• Journal of the Korean Geotechnical Society
• /
• v.33 no.11
• /
• pp.35-43
• /
• 2017

In this study, the pull-out resistance behavior of the anchor with the bump type resistors at the anchor body was experimentally investigated. In the model tests, the pull-out resistance was measured by pulling out the anchor at a constant speed. Anchor body was installed in the center of the circular sand tank. Pull-out tests were conducted for 10 conditions. The anchor type (existence of the resistor), the friction conditions of the anchor body surface ($1/3{\phi}$, $2/3{\phi}$, ${\phi}$), the bump type resistor set number (1set, 2set, 4set), and the height of resistors (0.05d, 0.10d, 0.20d) were varied. The load-displacement relationship for each conditions was measured during the pull-out tests at a constant speed (1 mm/min). Maximum pull-out length was 80 mm. As a result, the pull-out behavior of the friction type anchor and the expansion type anchor was different. As the number of resistor increased, the maximum pull-out resistance increased and the residual pull-out resistance ratio increased significantly, which were at 171~591 percent larger than that of the friction type anchor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.352-361
• /
• 2021

An underwater positioning method that can be applied to structures for underwater construction is being developed at the Korea Institute of Ocean Science and Technology. The method uses an extended Kalman filter (EKF) based on an inertial navigation system for precise and continuous position estimation. The observation matrix was configured to be variable in order to apply asynchronous measured sensor data in the correction step of the EKF. A Doppler velocity logger (DVL) can acquire signals only when attached to the bottom of an underwater structure, and it is difficult to install and recover. Therefore, a complex sensor device for underwater structure attachment was developed without a DVL in consideration of an underwater construction environment, installation location, system operation convenience, etc.. Its performance was verified through a water tank test. The results are the measured underwater position using an ultra-short baseline, the estimated position using only a position vector, and the estimated position using position/velocity vectors. The results were compared and evaluated using the circular error probability (CEP). As a result, the CEP of the USBL alone was 0.02 m, the CEP of the position estimation with only the position vector corrected was 3.76 m, and the CEP of the position estimation with the position and velocity vectors corrected was 0.06 m. Through this research, it was confirmed that stable underwater positioning can be carried out using asynchronous sensors without a DVL.

• Korean Journal of Ichthyology
• /
• v.34 no.2
• /
• pp.86-95
• /
• 2022

Egg development and morphological change of larvae and juvenile of the Roughscale sole, Clidoderma asperrimum, were investigated in the present study. Adult fishes were collected on the East Sea, Korea, from 2017 to 2018 and reared in a circular water tank (Ø 6×1 m) at water temperature of 12.8±1.9℃. Fertilized eggs ranged from 1.42 to 1.59 mm (mean 1.51±0.04 mm, n=50) in diameter. The eggs were spherical in shape, transparent, floating and colorless. The egg yolk was separated from the egg membrane 60 mins post-fertilization (PF), and an embryo was formed in 62 hrs PF. More than 50% of the eggs hatched within 144 hrs PF in the range of 10.2~11℃(mean 10.8℃). The size of the newly hatched larvae were 4.22~4.64 mm (mean 4.53±0.16 mm) in total length (TL), their mouth and anus were not open yet. At 10 days after hatching, the preflexion larvae reached 5.88~6.62 mm (mean 6.31±0.33 mm) in TL, and the yolk absorption was completed and the mouth began to open. At 55 days after hatching the larvae reached to flexion larvae stage and they were 10.4~13.3 mm (mean 12.7±1.3 mm) in TL, and the tip of notochord was bent upward. At 120 days after hatching the larvae reached to juvenile stage and they were 35.3~40.5 mm (mean 39.5±2.4 mm) in TL. Their all fins had completed set of the fin-rays (D. 79~94: A. 63~75) and the juveniles adopted a benthic life.

• Fisheries and Aquatic Sciences
• /
• v.26 no.12
• /
• pp.726-737
• /
• 2023

Piperine, the main bioactive component of black pepper (Piper nigrum Linn.), has anti-inflammatory, antifungal, and antibacterial properties. This study evaluated the supplemental effects of piperine or black pepper on innate immunity, growth, feed utilization efficiency, and intestinal morphology in red seabream (Pagrus major). Six experimental diets were formulated, supplementing piperine at 0.0, 0.25, 0.5, 1.0, and 2.0 g/kg levels (Con, P25, P50, P100, and P200) or 1.0 g/kg black pepper (BP100). Juvenile fish (7.6 ± 0.1 g) were randomly stocked into 18 circular tanks (220 L), including 30 fish per tank. Each diet was randomly assigned to triplicate groups, and the feeding trial was conducted for 8 weeks. The results showed that final body weight, specific growth rate, weight gain, and feed utilization efficiency were significantly improved (p < 0.05) when piperine was supplemented into diets at 0.25-2.0 g/kg levels compared to the Con group. Compared to the Con diet, condition factor was significantly increased (p < 0.05) in fish fed with dietary piperine at 0.25-2.0 g/kg or BP100 diet. Serum myeloperoxidase activity was increased (p < 0.05) in P25 and P100 groups and antiprotease activity was increased (p < 0.05) in P100 group compared to the Con group. Significantly higher (p < 0.05) lysozyme activity was observed in P50, P100, P200 and BP100 groups, while total immunoglobulin level was increased in P50, P100 and BP100 groups than Con group. Superoxide dismutase activity was increased (p < 0.05) by dietary piperine at 0.25-2.0 g/kg levels and BP100 diet compared to Con diet. Plasma cholesterol was significantly lower (p < 0.05) in fish fed with piperine (0.5-2.0 g/kg) or BP100 compared to the Con diet. Compared to the Con diet significantly longer (p < 0.05) intestinal villi were observed in fish fed with piperine at 0.25-1.0 g/kg levels, and higher goblet cell count was observed in P25 and BP100 groups. Dietary inclusion of piperine would be a potent immunostimulant in fish diet and the optimum supplementation level would be 0.25-1.0 g/kg.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.4
• /
• pp.360-364
• /
• 1990

To testy time division scheme, we performed some experiments in a circular water tank(13m in diameter and 1m deep). A result of that is shown in figure 4. The 2-dimensional position of the pinger was calculated by the method of hyperbolic line of position calculation. The resolution of the time difference on the base line is 2.5cm. In experiments, the multiple pingers of a single frequency were distinguished and tracked successfully. When the experiment is carried out in the water tank, some multi-path pulses always occur. To delete it, several 10 ms of time delay is inserted onto the program after a group of the normal signals are received. Some normal pulses are not received by the time delay, however there is no problem, practically, for the distinction and the tracking of the pulse. In 2-dimensional positioning, the pinger position can be calculated with three hydrophones. However, if four hydrophones are available, the positioning accuracy will be higher than three hydrophones only by some techniques. Another good feature of the use of four hydrophones is that the positioning of the pinger is capable if a hydrophone fails in receiving them. We also tested this distinguishing method in the field using another type pingers(APPENDIXA).

• Membrane Journal
• /
• v.19 no.3
• /
• pp.252-260
• /
• 2009

The effects of the treatment of an acidic solution at pH 2 on polyacrylonitrile ultrafiltration (UF) membranes were investigated using a circular cross-flow filtration bench with a membrane module. A substantial reduction in the membrane permeability was observed after 80 hours' treatment of the acidic solution. In addition, the analyses of the sample solutions by ultraviolet/visible absorption spectroscopy and gas chromatography/mass spectrometry (GC/MS), which were taken from the feed tank as a function of the treatment time, showed that a new organic compound was produced in the course of the treatment. From a thorough search of the mass spectral library we presumed the new compound to be 1,6-dioxacyclododecane-7,12-dione (DCD), one of the well-known additives for polyurethane. Based on further experimental results, including the scanning electron microscope (SEM) images and the solid-state NMR spectra of the membranes used for the treatment of the acidic solution, we suggested that the decrease of the permeate flux resulted not from the deformation of the membranes, but from the fouling by DCD eluted from the polyurethane tubes in the filtration bench during the treatment. Those results imply that the reactivity to an acidic solution of the parts comprising the filtration bench is as important as that of the membranes themselves for effective treatments of acidic solutions, for efficient chemical cleaning by strong acids, and also in determining the pH limit of the solutions that can be treated by the membranes.

• Korean Journal of Ichthyology
• /
• v.20 no.3
• /
• pp.173-178
• /
• 2008

The substrate preferences of juvenile black sea bass Centropristis striata (Linnaeus) was tested in a circular tank (1.5 m diameter${\times}$0.4 m deep) divided into two equal areas of oyster-related (oyster reef and whole oyster shell) and sand substrates. All trials were video taped for 20 min. Tapes were viewed on a monitor and locations of all fish recorded and timed with respect to substrate. $Mean{\pm}SE$ times on oyster shell were $18.1{\pm}2.0min$ (1-fish trial-1) and $17.5{\pm}1.7min$ (5-fish trial-1). $Mean{\pm}SE$ times on sand were $2.0{\pm}1.0min$ (1-fish trial-1) and $2.5{\pm}1.7min$ (5-fish trial-1). Black sea bass juveniles showed a significant preference for oyster reef and shell over sand substrate in single-fish trials (paired t-test, P<0.05) and also in five-fish trials (paired t-test, P<0.05). $Mean{\pm}SE$ times under oyster reefs were $16.6{\pm}2.0min$ in single-fish trials and $10.7{\pm}2.3min$ in five-fish trials. Mean numbers of movements among oyster reefs were $1.1{\pm}1.0$ in single-fish trials and $11.5{\pm}3.1$ in fivefish trials. Fish spent significantly less time under oyster reefs in five-fish trials, compared to single-fish trials (paired t-test, P<0.05) and they moved more frequently in five-fish trials than in single-fish trials (paired t-test, P<0.05). Significantly higher competition for a refuge in five-fish trials may induce less time under oyster reefs as well as frequent movement of black sea bass juveniles on shell substrate.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.17 no.1
• /
• pp.57-71
• /
• 2015

This study was conducted to develop the fertigation system with a peristaltic hose pump and brushless DC motor. The fertigation system was consisted of sensor, main controller, motor control unit, peristaltic pump, water supply pump, control panel, and filter. The peristaltic pump discharges liquid by squeezing the tube with rollers. Rollers attached to the external circumference of the rotor compresses the flexible tube. The fluid is contained within a flexible tube fitted inside a circular pump casing. The developed fertigation system has no mixing tank but instead injects directly a concentrated nutrient solution into a water supply pipe. The revolution speed of the peristaltic pump is controlled by PWM (Pulse width modulation) method. When the revolution speed of the peristaltic pump was 300rpm, the flow rate of the 3.2, 4.8, 6.3mm diameter tube was 202, 530, 857mL/min, respectively. As increasing revolution speed, the flow rate of the peristaltic pump linearly increased. As the inner diameter of a tube larger, a slope of graph is more steep. Flow rate of three roller was more than that of four roller. Flow rate of a norprene tube with good restoring force was more than that of a pharmed tube. As EC sensor probe was installed in direct piping in comparison with bypass piping showed good performance. After starting the system, it took 16~17 seconds to stabilize EC. The maximum value of EC was 1.44~1.7dS/m at a setting value of 1.4dS/m. The developed fertigation system showed ±0.06dS/m deviation from the setting value of EC. In field test, Cucumber plants generally showed good growth. From these findings, this fertigation system can be appropriately suitable for fertigation culture for crops.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.3
• /
• pp.196-213
• /
• 2001

A split beam ultrasonic transducer operating at a frequency of 70 kHz to use in the fish sizing echo sounder was developed and the acoustic radiation characteristics were experimentally analyzed. The amplitude shading method utilizing the properties of the Chebyshev polynomials was used to obtain side lobe levels below -20 dB and to optimize the relationship between main beam width and side lobe level of the transducer, and the amplitude shading coefficient to each of the elements was achieved by changing the amplitude contribution of elements with 4 weighting transformers embodied in the planar array transducer assembly. The planar array split beam transducer assembly was composed of 36 piezoelectric ceramics (NEPEC N-21, Tokin) of rod type of 10 mm in diameter and 18.7 mm in length of 70 kHz arranged in the rectangular configuration, and the 4 electrical inputs were supplied to the beamformer. A series of impedance measurements were conducted to check the uniformity of the individual quadrants, and also in the configurations of reception and transmission, resonant frequency, and the transmitting and receiving characteristics were measured in the water tank and analyzed, respectively. The results obtained are summarized as follows : 1. Average resonant and antiresonant frequencies of electrical impedance for four quadrants of the split beam transducer in water were 69.8 kHz and 83.0 kHz, respectively. Average electrical impedance for each individual transducer quadrant was 49.2$\Omega$ at resonant frequency and 704.7$\Omega$ at antiresonant frequency. 2. The resonance peak in the transmitting voltage response (TVR) for four quadrants of the split beam transducer was observed all at 70.0 kHz and the value of TVR was all about 165.5 dB re 1 $\mu$Pa/V at 1 m at 70.0 kHz with bandwidth of 10.0 kHz between -3 dB down points. The resonance peak in the receiving sensitivity (SRT) for four combined quadrants (quad LU+LL, quad RU+RL, quad LU+RU, quad LL+RL) of the split beam transducer was observed all at 75.0 kHz and the value of SRT was all about -177.7 dB re 1 V/$\mu$Pa at 75.0 kHz with bandwidth of 10.0 kHz between -3 dB down points. The sum beam transmitting voltage response and receiving senstivity was 175.0 dB re 1$\mu$Pa/V at 1 m at 75.0 kHz with bandwidth of 10.0 kHz, respectively. 3. The sum beam of split beam transducer was approximately circular with a half beam angle of $9.0^\circ$ at -3 dB points all in both axis of the horizontal plane and the vertical plane. The first measured side lobe levels for the sum beam of split beam transducer were -19.7 dB at $22^\circ$ and -19.4 dB at $-26^\circ$ in the horizontal plane, respectively and -20.1 dB at $22^\circ$ and -22.0 dB at $-26^\circ$ in the vertical plane, respectively. 4. The developed split beam transducer was tested to estimate the angular position of the target in the beam through split beam phase measurements, and the beam pattern loss for target strength corrections was measured and analyzed.