specimens consisted of 2 types; 1) the general co-bonded panel and 2) the co-bonded panel with caul plate made of carbon epoxy composite materials. The first general co-bonded panel specimen exhibited that laminate thickness on the stiffener location area was much thicker than the non-stiffener area and, there was ply waviness with 0.61 mm height and 3.29 mm length. In the second co-bonded panel specimen, the reduced waviness with 0.22 mm height and 1.37 length resulted in more than 50% improvements, which is due to the uniform pressure distribution of co-bonded interface by caul plate.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.9
• /
• pp.1421-1426
• /
• 2005

The stationary point structures and relative energies between them as well as binding energies of $(CO)_2$ have been investigated at the CCSD(T) level using the correlation-consistent basis sets aug-cc-pVXZ(X=T,Q,5). It is found that while the equilibrium structure corresponds to the C-bonded T-shaped configuration with intermolecular distance of 4.4 $\AA$, there exists another minimum, slightly higher in energy ($\sim$10 $cm^{-1}$) than the global minimum, corresponding to the O-bonded T-shaped configuration with the intermolecular distance of 3.9 $\AA$. The CCSD(T) basis set limit binding energy of $(CO)_2$ is estimated to be 132 $cm^{-1}$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.10
• /
• pp.809-815
• /
• 2014

The co-bonded dissimilar composite under a wide range of temperature change shows thermal distortion due to the differences in thermal expansion characteristics of the composite materials. Analysis of the thermal expansion characteristics of each composite is required for the design of co-bonded dissimilar composite structure with considering the shape distortion during the manufacturing process. In this work, digital image correlation (DIC) technique is introduced for measuring the thermal distortion characteristics of co-bonded dissimilar composite specimen, carbon/epoxy and silica/phenolic. The thermal distortion of co-bonded dissimilar composite specimen is numerically estimated and compared with the experiments. The estimated results is successfully validated using the measured results.

• Korean Journal of Materials Research
• /
• v.3 no.2
• /
• pp.175-184
• /
• 1993

Abstract Co-and/or AI-added Nd-Fe-B-based magnetic alloys were fabricated by using vacuum induction melting frunace, and melt-spun ribbons were made of the magnetic alloys with single roll rapid quenching method. The variation of magnetic properties of the melt-spun ribbons as a function of Cuwheel velocity (Vs) were investigated. Bonded magnets were made of the optimally quenched ribbon fragments, and the magnetic properties of the melt-spun ribbons and the bonded magnets were studied, relating to the microstructure and crystalline structure. Cu-wheel surface velocity had a strong effect on the magnetic properties of the melt-spun ribbons, and the maximum properties were obtained around Vs =20m/sec. The optimally quenched ribbon had a cellura-type microstructure, in which fine N$d_2$F$e_14$B grains were surrounded by thin Nd-rich phase. In case of a 2.1at% AI-added melt-spun ribbon, the magnetic properties were as follows: iHc, Br, and (BH)max were 15.5KOe, 7.8KG and 8.5MGOe respectively. And resin bonded magnets were fabricated by mixing optimally quenched ribbon fragments with 2.5wt % polyamide resin, compacting and binding at room temperature. The iHc, Br and (BH)max of bonded magnet were lO.2KOe, 4.4KG and 3.3MGOe respectively. And hot-pressed magnets were made by pressing the overquenched ribbons at high temperature. The magnetic properties of hot-pressed magnets were better than those of bonded magnets, and when the holding time was 8 minutes, the iHc, Br, and (BH)max of the hot-pressed magnet were 1O.8KOe, 7.3KG and 8.0MGOe respectively. Domain structure was mainly maze pattern, which means that the easy magnetization axis could be aligned, and the domain width of the hot-pressed magnets was smaller than that of bonded magnets.

• Bulletin of the Korean Chemical Society
• /
• v.7 no.6
• /
• pp.413-421
• /
• 1986

Hydrocarbon solution of $Cp_2Zr(CH_3)Cl$ react rapidly with $Na_2Fe(CO)_4$ (1/2 equiv.) to yield $[Cp_2Zr(CH_3)]_2Fe(CO)_4$ and NaCl. The more soluble metal-metal bonded complex $[Cp_2ZrC_8H_{17}]_2Fe(CO)_2$ has also been prepared through the reaction of $Cp_2Zr(C_8H_{17})BF_4$ and $Na_2Fe(CO)_4 (1/2 equiv.). The complexes were characterized by IR, $^1H$ NMR, ^{13}C$ NMR, and elemental analysis. The infrared spectrum of $[Cp_2ZrR]_2Fe(CO)_4$ shows four bands, which is indicative of a cis-structure. The $^{13}C$ NMR spectrum provides evidence for the cis-structure.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.5
• /
• pp.676-680
• /
• 2004

Complexes M($C_7H_2NO_5)3H_2O{\cdot}H_2O{\cdot}0.25MeCN$ (M=Ni, Co) were crystallized from the reactions of $Ni(CH_3COO)_2{\cdot}4H_2O\;or\;Co(CH_3COO)_2{\cdot}2H_2O$ with KSCN and 2,6-dicarboxy-4-hydroxypyridine (chelidamic acid). The structures were characterized by X-ray crystallography. The crystal structures of 1 and 2 show a distorted octahedral coordination geometry around the M(II) ions, which are chelated by one nitrogen atom and two oxygen atoms of the chelidamic acid and three water molecules. Complexes 1 and 2 display the hydrogen-bonded 3D framework. The magnetic behavior of 2 exhibits antiferromagnetic interaction.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.7
• /
• pp.634-641
• /
• 1995

The metal-carbon σ-bond cluster complexes 1-Mn(CO)5-2-R-1,2-C2B10H10 (R=CH3 Ia, C6H5 Ib) have been prepared in good yields from readily available carboranyl lithium complexes, 1-Li+-2-R-1,2-C2B10H10- (R=CH3, C6H5), by direct reaction with (CO)5MnBr. These manganese metal complexes are rapidly converted to the corresponding manganese metal carbene complexes, 1-[(CO)4Mn=C(OCH3)(CH3)]-2-R-1,2-C2B10H10 (R=CH3 IIIa, C6H5 IIIb), via alkylation with methyllithium followed by O-methylation with CF3SO3CH3. The crystal structure of IIIb was determined by X-ray diffraction. Thus, complex IIIb crystallizes in the orthorhombic space group P212121 with cell parameters a=15.5537(5), b=19.0697(5), c=7.4286(3) Å, V=2203.4(1) Å3, and Z=4. Of the reflections measured a total of 3805 unique reflections with F2>3σ(F2) was used during subsequent structure refinement. Refinement converged to R1=0.053 and R2=0.091. Structural studies showed that the manganese atom had a slightly distorted pseudo-octahedral configuration about the metal center with the carbene and ortho-carborane occupying the equatorial plane cis-orientation to each other.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.2
• /
• pp.304-310
• /
• 2006

A typical honeycomb sandwich panel consists of two thin, high-strength facings bonded to a thick, light-weight core. Each component by itself is relatively weak and flexible, but when it combined in a sandwich panel they produce a structure that is stiff, strong, and lightweight. To prove the suitability the honeycomb sandwich structure with prepreg, the mechanical properties of the skin materials and honeycomb sandwich structure were evaluated with the static strength tests. Accordingly, the honeycomb sandwich structure made by autoclave process is available for a panel on LCD/PDP assembly line.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.12 s.255
• /
• pp.1196-1202
• /
• 2006

A MEMS methanol reformer was fabricated and its performance was evaluated in the present study. Catalytic steam reforming of methanol was selected because the process had been widely applied in macro scale reformers. Conventional Cu/ZnO catalyst that was prepared by co-precipitation method to give the highest coating quality was used. The reactor structure was made by bonding three layers of glass wafers. The internal structure of the wafer was fabricated by the wet-etching process that resulted in a high aspect ratio. The internal surface of the reactor was coated by catalyst and individual wafers were fusion-bonded to form the reactor structure. The internal volume of the microfabricated reactor was $0.3cm^3$ and the reactor produced exhaust gas with hydrogen concentration at 73%. The production rate of hydrogen was 4.16 ml/hr that could generate power of 350 mW in a typical PEM fuel cell.

• Journal of Magnetics
• /
• v.10 no.4
• /
• pp.137-141
• /
• 2005

We confirmed that the improvement in properties of magnetic tunnel junctions prepared by radical oxidation after thermal treatment was mostly resulted from the redistribution of oxygen at the $AIOx/Co_{90}Fe_{10}$ interface. The as-deposited Al oxide barrier was oxygen-deficient but most of it re-oxidized into $Al_2O_3$, the thermodynamically stable stoichiometric phase, through thermal treatment. As a result, the effective barrier height was increased from 1.52 eV to 2.27 eV. On the other hand, the effective barrier width was decreased from 8.2 ${\AA}$ to 7.5 ${\AA}$. X-ray absorption spectra of Fe and Co clearly showed that the oxygen in the CoFe layer diffused back into the Al barrier and thereby enriched the barrier to close to a stoichiometirc $Al_2O_3$ phase. The oxygen bonded with Co and Fe diffused back by 6.8 ${\AA}$ and 4.5 ${\AA}$ after thermal treatment, respectively. Our results confirm that controlling the chemical structures of the interface is important to improve the properties of magnetic tunnel junctions.