• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.913-916
• /
• 2003

In many cases, ac line EMI filters are designed by trial and error method. Thus, designing a filter is a time-consuming process. To overcome the problem, the newly analytical design procedure is proposed in this paper. Using the modeling circuit of each filter components, the filter design is carried out applicable to both common-mode (CM) and differential-mode (DM). These are verified through the experimental results.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.4
• /
• pp.75-79
• /
• 2013

A power distribution network (PDN) is a network that provides connection between the voltage source supply and the power/ground terminals of a microprocessor chip. It consists of a voltage regulator module, a printed circuit board, a package substrate, a microprocessor chip as well as decoupling capacitors. For power integrity analysis, the board and package layouts have to be transformed into an electrical network of resistor, inductor and capacitor components which may be expressed using the S-parameters models. This modeling process generally takes from several hours up to a few days for a complete board or package layout. When the board and package layouts change, they need to be re-extracted and the S-parameters models also need to be re-generated for power integrity assessment. This not only consumes a lot of resources such as time and manpower, the task of PDN modeling is also tedious and mundane. In this paper, a block-based PDN modeling is proposed. Here, the board or package layout is partitioned into sub-blocks and each of them is modeled independently. In the event of a change in power rails routing, only the affected sub-blocks will be reextracted and re-modeled. Simulation results show that the proposed block-based PDN modeling not only can save at least 75% of processing time but it can, at the same time, keep the modeling accuracy on par with the traditional PDN modeling methodology.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.8
• /
• pp.798-804
• /
• 2013

In this paper, conducted emission from the LDC(Low-Side DC/DC Converter) of a HEV/EV was analyzed using high-frequency circuit modeling in system-level approach. The conducted emission by PWM process(100 kHz; Switching Frequency) can cause RFI(Radio-Frequency Interference) problems in the AM/FM frequency range. In order to mitigate this conducted emission, a high-frequency equivalent circuit model is proposed by analyzing the fundamental circuits, parasitic components in their parts and connections and non-linear characteristics of MOSFETs, high-power capacitors, inverters, motors, high-power cables, and bus bars which are composed of the LDC. Using these circuit models, results of both simulation and measurement were compared and similarities between them were verified. We are looking forward that this approach can be effectively used in the EMC design of HEV/EV.

• Journal of Power Electronics
• /
• v.11 no.5
• /
• pp.759-766
• /
• 2011

This paper focuses on monitoring and predicting the short circuit faults of the rotor windings of large turbo-generator systems. For the purpose of increasing efficiency and decreasing maintenance cost, a method that combines the HHT (Hilbert Huang Transform) with a wavelet has been studied. This method is based on analyzing a classical Albright detecting coil. Due to the Empirical Mode Decomposition (EMD) and the Intrinsic Mode Functions (IMF) of the HHT the exact location of a short circuit of rotor windings may be given. However, a part of the useful information is eliminated by the unreasonable decomposing scale of the wavelet. Based on the thermodynamics modeling method, this study was illustrated with a 50MW turbo-generator system that is installed in Northern China. The analysis results, which have very good agreement with those of a previous study, show that the method of combining the HHT with a wavelet is an effective way to analyze and predict the short circuit faults of the rotor windings of large generators, such as supercritical turbo-generator systems and wind turbo-generator systems. This work can offer a useful reference for analyzing smart grids by improving the power quality of a distribution network that is supplied by a turbo-generator system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.6
• /
• pp.745-752
• /
• 2018

ICs(Integrated circuits) for nuclear power plant exposed to radiation environment occur malfunctions and data errors by the TID(Total ionizing dose) effects among radiation-damage phenomenons. In order to protect ICs from the TID effects, this paper proposes a radiation-hardening of the logic circuit(D-latch) which used for the data synchronization and the clock division in the ICs design. The radiation-hardening technology in the logic device(NAND) that constitutes the proposed RH(Radiation-hardened) D-latch is structurally more advantageous than the conventional technologies in that it keeps the device characteristics of the commercial process. Because of this, the unit cell based design of the RH logic device is possible, which makes it easier to design RH ICs, including digital logic circuits, and reduce the time and cost required in RH circuit design. In this paper, we design and modeling the structure of RH D-latch based on commercial $0.35{\mu}m$ CMOS process using Silvaco's TCAD 3D tool. As a result of verifying the radiation characteristics by applying the radiation-damage M&S (Modeling&Simulation) technique, we have confirmed the radiation-damage of the standard D-latch and the RH performance of the proposed D-latch by the TID effects.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.6
• /
• pp.7-12
• /
• 2010

A semi-empirical organic schottky diode model is proposed for circuit simulation. We have set up a full custom design environment for organic schottky diode circuit using Spectre AHDL, which is widely used commercial EDA tool. We measured frequency response from fabricated rectifier, and it was compared to circuit simulation results using the AHDL model. The frequency response of the fabricated rectifier circuit is not sufficient for 13.56MHz RFID, however, it is enough for 135kHz-band RFID.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.2
• /
• pp.168-176
• /
• 2015

Due to the reduction in device feature size, transient faults (soft errors) in logic circuits induced by radiations increase dramatically. Many researches have been done in modeling and analyzing the susceptibility of sequential circuit elements caused by soft errors. However, to the best knowledge of the authors, there is no work which has well considerated the feedback characteristics and the multiple clock cycles of sequential circuits. In this paper, we present a new method for evaluating the susceptibility of sequential circuit elements to soft errors. The proposed method uses four Error Propagation Probability Matrixs (EPPMs) to represent the error propagation probability of logic gates and flip-flops in current clock cycle. Based on the predefined matrix union operations, the susceptibility of circuit elements in multiple clock cycles can be evaluated. Experimental results on ISCAS'89 benchmark circuits show that our method is more accurate and efficient than previous methods.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.169-175
• /
• 2013

CRDi technology of diesel engine was developed from in the early 2000s due to a need to increase fuel efficiency and environment care. Especially, high-pressure fuel injection system in CRDi system which has a fuel injection unit including an injector, a fuel pump and common-rail, etc. becomes possible to make the exhaust gas clean as well as power improvement. In this study, comparison of dynamic characteristics of servo-hydraulic piezo-driven injector with 3-way and bypass-circuit type was analyzed by using the AMESim code. As results of this study, it found the bypass-circuit inside servo-hydraulic piezo injector can cause a faster injection response than that of the 3-way type. Also it was shown that bypass-circuit type had better control capability due to hydraulic bypass system.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.1897-1902
• /
• 2008

The computer system is used in many application domains and any system error in these domains may either cause critical loss or threaten environment or human life. Though examples of these domains can be found in many areas, the system, which is used in domains for carrying passengers including rolling stocks in particular, is expected to show satisfactory operation all the time. The relay control logic, which is used in rolling stocks, is complex in hardware and occupies considerably large volume. Nevertheless, it has been used for a long time, to let the system safely operate even in the occurrence of an error in the computer system. However, the relay control logic circuit is so complex that the analysis of proper circuit operation and interlocking tends to be dependent only on the designer's experiences instead of being systematically performed. Especially, the analysis following a change, addition and deletion of a previous circuit according to the requirements from a source of demand is significantly limited. In this paper, the accuracy of relay control logic is verified by the use of properties of Petri Net model. In addition, how main circuit breaker (MCB) control circuit is modeled and analyzed by the design methodology is shown.

• Journal of the Korean Magnetics Society
• /
• v.2 no.1
• /
• pp.69-74
• /
• 1992

This paper describes the energy and speed characteristics of an induction coil-gun. The coil-gun has some merits that it can be easily installed and repeatedly used many times, it does not damage mechanically in the course of launch and the force exerted on the projectile is distributed uniformly. An equivalent circuit is employed for modeling the coil-gun. The circuit equations and equation of motion are then derived based on the equivalent circuit. These equations are solved numerically by using Runge-Kutta method. Finally the energy transfer ratios are obtained according to the variations of the resonant frequency of driving circuit and charging voltage of capacitors. The muzzle velocities of projectile are also obtained according to the variations of electrical conductivity and initial position of projectile, firing angle of driving circuit, charging voltage of capacitor and resistance of driving coil, respectively.