• Bulletin of the Korean Chemical Society
• /
• v.29 no.8
• /
• pp.1485-1490
• /
• 2008

Dumbbell-shaped aromatic amphiphilic molecules consisting of a dodeca-p-phenylene as a rigid segment and oligoether dendrons as a flexible chains were synthesized, characterized, and their aggregation behavior was investigated in the bulk and at the air-water interface. In contrast to the molecule 2 which shows a nematic liquid crystalline state, molecule 1 based on shorter dendritic chains was observed to self-assemble into a 3-D primitive orthorhombic supercrystal. And molecule 1 at the air-water interface was observed to reorganize from circular plates to ring structures by lateral compressions.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1042-1048
• /
• 2007

This work analytically investigated the radiated noise of a helical gear-housing system due to the excitation of helical gears. The helical gears were modeled as a 12-degree of freedom mass-spring-damper system; the shaft was modeled as a rod, a beam, and a torsional shaft; and the gear housing was modeled as a clamped circular plate with viscous damping. The modeling of this system used transfer matrices for helical gears, shafts, and bearings. Damping for both the bearings and the plate were obtained by modal testing. For the evaluation of noise, sound pressure from the plate due to the force and the moment in both radial and tangential directions was analytically derived by the Rayleigh integral. The analytical derivation and parameters from the experiment were applied to an analysis of noise for the two sets of helical gears with differing gear ratios. The analysis showed that the moment excitation in both helical gears contributed more to the noise of the plate than axial force excitation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.524-529
• /
• 1998

Analogous problem for a gear dynamics where helical gears excite logitudinal forces in the shaft is studied. These shaft forces excite the supporting gear housing through bearing, causing structural vibration. In this study, shaft is modeled as a rod, and bearing is modeled by a massless spring. A simple model for gear housing is a clamped circular plate. To model this force transmission, the transfer functions from the shaft to a clamped circular plate are analytically derived by using the spectral method and four-pole parameter. Finally, radiated noise is computed, using the acoustic relations due to plate surface vibration.

• ETRI Journal
• /
• v.36 no.6
• /
• pp.889-893
• /
• 2014

This paper presents a high-performance dual-circularly polarized feed employing a dielectric-filled circular waveguide. Novel features are incorporated in the proposed feed, such as a dielectric rod radiator for high gain and good impedance matching; dual quarter-wave chokes for low axial ratio over wide angles and for low back radiation; an integrated septum polarizer; and two end-launch-type coaxial-to-waveguide transitions. The proposed feed shows excellent performance at 5.0 GHz to 5.2 GHz.

• Journal of the Korean Physical Society
• /
• v.73 no.10
• /
• pp.1410-1419
• /
• 2018

A skier's motion was analyzed by a simple model consist of point mass m and a single rod connected to a single ski plate. We studied the conditions for the stable ski turn as functions of the linear velocity and the radius of the turn. The solutions for the stable ski turn in our model do not require any extra skier's movement to complete a stable circular turn. The solution may then give the skier the most comfortable skiing method without any active movement to control the ski. The generalized force supporting the point mass from the ski plate was calculated. We obtained the force from the ground (rebound force) without any geometrical structure of the ski plate. Adding an active movement to the direction of the ski plate, the conditions for the stable ski turn were also analyzed. Our result gives some insight for the skier who wants to develop technique.

• The Journal of the Acoustical Society of Korea
• /
• v.17 no.5
• /
• pp.79-84
• /
• 1998

본 논문은 길이방향으로 조화함수 형태로 변화하는 단면적을 가진 원형단면의 탄성 막대에서 전파하는 비틂 탄성파의 전파속도에 대한 이론적 및 실험적 결과를 제시한다. 주 기적인 미소한 반경 변화를 섭동법에 의해 다루어 전파속도의 이론적 근사해를 구하였다. 그결과 전파속도는 반경 변화 폭의 제곱에 비례하는 양 만큼 감소하는 경향이 나타났다. 이 론적 경향을 검증하기 위한 실험은 자왜현상으로 비틂파를 전파시키고 나사면을 가진 탄성 도파관에서 전파속도를 측정하는 방법으로 행하였다.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1998.06c
• /
• pp.323-326
• /
• 1998

The paper describes a theoretical and experimental study on the speed of the torsional elastic waves propagating in an axisymmetirc waveguide whose cross-sectional area varies periodically as an harmonic function of the axial coordinate. The approximate solution of the phase speed has been obtained using the perturbation technique for sinusoidal modulation of small amplitude. The experiment verifying the theoretical result consists of transmitting and receiving torsional waves by magnetostriction and measuring the wave speed in the waveguides with threaded surfaces.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.199-203
• /
• 2004

In this paper, a simplified model is studied to predict analytically the radiated noise from the helical gear system due to an axial excitation of helical gear. The simplified model describes gear, shaft, bearing, and housing. To obtain the axial force of helical gear, mesh stiffness is calculated in the load deflection relation. The axial force is obtained from the solution of the equation of motion, using the mesh stiffness. It is used as a longitudinal excitation of the shaft, which in turn drives the gear housing through the bearing. In this study, the shaft is modeled as a rod, while the bearing is modeled as a parallel spring and damper only supporting longitudinal forces. The gear housing is modeled as a clamped circular plate with viscous damping. For the modeling of this system, transfer function from the shaft to the clamped plate are used, using a spectral method with four pole parameters. Out-of-plane displacement for the thin circular plate with viscous damping is derived and sound pressure radiated from the plate is also derived. Using the model, parameter studies are carried out.

• Smart Structures and Systems
• /
• v.16 no.4
• /
• pp.579-591
• /
• 2015

This paper investigates a magnetoelectric (ME) vibration energy harvester that can scavenge energy in arbitrary directions in a plane as well as wide working bandwidth. In this harvester, a circular cross-section cantilever rod is adopted to extract the external vibration energy due to the capability of it's free end oscillating in arbitrary in-plane directions. And permanent magnets are fixed to the free end of the cantilever rod, causing it to experience a non-linear force as it moves with respect to stationary ME transducers and magnets. The magnetically coupled cantilever rod exhibits a nonlinear and two-mode motion, and responds to vibration over a much broader frequency range than a standard cantilever. The effects of the magnetic field distribution and the magnetic force on the harvester's voltage response are investigated with the aim to obtain the optimal vibration energy harvesting performances. A prototype harvester was fabricated and experimentally tested, and the experimental results verified that the harvester can extract energy from arbitrary in-plane directions, and had maximum bandwidth of 5.5 Hz, and output power of 0.13 mW at an acceleration of 0.6 g (with $g=9.8ms^{-2}$).

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.3
• /
• pp.87-95
• /
• 2002

원주의 항력 감소와 원주 주위 유동의 제어에 대하여 실험적으로 연구하였다. 원주 주위 유동을 제어하기 위하여 작은 제어봉을 원주 전방에 설치하였다. 실험시 원주 직경(D=30mm)에 기초한 레이놀즈수는 $Re=2 {/times} 10^4$이었다. 제어봉의 직경(d)은 4mm, 5mm, 6mm, 7mm로 변화시켰으며, 원주와 제어봉 사이의 거리(L)를 조절하면서 원주의 표면압력분포와 후류속도를 측정하였다. 제어봉으로부터의 와 유출이 사라지는 임계거리 (critical distance) $ L_C$는 $ L_C$ /D=1.5+0.83d이었는데, $ L_C$를 전후로 유동특성과 항력값이 크게 바뀌었다. 특히 원주와 제어봉 사이의 거리가 임계거리보다 짧은 경우에는 항력이 감소하다가 $ L_C$보다 크게 되면 증가하는 경향을 보였다. 제어봉의 직경이 d/D=0.233인 경우, L/D=2.013의 조건에서 원주는 약 29%의 항력 감소를 보였고, 전체 항력은 L/D=1.833조건에서 약 25% 항력이 감소하였다.