• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.267-270
• /
• 2002

LCD is not very expensive and according to the principle that twisted-nematic LCD can modulate by electric signal, lots of researches been developed about many of theory, methods of design and calculating parameters effectively. In 1999 J. A. Davis et ai. proposed the method of deciding upon extraordinary and ordinary axis direction, which is based on Blazing Effect, inspect into changes of diffraction patterns. But in laboratory, it is difficulty to observe 5th or 6th diffraction pattern, and not clear in mathematical. In this paper, illuminating circular polarized beam been to TN LCD (twisted-nematic LCD), we found extraordinary axis direction with inspecting into maximum intensity distribution appeared in the side of analyzer Using Jones matrix method, we endowed with mathematical propriety.

• ETRI Journal
• /
• v.22 no.1
• /
• pp.12-19
• /
• 2000

Wireless communication systems using airship have been proposed in worldwide. The airship will be located at the stratosphere about $20{\sim}23\;km$ above the sea level. The position of airship will vary within the station keeping range with time due to the drag of the wind in the stratosphere. When the earth station antenna has a high gain without the tracking function, the antenna performance may be degraded by a small variation of the airship. This means that variation of airship location could result in serious degradation of the system performance. In this paper, degradation in earth station's Equivalent Isotropic Radiated Power (EIRP) and Gain to noise Temperature ratio (G/T) due to the stratospheric platform movements has been derived by calculating the deviation angle of the main beam directions between the earth station and the platform antenna. In this case, the antenna of the earth station has been assumed circular and/or patch array antennas.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1609-1614
• /
• 2003

In this study, a practical holographic interferometric tomography system, which is instantaneous and non-contact for measuring three dimensional flow field, was developed. The system consists of holographic recording/reconstruction system, fringe analysis code and computational tomography code and it is developed with Gill environment for general users. The developed system was applied to three-dimensional natural convection from a discrete flush-mounted circular heat source on the bottom of a cubic enclosure. The heat source was located at the off-center of the bottom plate so that three-dimensional temperature field can be achieved. A set of multi-directional holographic interferograms was recorded by employing a double-reference beam, double-exposure holographic technique. Optical pathlength data were extracted from the recorded interferometric data and finally three dimensional temperature field inside the cube was reconstructed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.10 s.103
• /
• pp.1186-1194
• /
• 2005

In this paper, we have systematically formulated the equations concerned to the in-plane and out-of-plane motions and deformations of a thick circular beam by using the kinetic and strain energies in order to analyse natural frequencies of a thick ring. The effects of variation of radius of curvature across the cross-section and also the effects of bending shear, extension and twist are considered. The equations of motion for natural vibration analysis of a ring are obtained utilizing the cyclic symmetry of vibration modes of the ring. The frequencies calculated using thick ring model and thin ring model are compared and discussed with the ones obtained from finite element analysis using the method of cyclic symmetry with 20-node hexahedral solid elements for rings with the different ratio of radial thickness to mean radius.

• Fire Science and Engineering
• /
• v.15 no.1
• /
• pp.41-46
• /
• 2001

The flow induced by a vertically impinging circular jet under a horizontal plate is investigated by visualization technique, using kerosene smoke in nitrogen gas to visualize the vortex flow and impinging flow. The light source was the sheet beam of Ar-Ion laser. The vertical and horizontal images scattering of kerosene smoke were recorded by the high speed CCD camera and the video camera. The instantaneous velocity of the vortex and the mean velocity of the smoke front were measured from the acquisited images.

• Structural Engineering and Mechanics
• /
• v.5 no.3
• /
• pp.283-295
• /
• 1997

This paper presents a high precision integration method for the dynamic response analysis of structures with holonomic constraints. A detail recursive scheme suitable for algebraic and differential equations (ADEs) which incorporates generalized forces is established. The matrix exponential involved in the scheme is calculated precisely using $2^N$ algorithm. The Taylor expansions of the nonlinear term concerned with state variables of the structure and the generalized constraint forces of the ADEs are derived and consequently, their particular integrals are obtained. The accuracy and effectiveness of the present method is demonstrated by two numerical examples, a plane truss with circular slot at its tip point and a slewing flexible cantilever beam which is currently interesting in optimal control of robot manipulators.

• Structural Engineering and Mechanics
• /
• v.48 no.2
• /
• pp.195-205
• /
• 2013

The buckling problem of linearly tapered micro-columns is investigated on the basis of modified strain gradient elasticity theory. Bernoulli-Euler beam theory is used to model the non-uniform micro column. Rayleigh-Ritz solution method is utilized to obtain the critical buckling loads of the tapered cantilever micro-columns for different taper ratios. Some comparative results for the cases of rectangular and circular cross-sections are presented in graphical and tabular form to show the differences between the results obtained by modified strain gradient elasticity theory and those achieved by modified couple stress and classical theories. From the results, it is observed that the differences between critical buckling loads achieved by classical and those predicted by non-classical theories are considerable for smaller values of the ratio of the micro-column thickness (or diameter) at its bottom end to the additional material length scale parameters and the differences also increase due to increasing of the taper ratio.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.5
• /
• pp.453-462
• /
• 2009

The differential quadrature method(DQM) is applied to the free in-plane vibration analysis of circular curved beams with varying cross-section neglecting transverse shearing deformation. Natural frequencies are calculated for the beams with various opening angles and end conditions. Results obtained by the DQM are compared with available results by other methods in the literature. It is found that the DQM gives good accuracy even with a small number of grid points. In addition, the corrected results are given for the beams not previously presented for this problem.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.459-466
• /
• 2005

In this paper, we have systematically formulated the equations concerned to the in-plane and out-of-plane motions and deformations of a thick circular beam by using the kinetic and strain energies in order to analyse natural frequencies of a thick ring. The effects of variation of radius of curvature across the cross-section and also the effects of bending shear, extension and twist are considered. The equations of motion for natural vibration analysis of a ring are obtained utilizing the cyclic symmetry of vibration modes of the ring. The frequencies calculated using thick ring model and thin ring model are compared and discussed with the ones obtained from finite element analysis using the method of cyclic symmetry with 20-node hexahedral solid elements for rings with the different ratio of radial thickness to mean radius.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.923-926
• /
• 2007

In this paper, the vibration of a rotating shaft with a thin rigid disk is considered. It is assumed that the shaft has uniform, circular cross-section. Based on the Timoshenko-beam theory, the transverse displacements and slops in two lateral directions, the axial displacement, and the torsional deformation are considered. A spectral element model is developed by using the variation method for the vibration analysis of the rotating shaft with a thin rigid disk, which is modeled by two shaft elements and a thin rigid disk element. The result of vibration analysis by finite element method is compared to the result of this research.