• Biotechnology and Bioprocess Engineering:BBE
• /
• v.11 no.6
• /
• pp.471-476
• /
• 2006

Pseudomonas aeruginosa F722 produces a biosurfactant (BS) during its degradation of carbon and hydrocarbon compounds. The culture conditions for upgrading the biosurfactant productivity were investigated. The concentration of the biosurfactant produced by P. aeruginosa F722 was 0.78 g/L in C-medium; however, this increased to 1.66 g/L in BS medium, which was experimentally adjusted to optimal conditions. $NaNO_{2}$ was found to be most effective for microbial growth, with an $O.D_{600nm}$ of 1.18 for 0.1 % $NaNO_{2}$. Microbial growths, according to the $O.D_{600nm}$ were 2.53, 2.68, 2.89, and 2.87 for glucose, glycerol, $n-C_{10},\;and\;n-C_{22}$, respectively. Clear zone diameters (cm), indicating biosurfactant activity, were 9.0, 8.8, 5.7, and 8.5 for glucose, glycerol, $n-C_{10},\;and\;n-C_{22}$, respectively. Microbial growth was not consistent with the biosurfactant activity. The best biosurfactant activity was found with a C/N ratio of 20. Under optimal culture condition, the average surface tension decreased from 70 to 30 mN/m after 5 days. With aeration of 1.0 vvm, the biosurfactant produced increased to 1.94 g/L (up to 20%) compared to that of 1.66 g/L with no aeration. With aeration, the velocities of glucose degradation during both the log and stationary growth phases increased from 0.25 and $0.18\;h^{-1}$ to 0.33 and $0.29\;h^{-1}$, respectively, and the time for the culture to arrive at the maximum clear zone diameter became shorter, from 80 down to 60 h with no aeration.

• Korean journal of food and cookery science
• /
• v.15 no.4
• /
• pp.410-417
• /
• 1999

Antimicrobial activity of Plantain(Plantago asiatica L.) was investigated. Methanol extract of dried Plantain was fractionated to hexane, chloroform, ethylacetate, butanol and aqueous fraction. Ethylacetate fraction among these fractions showed the highest inhibitory effect on the microorganisms such as B. subtilis, E. coli, and V. parahaemolyticus at 500 $\mu\textrm{g}$/disc. Ethylacetate fraction was further fractionated into 8 fractions by silica gel column and thin layer chromatography(TLC). The results showed that ethylacetate fractions No. 2 and 3 had the highest anti-microbial activity. They were mixed again, re-separated, and seven fractions were obtained. Among them, No.4 and 6 fraction had the highest inhibitory effect on the microorganisms, which were then separated into four fractions. In the 3rd fractionation, No.4 fraction was identified as hexadecanoic acid by HPLC, $^1$H-NMR and GC-MS.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.6
• /
• pp.605-614
• /
• 2022

In this study, oregano was extracted by supercritical extraction and hydrothermal extraction method. In vitro experiments such as antimicrobial and antioxidant activity test were performed. As a result of the disc diffusion method, only the supercritical extracts formed a clear zone. The MIC for S. aureus was found only in the supercritical fluid extracts and it was 1000 ㎍/mL. The hydrothermal extract's MIC is 125 ㎍/mL for C. acnes. Through biofilm inhibition assay, we found that the supercritical fluid oregano extracts inhibit the biofilm of S. aureus by more than 70% even at low concentrations of 125 ㎍/mL. On the other hand, the antioxidant ability of the hydrothermal extract was better than that of the supercritical fluid extracts. Furthermore, we tried to make a skincare ingredient for atopic dermatitis by utilizing the S. aureus biofilm inhibitory ability of oregano supercritical fluid extracts. Liposome was used to overcome the low solubility of the oregano supercritical fluid extracts and increase stability.

• Journal of the Korean Society of Food Culture
• /
• v.20 no.6
• /
• pp.709-714
• /
• 2005

Antibacterial activities of the freeze-dried bamboo sap dissolved into the water or 50% ethanol were determined and antimicrobial activity of bamboo sap dissolved into distilled water was most strong with 15 mm of the diameter of inhibiting clear zone against Listeria monocytogenes ATCC 19114 among gram positive bacteria tested, but it did not inhibit Bacillus subtilis ATCC 6633 at all, and the sap was most greatly inhibited the growth of Shigella dysenteriae ATCC 9361 among gram negative bacteria with 15 mm of the diameter of inhibiting clear zone. Bamboo sap dissolved into 50% ethanol most strongly inhibited the growth of L. monocytogenes ATCC 19114 and it also inhibited the growth of B. subtilis ATCC 6633 which did not show any with the sap dissolved into distilled water. The sap dissolved into 50% ethanol was most greatly inhibited the growth of S. dysenteriae ATCC 9361 among gram negative bacteria with 23 mm of the diameter of inhibiting clear zone, and it inhibited Vibrio parahaemolyticus WSDH 22, Vibrio vulnilicus ATCC 29307 and Escherichia coli O157 WSDH 54 with 16 mm of the diameter of inhibiting clear zone. However, Both of the saps dissolved in distilled water and 50% ethanol did not showed any inhibition against the lactic acid bacteria of Lactobacillus plantarum KCTC and Lactobacillus brevis KCTC. Most of the tested bacteria were more sensitive to the sap dissolved in 50% ethanol than the sap dissolved in distilled water. The lowest minimum inhibitory concentration of the bamboo sap dissolved into 50% ethanol was 0.6 mg eq./disc with L. monocytogenes ATCC 19114, but that of the sap dissolved into distilled water was 0.8 mg eq./disc with Staphylococcus epidermides ATCC 12228, S. dysenteriae ATCC 9361, L. monocytogenes ATCC 19114, Salmonella typhimurium WSU 2380 and V. parahaemolyticus WSDH 22. In a model food system of the sterilized chocolate milk, antibacterial activities of the sap dissolved into 50% ethanol were relatively stronger than those of the sap dissolved into distilled water and the activities against the bacteria tested were very similar each other. These result suggested the bamboo sap can be used as a natural food preservative.

• The Journal of the Convergence on Culture Technology
• /
• v.5 no.3
• /
• pp.271-282
• /
• 2019

This study was conducted to evaluate physiological activity of Robinia pseudo-acacia leaf and its skin penetration using polymer micelles and skin penetrating peptide. After extraction with Robinia pseudo-acacia using the ethanol and distilled water, various physiological activities were examined. The total concentration of polyphenol compounds was determined to be 47.42 mg/g (ethanol extract), 56.88 mg/g (hydrothermal extract) and DPPH radical scavenging ability at $1,000{\mu}g/mL$ was 44.24% in ethanol extract and it is higher than value(41.50%) in hydrothermal extract. The elastase inhibitory assay showed concentration dependence and elastase inhibition of Robinia pseudo acacia leaf ethanol extract was 54.09%, which was the highest at $500{\mu}g/mL$. In the SOD-like experiments, the concentration-dependent results were showed and the SOD-like activity of the Robinia pseudo-acacia leaf ethanol extract was higher than that of the Robinia pseudo acacia leaf hydrothermal extract at all concentrations. At a concentration of $500{\mu}g/mL$, Robinia pseudo acacia leaf ethanol extract showed the highest SOD-like activity of 76.41%. The tyrosinase inhibition at $20{\mu}g/mL$ was determined to be 56.47% (ethanol extract), 23.05% (hydrothermal extract). In the antimicrobial experiments, the hydrothermal extract had no effect, but ethanol extract represented maximum clear zone of 11.00 mm in Propionbacterium acnes strain and maximum clear zone of 10.50 mm. in Bacillus subtilis strain. To solve the problem of insolubility and to improve skin penetration, PCL-PEG polymer micelles containing Robinia pseudo-acacia leaf ethanol extracts and 1.0% cell permeable peptide, hexa-D-arginine (R6) were successfully prepared with particle size of 108.23 and 126.47 nm and excellent skin permeation effects could be showed.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.639-643
• /
• 2002

The main purpose of this study was to investigate the formation mechanisms of imperfections such as irregular humps, outer cavity and inner cavity in the laser fusion zone of diamond saw blade. Laser beam welding was conducted to join two parts of blade; mild steel shank and Fe-Co-Ni sintered tip. The variables were beam power and travel speed. The microstructure and elements distributions of specimens were analyzed with SEM, AES, EPMA and so on. It was found that these imperfections were responded to heat input. Irregular humps were reduced in 10.4∼17.6kJ/m heat input range. However there were no clear evidences, which could explain the relations between humps formation and heat input. The number of outer cavity and inner cavity decreased as heat input was increased. Considering both possible defects formations mechanisms, it could be thought that outer cavity was caused by insufficient refill of keyhole, which was from rapid solidification of molten metal and fast molten metal flow to the rear keyhole wall at low heat input. More inner cavities were found near the interface of the fusion zone and sintered segment and in the bottom of the fusion zone. Inner cavity was mainly formed in the upper fusion zone at high heat input whereas was in the bottom at low heat input. Inner cavity was from trapping of coarsened preexist pores in the sintered tip and metal vapor due to rapid solidification of molten metal before the bubbles escaped.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.2 no.1 s.2
• /
• pp.53-62
• /
• 2003

This paper demonstrates the in-vehicle dilemma zone warning system (DZWS) project developed as a part of the Driver Advisory and Collision Warning System in Automated Vehicle and Highway System (AVHS). The DZWS project, one of the Korea national ITS projects in 2000 develops the in-vehicle warning device to support drivers' decision making on whether to stop or to proceed to clear the intersection prior to the onset of yellow signal for avoiding the high risk of collision at signalized intersections through the dedicated short range communication (DSRC). This paper explores the design of optimal communication systems between roadway and vehicles, the operational and functional concepts of dilemma zone warning system based on appropriate approach speeds, and the system integration for field test at two sites of signalized intersections. Findings from the system integration indicated that the system would be implemented in eliminating the dilemma zone relative to approach speeds and in reducing red light violations and intersection collisions through the in-vehicle warning device at signalized intersection.

• Economic and Environmental Geology
• /
• v.16 no.1
• /
• pp.11-18
• /
• 1983

Gyeongsang Basin in the southeastern part of the Korean peninsular is characterized by many fault systems. To decipher the geotectonical evolution of the Korean peninsular and marginal basins in her adjacent areas it is prerequisite to understand the spatial distribution pattern and mutual relationships of these fault systems. Because of difficulties in finding any criterion to recognize the faults in field, their extension and mutual relationships in ages are not very clear yet. As an attempt to find geophysical criteria to recognize the fault, geoelectrical resistivity survey was carried out in this study. With the Wenner configuration four resistivity soundings and twenty seven resistivity profilings were done. The electrode distance used was up to 50m. From the results of the resistivity soundings and boring data of earlier groundwater investigations the depth of alluvial and weathered zone was established to be at most 20m in the study area. In the resistivity profiling low resistivity anomaly zones are detected on every traverse, which are interpreted as caused by fractures, fault clays and mylonites in the fault zone. The width of the fault zone amounts to 0.3-1km. By correlating and connecting the negative anomaly zones from traverse to traverse one can determine the trend of th of the faultzone and therefore that of fault itself. The recognized fault trend in this way was $N15^{\circ}-20^{\circ}E$ and this coincides with the direction of the inferred fault line from earlier geological surface mapping. With the help of this characteristical negative anomaly the existance of another $N80^{\circ}W$ trending fault was estabished. This study has shown that geoelectrical resistivity survey can be applied successfully to the problem of tracing fault line insofar as a fault zone has been developed along fault line.

• Economic and Environmental Geology
• /
• v.14 no.2
• /
• pp.55-76
• /
• 1981

Southwestern contact zone of the Boeun granodiorite occurs near the thrust fault between the Ogcheon Group and Majeonri Limestone Formation. Ogcheon Group, metasediments composed of the Munjuri Formation, Changri Formation, and unconformably overlying Hwanggangri Formation, belongs to greenschist facies of regional metamorphism accompanied with deformation of two fold axes, $N10^{\circ}E$ and $N45-65^{\circ}E$ directions. Basic metamorphic rocks occurring in the Changri and Limestone Formations are the meta-basalts and meta-diabases of tholeiitic basalt series. The meta-basalts intruded in the Changri Formation as sills, whereas the meta-diabases in the Changri and Limestone Formations as stocks in appearance. They are considered to have emplaced before the formation of two fold axes and related with the thrust fault, based on the geologic setting of the area. The metamorphic facies are identified to be greenschist facies to epidote-amphibolite facies for the meta-basalt, and epidote-amphibolite facies for the meta-diabases. It is interpreted that such a variety of facies was related from the combination of earlier deuteric alteration and later regional metamorphism. The metasediments in southwestern contact zont of the Boeun granodiorite which is a product of later syntectonic intrusion of middle Jurassic in age, show pyroxene-hornfels facies near the contact and amphibole-horenfels facies away from the contact to the mineral zoning in the contact metamorphic aureole of the Limestone Formation, based on the paragenetic analysis of mineral assemblages. The Limestone in the area appears to be considerably $SiO_2-CaO-MgO-CO_2-H_2O$ can be adopted to evaluate equilibrium conditions of the mineral assemblages in each mineral zone. It is revealed that a temperature gradient was existed accross the contact aureole ranging from the higher igneous side to lower sedimentary side, whereas no clear trend of $XCO_2$ variation appears but high mole fraction. The tremolite diopside-quartz-calcite assemblages occurs in common through the most mineral zones of contact aureole that is in good agreement with the equivalent reaction curve which extends over a wide range of $T-XCO_2$ conditions.

• Journal of Agricultural Extension & Community Development
• /
• v.17 no.4
• /
• pp.799-825
• /
• 2010

The purpose of the present study is to provide policy implications for successful development of the metropolitan economic zone in Korea followed by in-depth case studies on the US Metropolitan Economic Region. This study looked into diverse experiences of the US mega regions investigating their key strategies, requirements and standards, etc. Urban areas in the US are designated based on CBSA, a standard for statistical area since 1950. The US has a clear standard to define rural and suburban area and is trying to reflect urban structural changes including suburbanization. The US annexation system is relatively simple to operate. Furthermore, the system helps the growth of rural areas by gradually incorporating rural areas into urban areas. We found that action plans of the US mega regions facilitate strategic growth and development for balanced territorial development, incorporating multi-dimensional and comprehensive approaches. We also found that the US mega regions are designated with regard to the local natures. Couple of policy implications were extracted from the US experiences. First, since the construction of mega regions in Korea concerns less on the inter-regional connections with other regions, we need to incorporate diverse standards to divide the regions with respect to the spatial and local characteristics. Second, local governments should collaborate with each other for successful economic development of the metropolitan economic zones. Administrative districts renovation can be a immediate and effective solution to facilitate the collaboration. We recommended to consider consolidating administrative areas to construct successful metropolitan economic zones.