• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.624-629
• /
• 2003

In this paper, broadband shunt technique for increasing transmission loss is experimentally investigated. Piezoelectric shunt damping is studied using resonant shunt circuit and negative capacitor shunt circuit. A resonant shunt circuit is implemented by using a resistor and inductor. Negative Capacitor shunt damping is similar in nature to resonant shunt damping techniques, as a single piezoelectric material is used to dampen multi-mode. Performance of both methods is experimentally studied for noise reduction. This is based upon SAE J1400 test method and a transmission loss measurement system is provided for it. This paper will present the test setup fer transmission loss measurement and the tuning procedure of shunt circuits. Finally the results of sound transmission tests will be shown.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1276-1282
• /
• 2003

The SMT(Surface Mount Type) ferrite bead used to reduce the influx of power bus noise is modeled with parallel capacitor(C), series resistor(R) and series inductor(L). The simple equivalent circuit modeling doesn't agree with the measurement result. In this paper, we proposed the accurate equivalent circuit model of the ferrite bead at wide frequency range(50 MHz∼3 GHz) and analyzed the noise effect to the high speed IC(Integrate Circuit) with ferrite bead or not.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.12
• /
• pp.98-107
• /
• 1993

This paper describes a design of a multi-bit oversampling noise-shaping D/A converter which achieves a resolution of 12 bits using oversampling technique. In the architecture the essential block which determines the whole accuracy is the analog internal D/A converter, and the designed charge-integration internal D/A converter adopts a differential structure in order to minimize the reduction of the resolution due to process variation. As the proposed circuit is driven by signal clocks which contains the information of the data variation from the noise-shaping coder, it minimizes the disadvantage of a charge-integration circuit in the time axis. In order to verify the circuit, it was integrated with the active area of 950$\times$650${\mu}m^{2}$ in a double metal 1.5-$\mu$m CMOS process, and testified that it can achieve a S/N ratio of 75 dB and a S/(N+D) ratio of 60 dB for the signal bandwidth of 9.6 kHz by the measurement with a spectrum analyzer.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.493-498
• /
• 2004

The EMI noise source in a switching mode power supply is dominated by a common mode noise. If we can understand the common mode noise occurring mechanism, it is resulted to find out the method to suppress the EMI noise source in the switching mode power supply. The common mode noise is occurring mostly due to circuit is unbalanced which is caused by the capacitive coupling to frame ground, which passes through a heatsink of the switching devices. This research paper presents a new effective balancing method of buck converter circuit by mean of grounding the parasitic and compensation capacitors in correct proportion which is called that the common mode impedance balance (CMIB). The CMIB can be achieved by source, transmission line and termination balanced, such balancing, the common mode current will be cancelled out in the frame ground. The greatly reduced common mode noise can be confirmed by the experimental results.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.3
• /
• pp.125-135
• /
• 2009

An analytical 2-dimensional model to explain the small signal and noise properties of an AlGaN/GaN modulation doped field effect transistor has been developed. The model is based on the solution of two-dimensional Poisson's equation. The developed model explains the influence of Noise in ohmic region (Johnson noise or Thermal noise) as well as in saturated region (spontaneous generation of dipole layers in the saturated region). Small signal parameters are obtained and are used to calculate the different noise parameters. All the results have been compared with the experimental data and show an excellent agreement and the validity of our model.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.3
• /
• pp.6-11
• /
• 1977

The noise behavior of the Schottky Barrier Gate FET has been investigated by the use of noise equivalent circuit. It has been found that an additional noise source has to be taken into account in the GaAs SBGFET's biased in the pinch-off region; the intervalley scattering noise and the hot electron noise. In this paper, a noise equivalent circuit has been used to determine the noise parameter which was taken into account influence of the saturation velocity of carrier and parasitic resistance.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.533-534
• /
• 2007

This paper investigates impulsive noise from a pole transformer in low voltage distribution system for power line communication. EMI noise from the pole transformer is indicated from the experiment. The noise has certain characteristics because it is caused by partial discharge. The noise level is above -35dBm without a filter. Therefore, the filter which is made of ferrite is used in order to eliminate the noise. the noise filters should be applied to both the phase line and the neutral line. Otherwise, It is likely to have little overall impact on elimination of noises. the performance of filter is verified with various experiments. In conclusion, the equivalent circuit of power line communication including noise source is described as a lumped circuit.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1692-1695
• /
• 2007

We describe the image enhancement method of applying two spatial filters with different characteristics adaptively. An adaptive method is introduced so that sharpness enhancement is performed only in regions where the image exhibits significant dynamics, while noise reduction is achieved in smooth regions. Simulation results show that the proposed method improved the image quality.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.6
• /
• pp.16-23
• /
• 2003

In this paper, we propose an efficient bias circuit of discrete BJT component for hearing aid. The collector feedback bias circuit, widely used for the hearing aid, has a resistor for negative feedback. As the resistor affects AC and DC simultaneously, it is quite difficult to adjust amplifier gain without changing DC bias point. The previous bias circuit also has weak point to be oscillated by the positive feedback of power noise if gain of hearing aid is high. In the proposed circuit, we can reduce the two weak points of the previous circuit by adding a resistor to the collector feedback bias circuit between base and power supply which is $\beta$ times target than the collector resistor. Thus. we can change amplifier gain without changing DC bias point, and reduce power noise gain about 18.5% compare to that of tile previous circuit in the simulation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.1
• /
• pp.84-90
• /
• 2010

In this paper, a novel voltage-controlled oscillator (VCO) using the harmonic control circuit based on the composite right/left-handed (CRLH) transmission lines (TLs) is presented to reduce the phase noise without the reduction of the frequency tuning range and miniaturize the circuit size. The phase noise is reduced by the novel harmonic control circuit having the short impedances for the second- and third-harmonic components. The proposed harmonic control circuit is designed by using the CRLH TLs with the dual-band characteristic by the frequency offset and phase slope of the CRLH TLs. The high-Q resonator has been used to reduce the phase noise, but has the problem of the frequency tuning range reduction. However, the frequency tuning range of the proposed VCO has not been reduced because the phase noise has been reduced without the high-Q resonator. The miniaturization of the circuit size is achieved by using the CRLH TLs instead of the conventional right-handed (RH) TLs. The phase noise of VCO is -119.17 ~ -117.50 dBc/Hz at 100 kHz in the tuning range of 5.731 ~ 5.938 GHz.