• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.6
• /
• pp.511-518
• /
• 2013

Steam Generator (SG) tube, as a barrier isolating the primary coolant system from the secondary side of nuclear power plants (NPP), must maintain the structural integrity for the public safety and their efficient power generation. So, SG tubes are subject to the periodic examination and the repairs if needed so that any defective tubes are not in service. Recently, corrosion related degradations were detected in the tubes of the domestic OPR-1000 NPP, as a form of axially oriented outer diameter stress corrosion cracking (ODSCC). According to the studies on the factors causing the heat fouling as well as developing corrosion cracking, densely scaled deposits on the secondary side of the SG tubes are mainly known to be problematic causing the adverse impacts against the soundness of the SG tubes [1]. Therefore, the processes of various cleaning methods efficiently to dissolve and remove the deposits have been applied as well as it is imperative to maintain the structural integrity of the tubes after exposing to the cleaning agent. So qualification test (QT) should be carried out to assess the perfection of the chemical cleaning and QT is to apply the processes and to do ECT. In this paper, the chemical cleaning processes to dissolve and remove the scaled deposits are introduced and results of ECT on the artificial crack specimens to determine the effectiveness of those processes are represented.

• The Journal of Advanced Prosthodontics
• /
• v.7 no.2
• /
• pp.85-92
• /
• 2015

PURPOSE. This study aimed to investigate the efficacy of cleaning solutions on saliva-contaminated zirconia in comparison to air-abrasion in terms of resin bonding. MATERIALS AND METHODS. For saliva-contaminated air-abraded zirconia, seven cleaning methods)-no contamination (NC), water-spray rinsing (WS), additional air-abrasion (AA), and cleaning with four solutions (Ivoclean [IC]; 1.0 wt% sodium dodecyl sulfate [SDS], 1.0 wt% hydrogen peroxide [HP], and 1.0 wt% sodium hypochlorite [SHC])-were tested. The zirconia surfaces for each group were characterized using various analytical techniques. Three bonded resin (Panavia F 2.0) cylinders (bonding area: $4.5mm^2$) were made on one zirconia disk specimen using the Ultradent jig method [four disks (12 cylinders)/group; a total of 28 disks]. After 5,000 thermocycling, all specimens were subjected to a shear bond strength test with a crosshead speed of 1.0 mm/minute. The fractured surfaces were observed using an optical and scanning electron microscope (SEM). RESULTS. Contact angle measurements showed that groups NC, AA, IC, and SHC had hydrophilic surfaces. The X-ray photoelectron spectroscopy (XPS) analysis showed similar elemental distributions between group AA and groups IC and SHC. Groups IC and SHC showed statistically similar bond strengths to groups NC and AA (P>.05), but not groups SDS and HP (P<.05). For groups WS, SDS, and HP, blister-like bubble formations were observed on the surfaces under SEM. CONCLUSION. Within the limitations of this in vitro study, some of the cleaning solutions (IC or SHC) were effective in removing saliva contamination and enhancing the resin bond strength.

• Restorative Dentistry and Endodontics
• /
• v.42 no.2
• /
• pp.105-110
• /
• 2017

Objectives: This study investigated the cleaning ability of ultrasonically activated irrigation (UAI) and a novel activation system with reciprocating motion (EC, EasyClean, Easy Equipamentos $Odontol\acute{o}gicos$) when used with a relatively new chelating agent (QMix, Dentsply). In addition, the effect of QMix solution when used for a shorter (1 minute) and a longer application time (3 minutes) was investigated. Materials and Methods: Fifty permanent human teeth were prepared with K3 rotary system and 6% sodium hypochlorite. Samples were randomly assigned to five groups (n = 10) according to the final irrigation protocol: G1, negative control (distilled water); G2, positive control (QMix 1 minute); G3, QMix 1 minute/UAI; G4, QMix 1 minute/EC; G5, QMix 3 minutes. Subsequently the teeth were prepared and three photomicrographs were obtained in each root third of root walls, by scanning electron microscopy. Two blinded and pre-calibrated examiners evaluated the images using a four-category scoring system. Data were statistically analyzed using Kruskal-Wallis and Dunn tests (p < 0.05). Results: There were differences among groups (p < 0.05). UAI showed better cleaning ability than EC (p < 0.05). There were improvements when QMix was used with auxiliary devices in comparison with conventional irrigation (p < 0.05). Conventional irrigation for 3 minutes presented significantly better results than its use for 1 minute (p < 0.05). Conclusions: QMix should be used for 1 minute when it is used with UAI, since this final irrigation protocol showed the best performance and also allowed clinical optimization of this procedure.

• Journal of Conservation Science
• /
• v.25 no.4
• /
• pp.451-464
• /
• 2009

To do conservation for ceramics, sometimes it needs to clean the ceramics chemically to remove stains on the ceramics, which should be performed with caution. This study will provide quantitative data about the extraction characteristics of major elements from ceramics through the soaking test to evaluate the stability of ceramic cleaning agents. As soft textured pottery(fired at $700^{\circ}C$) had high absorption, it showed higher extraction characteristics in short soaking time. Especially the strong acid among chemical cleaning agents caused the expoliation and the color change on the surface of soft textured pottery. But these color change had no effect on the physical characteristics of soft textured pottery. The hard textured pottery(fired at $1,000^{\circ}C$) is relatively stable in the cleaning agent because it is ascertained the extraction of that was not enough and also it had little chromatic and physical change by strong acid. Porcelains(Celadon, Whiteware and Puncheong ware) was safer than the soft textured pottery due to their low extraction. But it should take precautions to clean the porcelains with lots of cracklewares such like Puncheong ware chemically in connection with the extraction characteristics and their cracklewares.

• Clean Technology
• /
• v.19 no.3
• /
• pp.264-271
• /
• 2013

In this study, we optimized the removal condition of contaminants attached on the scrap surface to recycle the scrap generated from the Zr alloy tube manufacturing process back to the nuclear grade. The main contaminant is remnant of watersoluble cooling lubricant that is used in the pilgering manufacture during the tube production, and it is assumed to be compressed and carbonized on the surface of tube. Zirlo alloy tube of ${\phi}9.50mm$, which has high occurrence frequency of scrap, was selected as the object to be cleaned, and cleaning abilities of reagents were evaluated by measuring the characteristics of contaminants remained and by analyzing the surface of the tube after cleaning process. For evaluation of each cleaning agent, we selected two types of sodium hydroxide series and three types of potassium hydroxide series. Furthermore, to confirm dependence on tempe-rature and ultrasonic intensities, cleaning at the room temperature, $40^{\circ}C$, and $60^{\circ}C$ was conducted, and results showed that higher the cleaning temperature and higher the ultrasonic intensity, better the cleaning effect. As a result of the bare-eye inspection, while the use of sodium hydroxide provided satisfactory condition on the tube surface, the use of potassium hydroxide series provided satisfactory condition on the tube surface only when the ultrasonic intensity was over 120 W. In the cleaning effect analysis using the gravimetric method, cleaning efficiency of sodium hydroxide series was as high as 97.6% ($60^{\circ}C$, 120 W), but since the tube surface condition was poor after the use of potassium hydroxide, the gravimetric method was not appropriate. In the analytical result of surface contaminants on the tube surface, C, O, Ca, and Zr were detected, and mainly C and O dominated the proportion of contaminants. It was also found that the degree of cleaning on the tube affected the componential ratio of C and O; if the degree of cleaning is high, or if cleaning is well-conducted, the proportion of C is decreased, and the proportion of O is increased. Based on these results, optimal cleaning for application in the industry can be expected by categorizing cleaning process into three steps of Alkali cleaning, Rinsing, and Drying and by adjusting cleaning parameters in each step.

• The Research Journal of the Costume Culture
• /
• v.19 no.1
• /
• pp.96-103
• /
• 2011

It is well known that the Petasites japonicus has been used for a long time medicine for the treatment of allergic diseases such as lacquer poisoning. However, the exact components and dyeing properties of its effects is still not known. Therefore, the purpose of this study was to investigate the dyeing property and ultraviolet-cut ability of silk and nylon fabrics that was dyed variously with the Petasites japonicus. The Petasites japonicus extract was done by boiling with distilled water at $100^{\circ}C$ for 1 hour. As mordanting agent, we used Aluminum potassium sulfate ($AlK(SO_4)_2{\cdot}12H_2O$), Copper(II) sulfate pentahydrate ($CuSO_5{\cdot}5H_2O$), Iron(II)Chloride ($FeCl_2{\cdot}4H_2O$). The best K/S value of dyeing temperature and time, all the fabrics were $100^{\circ}C$, 90min. Silk fabric was dyed yellow(0.8Y 7.6/2.2) and nylon fabric was dyed reddish yellow(10.1 YR 7.4/3.0). Silk fabric and nylon fabric was changed greenish yellow on mordanting with $CuSO_5{\cdot}5H_2O$ and $FeCl_2{\cdot}4H_2O$ respectively. And the colorfastness of washing and dry-cleaning was improved by using mordanting agent(4~5 grade). Ultraviolet-cut ability(UV-B) was showed more 90% in dyed nylon fabrics.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.487-494
• /
• 2005

Nowadays a large amount of wastewater containing metal working fluids and cleaning agents is generated during the cleaning process of parts working in various industries of automobile, machine and metal, and electronics etc. In this study, aqueous or semi-aqueous cleaning wastewater contaminated with soluble or nonsoluble oils was treated using ultrafiltration system. And the membrane permeability flux and performance of oil-water separation (or COD removal efficiency) of the ultrafiltration system employing PAN as its membrane material were measured at various operating conditions with change of membrane pore sizes and soil concentrations of wastewater and examined their suitability for wastewater treatment contaminated with soluble or insoluble oil. As a result, in case of wastewater contaminated with soluble oil and aqueous or semi-aqueous cleaning agent, the membrane permeability increased rapidly even though COD removal efficiency was almost constant as 90 or 95％ as the membrane pore size increased from 10 kDa to 100 kDa. However, in case of the wastewater contaminated with nonsoluble oil and aqueous or semi-aqueous cleaning agent, as the membrane pore size increased from 10 kDa to 100 kDa and the soil concentration of wastewater increased, the membrane permeability was reduced rapidly while COD removal efficiency was almost constant. These phenomena explain that since the membrane material is hydrophilic PAN material, it blocks nonsoluble oil and reduces membrane permeability. Thus, it can be concluded that the aqueous or semi-aqueous cleaning solution contaminated with soluble oil can be treated by ultrafiltration system with the membrane of PAN material and its pore size of 100 kDa. Based on these basic experimental results, a pilot plant facility of ultrafiltration system with PAN material and 100 kDa pore size was designed, installed and operated in order to treat and recycle alkaline cleaning solution contaminated with deep drawing oil. As a result of its field application, the ultrafiltration system was able to separate aqueous cleaning solution and soluble oil effectively, and recycle them. Further more, it can increase life span of aqueous cleaning solution 12 times compared with the previous process.

• The Research Journal of the Costume Culture
• /
• v.16 no.1
• /
• pp.158-165
• /
• 2008

The purpose of this study was to investigate the dyeing property and ultraviolet-cut ability on silk 100% and nylon 100% fabrics dyed with Rhus verniciflua extracts. This study was investigated K/S values, surface color, washing fastness, dry cleaning fastness and ultraviolet-cut ability of the silk and nylon fabrics dyed with Rhus verniciflua extracts under the various dyeing conditions. As mordanting were used Tin(II) Chloride dihydrate $(SnCl_2{\cdot}2H_2O)$, Copper(II) sulfate pentahydrate$(CuSO_5{\cdot}5H_2O)$, Iron(II)Chloride$(FeC_2{\cdot}4H_2O)$. pH was adjusted by sodium carbonate$(Na_2CO_3)$ and formic acid(HCOOH). The optimum dyeing temperature, dyeing time, and pH of the silk fabrics dyed with Rhus verniciflua extracts were $90^{\circ}C$, 100min, and in the nylon fabrics were $90^{\circ}C$, 45min. It were colored(munsell value) 6.4Y 7.5/4.1 in the silk fabrics and colored 4.3Y 6.6/5.9 in the nylon fabrics dyed with Rhus verniciflua extracts. Washing fastness and dry-cleaning fastness in the silk and nylon fabrics dyed with mordanting agent improved in $4{\sim}5$ grade. UV-A test showed that nylon fabrics a high rate of 92% with Rhus verniciflua extracts.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.2
• /
• pp.232-239
• /
• 2011

Fabric fibrous filter has been used in various industrial applications owing to the low cost and wide generality. However, the basic properties of fabric materials often limit the practical utilization including hot gas cleaning. This study attempts to find new coatings of porous fibrous filter media in order to overcome its insufficient thermal resistance and durability. Teflon was one of the plausible chemicals to supplement the vulnerability against frequent external thermal impacts. A foaming agent composed of Teflon and some organic additives was tentatively coated on the glass fiber mat. The present test Teflon foam coated filter was fount to be useful for hot gas cleaning, up to $250^{\circ}C$-$300^{\circ}C$. Close examination using XPS(X-ray Photoelectron Spectroscopy) and Contact angle proved the binding interactions between carbon and fluorine, which implies coating stability. The PTFE/Glass foam coated filter consisted of more than 95% (C-F)n bond, and showed super-hydrophobic with good-oleophobic characteristics. The contact angle of liquid droplets on the filter surface enabled to find the filter wet-ability against liquid water or oil.

• Journal of Industrial Technology
• /
• v.37 no.1
• /
• pp.12-15
• /
• 2017

It is important in dentistry that the provisional cement should be cleaned thoroughly from the crown before definitive cementation. The provisional cement has been removed by physical means such as curette, scaler, pumice, or sand-blasting with alumina particles, which is time-consuming, irritating, tedious, even causing crack. To avoid such troubles occurring through such physical cleaning means, the chemical solutions for dissolving the provisional cement remaining in dental crown were prepared, and solubilizing power of the solutions was measured and compared. The solution composed of MEA, NaOH, chloride chemicals ($CHCl_3$, $CCl_4$, $CH_2Cl_2$), surfactants (Igepal, Tween20), chelating agent (EDTA), and Ethyl cellosolve was most effective for dissolving the provisional cement.