• 한국전자통신학회논문지
• /
• 제5권1호
• /
• pp.17-22
• /
• 2010

일반적으로 카오스 회로에는 Chua's 회로, Lorenz 회로, Duffing 회로 등이 있다. 이들 카오스 회로 중에서 Chua's 회로가 전자부품을 이용하여 가장 쉽게 구성할 수 있는 회로로 알려져 있다. Chua's 회로는 일반적으로 저항성분인 R, 인턱터 성분인 L, 캐패시터 성분인 C로 구성하는 선형요소와 비선형 저항으로 구성하는 비선형 요소로 구성된다. 그러나 L 요소는 포화특성으로 인하여 시중에서 구입한 부품으로는 실제 하드웨어를 구현하기 어려운 문제점이 있다. 본 연구에서는 Chua 회로의 선형 요소인 R,L,C 성분의 요소 중에서 포화 특성을 자지고 있어 상용화된 제품으로는 제작 구현이 어려운 L 성분을 C 성분으로 대체하는 간략화한 Chua's 회로 제작 기법을 PSpice로 해석하고, 그 결과를 확인한다.

• Journal of Welding and Joining
• /
• 제23권5호
• /
• pp.14-19
• /
• 2005

In high speed $CO_2$ welding, it has been blown to produce no sound bead with undercut or humping bead. In this study welding phenomena through synchronized high speed camera and output welding voltage and current waveform has been analyzed. For the purpose to improve a welding bead, effect of short circuit current rise slope has been examined. With commercial power source it was produced no sound bead by instantaneous short circuit, long arc period and stubbing at welding speed 2.5mm/min Humping bead or undercut were showed by instantaneous short circuit and long arc period. Also, the weld bead was not formed during the long short circuit period after stubbing start and long arc extinguishment period after wire sticking by failure of arc regeneration, because the droplet was not transferred to weld pool. With increasing short circuit current rise slope the frequency of stubbing was decreased and the normal short circuit rate was increased. A control of short circuit current rise slope was effective factor in high speed welding.

• Journal of Welding and Joining
• /
• 제16권3호
• /
• pp.95-101
• /
• 1998

Waveforms of $CO_2$ gas shielded arc welding in short circuit transfer mode was studied with the waveform analysis program, which can calculate various waveform factors such as number of short circuit event, mean and standard deviation of short circuit time and arc time. The calculated values of these factors were correlated independently or in combination with the spatter generation rate to figure out the most reliable index for evaluating spatter generation and further for arc stability. As a result this study, it was confirmed that the spatter generation tends to decrease with the increase of short circuit frequency. Further to this, it was also found that as the short circuit frequency increases the short circuit event becomes more uniform resulting in the decrease of standard deviations ($\sigma$values) of short circuit time and arc time. This result demonstrated that these factors are strongly correlated with each other and thus any one of these factors can be used for the evaluation index. In the discussion, however, short circuit frequency was proposed for the most practical index in evaluating the arc stability of short circuit transfer mode since it is the one which could be monitored in-process condition without any complex caculation process.

• 전력전자학회논문지
• /
• 제26권3호
• /
• pp.176-182
• /
• 2021

This research proposes a high-frequency circuit that can accurately predict the differential mode noise of single-phase inverters at the circuit design stage. Proposed single-phase inverter high frequency circuit in the work is a form in which harmonic impedance components are added to the basic single-phase inverter circuit configuration. For accurate noise prediction, parasitic components present in each part of the differential noise path were extracted. Impedance was extracted using a network analyzer and Q3D in the measurement range of 150 kHz to 30 MHz. A high-frequency circuit model was completed by applying the measured values. Simulations and experiments were conducted to confirm the validity of the high-frequency circuit. As a result, we were able to predict the resonance point of the differential mode voltage extracted as an experimental value with a high-frequency circuit model within an approximately 10% error. Through this outcome, we could verify that differential mode noise can be accurately predicted using the proposed model of the high-frequency circuit without a separate test bench for noise measurement.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.650-652
• /
• 2001

The permanent magnet in hybrid step motor is magnetized to the axial direction. Accordingly the 2D analysis method such as 2D finite element method cannot guarantee the analysis accuracy. In this paper, the characteristics of hybrid type step motor are analyzed by using 3D equivalent magnetic circuit network method(3D EMCNM). 3D EMCNM supplements magnetic equivalent circuit by numerical technique using distributive magnetic circuit parameter and 3D EMCNM is used for the accurate and efficient analysis. The validity of the analysis results is confirmed by comparing with the experimental ones.

• 전기학회논문지
• /
• 제59권5호
• /
• pp.860-865
• /
• 2010

When a circuit breaker is opened, a large capacitance around the buses, the circuit breaker and the potential transformer (PT) might cause PT ferroresonance. During PT ferroresonance, the iron core repeats saturation and unsaturation even though the supplied voltage is a rated voltage. This paper describes an analytical analysis of PT ferroresonance in the transient-state. To analyze ferroresonance analytically, the iron core is modelled by a simplified two-segment core model in this paper. Thus, a nonlinear ordinary differential equation (ODE) for the flux linkage is changed into a linear ODE with constant coefficients, which enables an analytical analysis. In this simplified model, each state, which is either saturated or unsaturated state, corresponds to one of the three modes, i.e. overdamping, critical damping and underdamping. The flux linkage and the voltage in each state are obtained analytically by solving the linear ODE with constant coefficients. The proposed transient analysis is effective in the more understanding of ferroresonance and thus can be used to design a ferroresonance prevention or suppression circuit of a PT.

• 대한전기학회논문지:전력기술부문A
• /
• 제51권8호
• /
• pp.409-416
• /
• 2002

This paper presents a fault location algorithm using direct 3-phase circuit analysis for distribution power networks. The unbalanced feature of distribution networks due to single phase loads or asymmetric operation prohibits us from using the conventional symmetrical component transformation. Even though the symmetrical component transformation provides us with a very easy tool in three phase network analysis, it is limited to balanced systems in utilizing its strong point, which is not suitable for distribution networks. In this paper, a fault location algorithm using direct 3-phase circuit analysis is developed. The algorithm is derived and it Is shown that the proposed method if we use matrix inverse lemma, is not more difficult then the conventional methods using symmetrical component transformation. Since the symmetrical component transformation is not used in the suggested method, unbalanced networks also can be handled with the same difficulty as balanced networks. The case study results show the correctness and effectiveness of the proposed algorithm.

• 전자공학회논문지 IE
• /
• 제49권2호
• /
• pp.52-57
• /
• 2012

사회발전과 더불어 가전기기의 발전은 누전으로 인한 감전, 화재 등 여러 가지 누전전류의 위험성에 노출되어 있다. 가정 내 배전함에 누전차단기가 설치되어 있지만, 기존의 누전차단기는 배전함에 설치되어 누전시 전원을 차단해주는 기능만을 갖는다. 또한 집안 벽마다 설치된 콘센트에 연결된 가전기기들을 개별적으로 점검하는 일은 쉬운 일이 아니다. 따라서 본 논문에서는 누전차단기회로의 성능 및 회로를 분석하고, ZigBee기반의 센서를 이용하여 가정 내 가전기기들의 누전상태를 모니터링 할 수 있는 방법에 대해 제시하였다. 성능분석 결과, 제안된 ELB 누전전류 제어시스템은 가전기기에 내장된 누전차단기 회로를 응용했기 때문에 각각의 가전기기들의 누전상태를 확인할 수 있어 기존 시스템 보다 누전을 쉽고 편리하게 모니터링 할 수 있을 것이라 기대한다.

• 전기학회논문지
• /
• 제63권4호
• /
• pp.490-494
• /
• 2014

In this paper, a design of high-speed power-off circuit and analysis. The incidence of high-dose transient radiation into the silicon-based semiconductor element induces the photocurrent due to the creation of electron-hole pairs, which causes the upset phenomenon of active elements or triggers the parasitic thyristor in the element, resulting in latch-up. High speed power-off circuit was designed to prevent burn-out of electronic device caused by Latch-up. The proposed high speed power-off circuit was configured with the darlington transistor and photocoupler so that the power was interrupted and recovered without the need for an additional circuit, in order to improve the existing problem of SCR off when using the thyristor. The discharge speed of the high speed power interruption circuit was measured to be 19 ${\mu}s$ with 10 ${\mu}F$ and 500 ${\Omega}$ load, which was 98% shorter than before (12.8 ms).

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권1호
• /
• pp.34-38
• /
• 2005

The finite element method is very flexible for new shapes and provides flux distribution, magnetomotive force, eddy currents, and torques. However, it requires lengthy computational time in order to achieve desired accuracy. The magnetic equivalent circuit method takes less computation time than the finite element method. Therefore, the finite element method is mainly used to confirm the completed design. The magnetic equivalent circuit method is convenient for complicated analysis of the transient state of the induction motor. The magnetic equivalent circuit method is restricted to only one direction of magnetic flux. In this paper, the construction elements (that is, stator iron, rotor iron, yoke, air gap, etc.) of the squirrel cage induction motor were represented by a flux tube and the air gap magnetomotive force was calculated by the magnetic equivalent circuit method. Starting transient torque and phase current of the squirrel cage induction motor were verified by the theoretical calculation and the experiment.