• 대한조선학회논문집
• /
• 제42권5호
• /
• pp.472-478
• /
• 2005

From a rapid cooling to a slow cooling in the actual cooling process in shipyards, the phase of steel becomes martensite, bainite, ferrite, and pearlite. In order to simulate the cooling process, heat transfer analysis was performed considering the effects of impinging water jet, film boiling, and radiation. From above simulation it is possible to find the cooling speed at the inherent strain region and volume percentage of all phases in that region. By the suggested method based on the precise material properties calculated from volume percentage of all phases, it will be possible to predict the plate deformations by line heating more precisely. It is verified by comparing with some experimental results that the present method is very effective and efficient.

• Corrosion Science and Technology
• /
• 제21권4호
• /
• pp.273-281
• /
• 2022

The effect of addition of Cu on the localized corrosion performance of aged duplex stainless steel in chloride media has yet to be explained in a consistent manner, and there is some controversy in the literature regarding the composition of stainless steel and the experimental conditions (pH, temperature, chloride concentration, etc.) used. In this work, the effect of the addition of Cu on the microstructure, hardness, and corrosion resistance of duplex stainless steel in an acidic chloride or high concentration sulfuric acid solutions was investigated for annealed and aged alloys. The Cu addition of annealed duplex stainless steel strengthened the alloy and reduced the ferrite contents of the alloy, and it also increased the polarization behavior in chloride or sulfuric solutions, except for the case of a high potential in acidic chloride solution. However, the Cu addition of aged duplex stainless steel reduced the formation of harmful phases such as sigma and kai and increased the polarization behavior in acidic chloride or sulfuric solutions up to 0.8 wt% of the Cu content, after which it slightly decreased at 0.8 wt% Cu or more.

• 한국전자파학회논문지
• /
• 제19권3호
• /
• pp.343-351
• /
• 2008

본 논문에서는 FPC(Flexible Printed Circuit) 케이블에 적층된 나선형 인덕터를 내장하여 다기능 케이블을 위한 공통 모드 필터를 제안하였다. 공통 모드 필터가 내장된 FPC 케이블은 별도의 SMD(Surface Mounted Device) 필터 없이 연성 케이블과 공통 모드 차단 특성을 가짐으로서, 다기능 케이블이라는 새로운 개념을 제시한다. 내장된 공통 모드 필터는 광대역의 공통 모드 차단 대역을 가지고 손실이 큰 페라이트와 같은 자성 물질을 사용하지 않아 차동 모드 삽입 손실 및 반사 손실이 향상되었다. 3-turn 인덕터를 가진 공통 모드 필터는 공통 모드차단 대역이 $0.4{\sim}3.12GHz$이며, 페라이트를 적용한 상용 LTCC(Low Temperature Co-fire Ceramic) 공통 모드 필터에 비해 3 GHz에서 1.95 dB, 8 GHz에서 6.97 dB의 향상된 차동 모드 삽입 손실을 갖는다.

• 대한전자공학회논문지TC
• /
• 제48권12호
• /
• pp.54-61
• /
• 2011

본 논문에서는 탐지영역에 존재하는 이동 표적의 탐지 정보를 제공하는 PDR(Pulsed Doppler Radar) 기반 USN 센서망에 적용 가능한 감시경보 시스템을 제안한다. 제안된 시스템은 센서에서 실측된 신호를 분석하여 얻어진 탐지영역과 작전 지역의 지형적 특성이 고려된 최적의 센서 배치를 사용한다. 본 논문에서 제안된 세 가지 배치형태는 격자형, 선형, 갈지자형 센서 배치이다. 또한, 제안된 배치를 기반으로 감시경보 시스템을 구현하여, 이동 표적과 지휘소와의 거리변화에 따른 경보등급을 인식-주의-경고-위험 순으로 조절하여 전탐사에게 시청각적 정보로 감시 수준을 알릴 수 있는 시스템을 개발하였다. 실제 외부실험을 통해 제안된 센서 배치를 사용한 감시경보 시스템의 성능을 검증하였다.

• 열처리공학회지
• /
• 제11권4호
• /
• pp.333-341
• /
• 1998

The study was investigated on the effect of austenitizing and austempering conditions on retained austenite amount and carbon contents in retained austenite and simultaneously the effect of these variation on hardness, tensile and impact properties. A material of as-cast condition is composed of bull's eye structure with ferrite surrounding spheroidized graphite having about $5-10{\mu}m$ size and matrix structure of pearlite. Then, the contents of spheroidized graphite was about 5%. The retained austenite and carbon contents in the retained austenite were increased with the increasing of austenitizing and austempering temperatures, while the retained austenite showed the peak value and is decreased with increasing of austempering time. With increasing of austenitizing temperature, tensile strength, elongation and impact absorb energy increased and hardness was almost not changed, while with increasing of austempering temperature, tensile strength and hardness decreased, whereas elongation and impact absorb energy was increased. With increasing of retained austenite amount, the tensile strength is slowly decreased but elongation was increased with direct proportion. Also, Impact absorb energy is shown identity value untile about 18%, but rapidly increased above it. Elongation and Impact absorb energy are strongly controlled by the amount of retained austenite, but tensile strength is affected with various factors such as retained austenite amount and bainitic morphology.

• Journal of electromagnetic engineering and science
• /
• 제11권3호
• /
• pp.166-173
• /
• 2011

In this paper, we implemented and analyzed a wireless power transfer (WPT) system with a CSPR topology. CSPR refers to constant current source, series resonance circuit topology of a transmitting coil, parallel resonance circuit topology of a receiving coil, and pure resistive loading. The transmitting coil is coupled by a magnetic field to the receiving coil without wire. Although the electromotive force (emf) is small (about 4.5V), the voltage on load resistor is 148V, because a parallel resonance scheme was adopted for the receiving coil. The implemented WPT system is designed to be able to transfer up to 1 kW power and can operate a LED TV. Before the implementation, the EMF reduction mechanism based on the use of ferrite and a metal shield box was confirmed by an EM simulation and we found that the EMF can be suppressed dramatically by using this shield. The operating frequency of the implemented WPT system is 30.7kHz and the air gap between two coils is 150mm. The power transferred to the load resistor is 147W and the real power transfer efficiency is 66.4 %.

• Advances in materials Research
• /
• 제4권4호
• /
• pp.215-226
• /
• 2015

Experiment on roughness and micro pit defects of SUS 430 ferrite stainless steel was investigated in laboratory. The relation between roughness and glossiness with reduction in height, roll surface roughness, emulsion parameters was analyzed. The surface morphology of micro pit defects was observed by SEM, and the effects of micro pit defects on rolling reduction, roll surface roughness, emulsion parameters, lubrication oil in deformation zone and work roll diameter were discussed. With the increasing of reduction ratio strip surface roughness Ra(s), Rp(s) and Rv(s) were decreasing along rolling and width direction, the drop value in rolling direction was faster than that in width direction. The roughness and glossiness were obtained under emulsion concentration 3% and 6%, temperature $55^{\circ}C$ and $63^{\circ}C$, roll surface roughness $Ra(r)=0.5{\mu}m$, $Ra(r)=0.7{\mu}m$ and $Ra(r)=1.0{\mu}m$. The glossiness was declined rapidly when the micro defects ratio was above 23%. With the pass number increasing, the micro pit defects were reduced, uneven peak was decreased and gently along rolling direction. The micro pit defects were increased with the roll surface roughness increase. The defects ratio was declined with larger gradient at pass number 1 to 3, but gentle slope at pass number 4 to 5. When work roll diameter was small, bite angle was increasing, lubrication oil in micro pit of deformation zone was decreased, micro defects were decreased, and glossiness value on the surface of strip was increased.

• 대한금속재료학회지
• /
• 제50권12호
• /
• pp.873-882
• /
• 2012

Dual Phase (DP) steel which has a soft ferrite phase and a hard martensite phase reveals both high strength and high ductility and has received increased attention for use in automotive applications. To conduct structural analysis to verify vehicle safety, highly credible experimental results are required. In this study, tensile tests were performed in a strain rate range from $10^{-4}/s$ to 300/s for Sink Roll-Less (SRL) hot-dip metal coated sheets. Collision properties were estimated through simulation by LS-DYNA using the stress-strain curve obtained from the tensile test. The simulation results were compared with the actual crash test results to confirm the credibility of the simulation. In addition, a tensile test and a crash test with 2% prestrain and a baking (PB) specimen were evaluated identically because automotive steel is used after forming and painting. The mechanical behaviors were improved with an increasing strain rate regardless of the PB treatment. Thus, plastic deformation with an appropriate strain rate is expected to result in better formability and crash characteristics than plastic deformation with a static strain rate. The ultimate tensile strength (UTS) and absorbed energy up to 10% strain were improved even though the total elongation decreased after PB treatment, The results of the experimental crash test and computer simulation were slightly different but generally, a similar propensity was seen.

• 항공우주시스템공학회지
• /
• 제17권1호
• /
• pp.42-50
• /
• 2023

본 연구에서는 SrZn_2-xCo_xFe₁₆O₂₇ 화학식을 갖는 육방정 구조의 페라이트 분말을 고상법으로 합성하고 Co-Zn 함량 변화에 따른 전자기파 흡수 특성을 0.1-18 GHz의 주파수 범위와 0 ~ 10 mm 흡수체 두께 범위에서 평가하였다. 흡수체 두께에 따른 전자기파 흡수 특성은 고주파 복소 투자율과 유전율 측정 data로부터 전송선 이론을 기반으로 계산을 통해 반사손실 (RL)을 도출하였으며, 일부 시료에 대해서는 RL 실측정을 통해 계산된 결과와 잘 맞는 것을 보였다. Co의 치환량 (x)에 따라 고주파 복소 투자율 특성이 변화하였으며 이에 따라 전자기파 흡수 주파수 대역의 조절이 가능하였다. 또한 x = 1.0, 1.25, 1.5 시료에서는 매우 우수한 최대 전자기파 흡수 특성 (RL = -70 ~ -50 dB )을 보이며, 90% 이상의 전자기파 에너지를 흡수 (RL ≤ -10 dB) 하는 주파수 밴드 폭 또한 10 GHz 이상으로 광대역 레이다 흡수가 가능함을 보였다.

• 한국세라믹학회지
• /
• 제39권8호
• /
• pp.789-794
• /
• 2002

본 연구에서는 TMS[Tetramethylsilane:$Si(CH_3)_4$], $NH_3$와 $H2$를 이용하여 나노크기의 Si-C-N precursor 분말을 합성하기 위하여 CVC법을 이용하였으며 반응온도, TMS/$NH_3$ 비 그리고 TMS/$H_2$ 비를 변화시켰다. XRD와 FESEM 분석을 통해서 결정상과 입자의 크기 그리고 입자의 형태를 관찰하고자 하였으며, 그 결과 제조된 분말은 모든 실험 조건하에서 87∼130 nm 크기를 지닌 균일한 구형의 비정질 분말이 얻어졌다. 입자 크기는 반응온도의 감소에 따라 감소하였으며, 또한 TMS/$NH_3$, TMS/$H_2$ 비가 작아질수록 감소하였다. EA 분석 결과 제조된 분말은 Si, N, C, H로 이루어졌음을 알 수 있었으며 FT-IR를 통하여 Si-N, C-N, Si-C 결합을 가진 Si-C-N precursor 분말이 제조되었다.