• Journal of Drive and Control
• /
• v.13 no.1
• /
• pp.34-42
• /
• 2016

This study studied how the clearance, overlap and mismatch errors of spool-sleeve affect the static pressure characteristics of a servo valve. A computer simulation model was established as a direct acting servo valve and a series of simulations was conducted for various values of clearance, overlap and mismatch errors. Pressure gain decreased as the clearance increased. The overlap also affects the pressure gain and was similar to the effect of clearance. Asymmetry of the pressure plot got worse and worse as the mismatch error increased.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.5
• /
• pp.1508-1515
• /
• 1996

The method of utilizing sensitivity linkages for the analysis of mechanical errors are proposed. As sources of the mechanical error, tolerances in the link length and clearances in thejoints are considered. It is demonstrated that the problem of calculating mechanical errors of a 4-bar mechanism can be transformed into a problem of conventeional velocity analysis of a sensitivity linkage. As a result of the present study, it is found and proved that the mechanical error of the output angle in the 4-Bar mechaism is represented as a simple harmonic function with respect to the relative position of the pin on the clearance circle. Also the vector representing the mechanical error of a coupler point makes, in general, an ellipse as the relative angle varies on the clearance circle. With these results we can better identify the characteristic of the mechanical errors in linkages.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.2
• /
• pp.184-191
• /
• 2003

A parallel manipulator has high stiffness and all the joint errors on the device are not accumulated at the end -effector unlike a serial manipulator. These are the reasons why the parallel manipulator has been widely used in many fields of industry. In the parallel manipulator, it is very important to predict the exact pose of the end-effector when we want to control the end-effector motion. Installation errors have to be determined in order to predict and control the actual position and pose of the end-effector. This paper presents an algorithm to find the whole 36 joint error components with joint clearance errors and measurement errors considered, when a link length measurement sensor is used and data more than 36 times are acquired for 36 different configurations. A simulation test using this algorithm is performed with a Matlab program which uses the Levenberg-Marquardt method that is known to be efficient for non-linear optimization.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.187-190
• /
• 2002

In this paper, we deal with performance improvement of OBE for automatic gate clearance system by using DSRC network of 5.8GHz ISM band. A data format is improved to represent Rx and Tx information which is need to perform clearance at the gate of container terminal. An error message caused by data discordance is added to Previous data format. A graphic LCD monitor is used to control a character font and use Korean.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.2
• /
• pp.327-336
• /
• 1997

This paper addresses an analytical approach to the mechanical error analysis and tolerance design of a four-bar path generator with lubricated joints. The mobility method is applied to consider lubrication effects and the four-bar path generator is stochastically modeled by using the clearance vector model for methanical error analysis. To show the validity of the proposed method, the mechanical errors obtained by applying the method to a four-bar path generator are compared with those by Monte Carlo simulation. Based on this analytical method, an optimal tolerance design problem is formulated and solved for the four-bar path generator.

• Journal of KSNVE
• /
• v.11 no.1
• /
• pp.125-131
• /
• 2001

There is a clearance between the parts of a machine due to design tolerance, manufacturing error, wear, looseness, or misalignment. If the clearance is large, the vibration and noise of the machine is generally large. Therefore, the analysis on the nitration and noise of a machine can tell the clearance of the machine, which reveals the condition of the machine, i.e., the existence of faults and the safety of the machine. The investigation of this kind of research should be on the basis of experimental results. A link mechanism with a clearance at a joint between the coupler and locker is made for the investigation of the condition monitoring of a machine due to clearance. The vibration and sound are measured from the link driving system during the operation. The signals are clarified using line enhancement technique. The noise removed signals are used to develop the dynamic model of the system for a model based fault diagnosis. Also this study showed that the clarified signals can be used for the calculation of the joint forces between the coupler and rocker and for the correlation between the vibration and sound levels and the clearance sizes.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.303-304
• /
• 2002

This paper presents theoretical analysis of the NRRO(the non-repeatable run-out) for a ball bearing with geometric imperfection. This imperfection contains ball size error, ball waviness, outer race waviness and inner race waviness. The 3D dynamic analysis of a ball bearing using the Newton-Raphson method is performed to calculate the displacement of shaft center. The radial and axial NRRO are simulated, and preload and clearance effects are investigated. Preload and clearance have significant effects on radial and axial NRRO of for miniature ball bearings.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.672-675
• /
• 2000

There are many sources of errors in the parallel device. This study investigates the effect of a clearance error at a U-joint on the position and orientation errors of the platform of a new parallel device, cubic parallel manipulator. In this study, the limits of errors can be estimated for given conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.2
• /
• pp.351-358
• /
• 1994

A probabilistic model and analysis methods to determine the means and variances of the velocity and acceleration in stochastically-defined planar pin jointed kinematic chains are presented. The presented model considers the effect of tolerances on link length and radial clearance and uncertainty of pin location as a net effect on the link's effective length. The determination of the mean values and variances of the output variables requires the calculation of sensitivities of secondary variables with respect to the random variables. It is shown that this computation is straightforward and can be accomplished by a conventional kinematic analysis package with minor modification. Thus, the concepts of tolerance and clearance have been captured by the model and analysis. The only input data are the nominal linkage model and statistical information. The "effective link length" model is shown to be applicable to both analytical solution and Monte Carlo simulation. The results from both methods are compared. This paper Ksolves the higher-order kinematic problems for the probabilistic design analysis of stochastically-defined mechanisms.echanisms.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.2
• /
• pp.191-198
• /
• 2015

In this study, the flow characteristics at the ventilation holes was analyzed by using numerical method when carbon composite brake disk was rotated at a constant speed. In order to ensure the validity of the analysis results, grid dependency test was performed by considering the accuracy and appropriateness, and 4mm mesh size was selected for decrease of the maximum error rate 63.6%. As a result, the outside air flows in the clearance between the disk and shaft in case of B model. whereas, the outside air flows in the clearance or the outlet of the ventilation holes in case of A and C models. And also average static pressure at the outlet was changed depending on shape of the ventilation holes and rotational speed of the disk in case of A and C models. Besides, in the B model, intake air according to the clearance goes with side surface of ventilation hole, and so increased by mean velocity of 4.64m/s and mean pressure of 0.58pa in the ventilation hole outlet, in case of disk rotational speed of 146.21rad/s.