• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.296-303
• /
• 1987

본 논문에서는 동력전달용 기어에 주로 쓰이는 물림률 1.3 이상일 때, 치면접 촉응력과 공칭굽힘응력이 작게되는 풀림각 1˚로 고정하여 잇수 30∼100개 압력각 14˚∼30˚의 범위에서 최소 원호반경식과 치형 조건을 만족하는 최대 원호반경식에 대하여 고찰하였다.

• 대한기계학회논문집
• /
• 제11권2호
• /
• pp.198-204
• /
• 1987

본 논문에서는 전보에서 창성된 인벌류우트-원호합성치형기어에 있어서 Hertz 식에 의하여 치면접촉응력을 구하고 유한요소법에 의하여 이뿌리응력을 계산하였다. 그리고 같은 제원의 표준 인벌류우트 치형기어와 비교하였다.

• Tribology and Lubricants
• /
• 제30권4호
• /
• pp.212-217
• /
• 2014

A counter gear transmits the rotation angle, so the angular velocity ratio of the gear does not necessarily need to be constant in the meshing process. As a pinion has a small number of teeth when combined with an internal gear for counters, tooth interference can occur with the use of an involute curve. This paper introduces circular arcs that represent a tooth profile and fillet for the profile design of a pinion through the combination of arcs with lines. The straight line of a rack tooth represents the profile of a mating internal gear. Thus, the circular arc and line maintain contact during the rotation of the counter gear. This paper presents an analysis of the meshing of the circular arc tooth and rack tooth along with the properties of the counter gear, such as the change in rotational velocity and amount of backlash. The contact ratio of the counter gear is 1 because the tooth contact occurs between circular arcs and line. The initial position of tooth contact, which denotes the simultaneous contact of two teeth, is found. As the rotation of the pinion, only one tooth keeps the contact situation. This meshing property is analyzed by the geometrical constraints of the tooth profile in contact and the results are presented as graphical diagrams in which tooth-arc movements are superimposed.

• 대한기계학회논문집
• /
• 제10권6호
• /
• pp.870-875
• /
• 1986

본 연구에서는 랙의 이끝부분을 full-rounded tip으로 설계한 후, 이에 의하 여 창성되는 피니언의 이뿌리곡선을 구하여 전체치형을 완성하였다. 그리고 합성치 형기어의 미끄름율, 유효이뿌리원에서의 공칭굽힘응력과 두쌍접촉호의 길이대 원호부 분접촉호의 길이의 비인 접촉계수를 해석적인 방법으로 구하였다.또한 이들 특성들 과 물림율등 제특성을 비교.검토하여 공구압력각, 인벌류우트부분의 크기를 나타내는 물림각 및 원호반경등의 변화에 대한 제특성의 변화를 고려한 합성치형의 성능을 향상 시킬 수 있는 설계방법을 구하였으며, 합성치형과 표준인버류우트치형을 비교하였다.

• 대한기계학회논문집
• /
• 제9권5호
• /
• pp.572-578
• /
• 1985

본 논문에서는 인벌류우트와 원고치형의 단점을 보완하고 양자의 장점을 취한 치형을 얻기위하여 피치점 부근에서는 인벌류우트치형으로 이끝부분에서는 원호로 하 고 이뿌리부분에서는 상대방 기어의 원호부분과 맞물릴 수 있는 곡선으로 하는 치형을 합성하고, 이 합성치형의 유효치형을 가공할 수 있는 랙치형을 이론적인 방법으로 구 하였다. 그리고, 이 합성치형의 유효치형에 대한 이끝과 이뿌리 두께의 변화와 물림 률을 검토하였다.

• Structural Engineering and Mechanics
• /
• 제43권4호
• /
• pp.439-448
• /
• 2012

This paper investigates the load sharing of double circular arc helical gears considering the influence of assembly errors. Based on a load sharing formulae, a three-dimensional finite element tooth contact analysis (TCA) is implemented with commercial software package ANSYS. The finite element grid for the double circular arc gear contact model is automatically generated by using the APDL (ANSYS Parameter Design Language) embedded in ANSYS. The realistic rotation of gears is achieved by using a coupling degree-of-freedom method. Numerical simulations are carried out to exemplify the proposed approach. The distribution of contact stress and bending stress under specific loading conditions are computed and compared with those obtained from Hertz contact theory and empirical formulae to demonstrate the efficiency of the proposed load sharing calculation formulae and TCA approach.

• Tribology and Lubricants
• /
• 제1권1호
• /
• pp.69-79
• /
• 1985

Planocentric gears 장치에서 내치차에 pin type의 치형을 사용하고 휠의 치형을 원호로 구성하였을 경우 치의 접촉특성을 탄성유역학적 윤활이론을 도입하여 해석 하였다. 윤활 특성을 개선하기 위하여 물림 위치(meshing position)에 의거한 설계 방법과 치의 모서리 부분 형상을 만곡되게 하는 치형 설계 방법을 제시하고 기존 설계에 의한 장치와 수치적으로 특성을 비교 하였다.

• 한국정밀공학회지
• /
• 제1권3호
• /
• pp.85-94
• /
• 1984

The WILDHABER-NOVIKOV gear, one of the circular arc gears, has the large contact area between the convex and concave profiled mating teeth, moves from one end of the tooth to the other axially making a face contact. Hence it provides a large load capacity than the Involute gear and still satisfying the law of gearing. In order to analyze the gear stress, a photoelastic investigation was carried out. Photo elastic model of the WILDHABER-NOVIKOV gears were made of Araldite CT200 in this investigation. For both the many teeth gear and the few teeth gear segments, External gears of all addendum type WILDHABER-NOVIKOV gear and the involute gear were tested. Included were the models with various profile raddi at the same pressure angle 20 .deg. and module 13.5. The flank stresses and fillet stresses of these gears were observed in each case and compared with those of gears. From this investigation, the following results were obtained. A. In the case of having many teeth gear: As the profile radius is increased, the fillet stresses of the WILDHABER-NOVIKOV gear become the same or less than that of the INVOLUTE gea, and the flank stress becomes smaller than that of the INVOLUTE gear. Therefore the better design condition is satisfied with a large profile radius. B. IN the case of having a few teeth gear: As the profile radius is increased the flank stress of WILDHABER-NOVIKOV gear becomes smaller than that of the INVOLUTE gear, but the fillet stresses become larger than that of the INVOLUTE gear. Therefore the larger design condition is satisfied with small profile radius.

• Tribology and Lubricants
• /
• 제36권2호
• /
• pp.64-67
• /
• 2020

In the conventional gerotor design, the circular arc tooth of the outer rotor is first introduced, and then the inner rotor profile is generated by simulating the outer rotor motion while the inner rotor is fixed. The profile generation of tooth meshing exhibits relativity; therefore, the outer rotor profile can be generated by the movement of the inner rotor. In this study, we propose the design of a gerotor with a pin-tooth inner rotor. First, the pin-tooth inner rotor is devised, and then the outer rotor profile is generated. The profile of the inner rotor is simply composed of equally arranged pins along a circle. The root of the inner rotor is designed as a conjugated arc of two pins. The trajectory of the pin center is obtained by the inner rotor operation, and then the outer rotor profile is determined as a parallel curve of the trajectory. In this gerotor design, the inner rotor has a simple configuration, and contact occurs between the pin parts of the inner rotor and the whole profile of the outer rotor. This affects the material selection and machining process. The pin tooth can be used to design the outer and inner rotors, enabling a double gerotor mechanism corresponding to a planetary gear system.