• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.2
• /
• pp.24-29
• /
• 2002

A study for the circularity of machine tool is classified into two ways. One is to measure the circularity of machine tool by a existing measuring device. The other is to measure the circularity by remodeling the existing measuring device. We will improve on measurement of circularity using circular test method by a two-dimensional probe and a master ring for machining tools and investigate influence of trigger method, acceleration data sampling.

• Resources Recycling
• /
• v.31 no.6
• /
• pp.66-72
• /
• 2022

The circularity and particle size distribution of products obtained from dry classification after circularity tests using a high-intensity mixer were investigated to evaluate the use of domestic graphite concentrate as a lithium-ion battery material. At a rotor speed of 3,000 rpm, the particle size and circularity of the concentrated sample and product were unchanged. The circularity increased and particle size decreased when the rotor speeds were increased to 6,000 rpm, 10,000 rpm, and 12,000 rpm and the operating time was increased. For instance, the circularity increased from 0.870 to 0.936 when the rotor speed was increased from 3,000 rpm to 12,000 rpm for an operating time of 10 min. After the circularity test, dry classification was performed, wherein the circularity of the coarse particles was found to have increased to 0.947. Round particles were observed in the SEM images, indicating that high circularity was successfully achieved.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.977-981
• /
• 2000

Direct drive linear motors have large potential for use as high speed machine tool feed units since they can increase machining rates and improve servo accuracy by eliminating gear related machining problems. So, in this paper, characteristic of 2-axis linear motor feed unit are studied and control gain are adjusted considering positioning, velocity, acceleration and static stiffness. We confirm linear motor feed unit are affected value of control gain sensitively, because drive directly. From the experiment, this feed unit has l${\mu}{\textrm}{m}$ micro step resolution, 5.7${\mu}{\textrm}{m}$ positioning accuracy and under 60${\mu}{\textrm}{m}$ circularity.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.2
• /
• pp.84-89
• /
• 2011

This paper studied the carburizing of chromium molybdenum steel which the heat treatment effect of gear geometric tolerance, OPD, Runout, the surface hardness, the maximum hardness, the core hardness and the bending fatigue strength were investigated. Firstly, the deformation is observed, and the results of circularity, squareness, OPD and Runout of SCM822, SCM425, and SCM415 are obtained in order. Secondly, in order to investigate the gear hardness, the surface hardness, the maximum hardness and the core hardness of SCM822, SCM425, and SCM415 are obtained; and the surface hardness of SCM822 is about 10% higher than SCM415's, and about 3% higher than SCM425's. Thirdly, the fatigue strength of SCM822 is about 10% higher than SCM415's, and about 7% higher than SCM425's in the fatigue test results. At last, for the purpose of the minimum deformation of heat treatment, and also the improvement of fatigue strength, the best gear material is SCM822 in this test.

• Computers and Concrete
• /
• v.33 no.5
• /
• pp.605-619
• /
• 2024

The increase of reclaimed asphalt pavement (RAP) content in recycled asphalt concrete (RAC) is accompanied by the degradation of low-temperature cracking resistance, which has become an obstacle to the development of RAC. This paper aims to reveal the meso-scale mechanisms of the low-temperature fracture behavior of RAC and provide a theoretical basis for the economical recycling of RAP. For this purpose, micromechanical heterogeneous peridynamic model of RAC was established and validated by comparing three-point bending (TPB) test results against corresponding numerical simulation results of RAC with 50% RAP content. Furthermore, the models with different aggregate shapes (i.e., average aggregates circularity (${\bar{C_r}}=1.00$, 0.75, and 0.50) and RAP content (i.e., 0%, 15%, 30%, 50%, 75%, and 100%) were constructed to investigate the effect of aggregate shape and RAP content on the low-temperature cracking resistance. The results show that peridynamic models can accurately simulate the low-temperature fracture behavior of RAC, with only 2.9% and 13.9% differences from the TPB test in flexural strength and failure strain, respectively. On the meso-scale, the damage in the RAC is mainly controlled by horizontal tensile stress and the stress concentration appears in the interface transition zone (ITZ). Aggregate shape has a significant effect on the low-temperature fracture resistance, i.e., higher aggregate circularity leads to better low-temperature performance. The large number of microcracks generated during the damage evolution process for the peridynamic model with circular aggregates contributes to slowing down the fracture, whereas the severe stress concentration at the corners leads to the fracture of the aggregates with low circularity under lower stress levels. The effect of RAP content below 30% or above 50% is not significant, but a substantial reduction (16.9% in flexural strength and 16.4% in failure strain) is observed between the RAP content of 30% and 50%. This reduction is mainly attributed to the fact that the damage in the ITZ region transfers significantly to the aggregates, especially the RAP aggregates, when the RAP content ranges from 30% to 50%.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.105-108
• /
• 1995

So far,in deep drilling process there are several manufacturing problems such as hole deviation, hole over size, circularity,straightness and surface roughness. Whit regard to these problems, we atudied the abrasion process on carbided tip of BTA drill and got the follow test results through the abrasion characteristic test and analysis on cutting mechanism for the drill tooth and guide pad. 1) In SM55C drilling process, the most stable and reasonable drilling speed range for optmum abrasion characteristic of drill tooth was 60m.min. 2) The total drilling torque was about 60kg .deg.cm on condition drilling speed 60m/min and 0.15mm/rev. These results show that the theoretical burnising torque is well accord with the tested torque which is working on guide pad.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.446-451
• /
• 1999

A study for the roundness of machining center is classified into two ways. one is the way that progresses the roundness amending the parameter of machining center based on the measured value after the measurement of the roundness of machining center by means of a existing measuring device, another is the way that measures the roundness by remodeling the existing measuring device. The former is studied by pack hei jae team in Seoul university, the latter is studied by TSUTSUMI. Especially TSUTSUMI measures the roundness according to circular compensation after the insertion of developed measuring desire using a rotary encoder to the spindle of machining tool. We study how regulation velocity occuring with circular motion of machining center table influences the roundness after measuring the roundness using Circular Test method by a 2 dimention probe and a standard discus in this experiment.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.75-81
• /
• 2000

This study for the roundness and perpendicularity of machining center is classified into two ways. One is the way that progresses the roundness amending the parameter of machining center based on the measured value after the measurement of the roundness of machaning center by means of a existing measuring device, another is the way that measures the roundness by remodeling the existing measuring device. the former is studied by pack hei jae team in Seoul university, the later is studied by TSUTSUMI. Especially TSUTSUMI measures the roundness according to circular compensation after the insertion of developed measuring device using a rotary encoder to the spindle of machining tool. we study how regulation velocity occuring with circular motion of machining center table influences the roundness after measuring the roundness using Circular Test method by a 2 dimention probe and a standard discus in this experiment.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.4
• /
• pp.41-47
• /
• 2009

This research deals with evaluation of machining accuracy for Parallel Kinematic Machine Tool(PKMT) applied parallel type robot system with high precision and stiffness. For this purpose, machine simulation is carried out to foreknow collision and interference between workpiece and tool. Furthermore, on the basis of machine simulation data, PKMT is manufactured. Machining accuracy such as cylindricity straightness, squareness, parallelism circularity, concentricity pitch error and yaw error, is measured by using coordinate measuring machine. Test piece for evaluation of machining accuracy is designed and manufactured under the standard of ISO 10791-7.

• Journal of Biomedical Engineering Research
• /
• v.10 no.1
• /
• pp.1-10
• /
• 1989

An automatic lung nodule detection algorithm was applied for digital radiographic images using Bit Slice Processor. In this algorithm, signal enhancing filtering and signal suppressing filtering were performed on the given digital chest image, respectively. Then we grit the dirt- frrence image from these filtered images, and hi-level island images were obtained by applying various threshold values. From the island images, we decided the suspicious nodules using size and circularity test, and marked them to alert radiologists. The performance of the atgorithm was analyzed with respect to the size, contrast and position of digitally synthesized nodules. This method presented 45.8% of true positive ratio for the nodules of lOw in diameter with 12-16 pixel value differnces.