• Journal of the Korean Solar Energy Society
• /
• v.27 no.2
• /
• pp.37-44
• /
• 2007

As photovoltaic(PV) power generation system becomes more common, it will be necessary to investigate islanding detection method for PV systems. Islanding of PV systems can cause a variety of problems and must be prevented. However, if the real and reactive power of the load and PV system are closely matched, islanding detection by Passive methods becomes difficult. Also, most active methods lose effectiveness when there are several PV systems feeding the same island. The active frequency drift positive feedback method(AFDPF) enables islanding detection by forcing the frequency of the voltage in the island to drift up or down. In this paper the research for the minimum value of chopping fraction gain applied digital phase-locked-loop (DPLL) to AFDPF considering output power quality and islanding prevention performance are performed by simulation and experiment according to IEEE Std 929-2000 islanding test.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.800-811
• /
• 2018

This paper presents a regenerative braking control scheme for Switched Reluctance Machine (SRM) drive in Electric Vehicles (EVs). The main purpose is to maximize the recovered energy during battery charging by taking into account the nonlinear physical characteristics of the Switched Reluctance Machine. The proposed regenerative braking method employs the back-EMF in the generation process as a complicated position-dependent voltage source. The proposed maximum power recovery (MPR) operation of the regenerative braking is first based on the maximization of the extracted power from the machine and then the maximization of the power transferred to the battery. The maximum power extraction (MPE) from SRM is based on maximizing the energy conversion ratio by the calculation of the optimum PWM switching duty cycle, turn-on, and turn-off angles. By using the impedance matching theorem that allows the maximum power transfer (MPT) of the MPE, the proposed MPR is achieved. The parametric averaged value modeling of the machine phase currents in the chopping control mode is used for MPR realization. By following this model, a nonlinear equivalent input resistance is derived for the battery internal resistance matching. The effectiveness of the proposed regenerative braking method is demonstrated through simulation results and experimental implementation.

• ETRI Journal
• /
• v.33 no.6
• /
• pp.897-903
• /
• 2011

A hybrid ${\Delta}{\Sigma}$ modulator for audio applications is presented in this paper. The pulse generator for digital-to-analog converter alleviates the requirement of the external clock jitter and calibrates the coefficient variation due to a process shift and temperature changes. The input resistor network in the first integrator offers a gain control function in a dB-linear fashion. Also, careful chopper stabilization implementation using return-to-zero scheme in the first continuous-time integrator minimizes both the influence of flicker noise and inflow noise due to chopping. The chip is implemented in a 0.13 ${\mu}m$ CMOS technology (I/O devices) and occupies an active area of 0.37 $mm^2$. The ${\Delta}{\Sigma}$ modulator achieves a dynamic range (A-weighted) of 97.8 dB and a peak signal-to-noise-plus-distortion ratio of 90.0 dB over an audio bandwidth of 20 kHz with a 4.4 mW power consumption from 3.3 V. Also, the gain of the modulator is controlled from -9.5 dB to 8.5 dB, and the performance of the modulator is maintained up to 5 nsRMS external clock jitter.

• Korean journal of food and cookery science
• /
• v.19 no.5
• /
• pp.647-658
• /
• 2003

Foodservice at elementary schools has been provided nation-wide. It is predictable that foodborne diseases would increase continuously. Formation of a counterplan is urgently needed. This study was designed to identify the stage which contains the critical control points (CCPs) for the microbiological management of HACCP (Hazard Analysis Critical Control Point) at the foodservice provided at elementary schools. Foodservice places at four elementary schools in Seoul were sampled and the overall hygiene of cooking, utensils and equipment, employees, and environment by season were examined. The results showed that the number of bacteria in overall samples was increased and that E. coli, Salmonella and Staphylococcus by biochemical test emerged in more diverse samples in summer than in spring. Particularly, the number of aerial bacteria in summer was three-fold greater than that in either spring or winter. E. coli 0157 was not detected, although Salmonella was identified by PCR analysis in the meat knives, chopping boards, waste bins and meat dish at elementary school foodservice. According to this data, cross-contamination should be managed in the stage of mixing up the ingredients with improper equipments and insanitary treatments. Thus, the establishment of SSOP (Sanitation Standard Operating Procedures) and GMP (Good Manufacturing Practice) at elementary school foodservice is stringently required, along with sanitation education for workers and employees as CCPs.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.105-108
• /
• 2001

This paper compared a Modified C-dump converter and energy efficient converter topologies, derived from the conventional C-dump converter, for switched reluctance motor (SRM) drives. The proposed topologies overcome the limitations of the conventional C-dump converter, and could reduce the whole cost of the SRM drive. Also, the above converters have simple control requirements; and allow the motor phase current to freewheel during chopping mode. Specially, the voltage ratings of the dump capacitor and some of the switching devices in the proposed an Energy efficient C-dump converter is reduced to the supply voltage ($V_{dc}$) level compared to twice the supply voltage ($2V_{dc}$) in the conventional C-dump converter. Simulation and experimental results of the proposed converters are presented and verified.

• Journal of Advanced Marine Engineering and Technology
• /
• v.13 no.1
• /
• pp.57-68
• /
• 1989

This paper treats the analytical and experimental studies on the improvement of commutating circuit for the speed control of DC motor. A simple circuit composed of R, L and C elements is proposed here for switching off power SCR carrying the load current. The real important in this chopper circuit is to determine the reasonable values of commutating circuit constants. In this paper, the reasonable values of the commutating circuit constants are basically determined on a view point of commutating performances in the given circuit model and must satisfy the following conditions. The first, the peak commutating current should be larger than the anticipated maximum load current. The second, the circuit turn-off time (tc) must be longer than the SCR turn-off time (tq). The third, the resistor should be enough large to permit the current to be neglected in the analysis of the commutation circuit, as well as be enough small to permit to charge the capacity voltage (Ec) to the half the value of source voltage (E) before the next communication cycle is initiated. The last, the period of chopping signal must be the least possible multiple of the damping vibration period of commutating circuit. The improved chopper circuit used in the experiment under unloaded condition was composed to meet the reasonable conditions mentioned above, and a successful commuting performance was achieved without failure. Several types of microprocessor having a different value of CPU speed individually have been applied to the experiment under the loaded conditions. Also it shows that the faster the speed of CPU is, the more stable the commutation turns out.

• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1166-1177
• /
• 2014

A new type of topology with medium-frequency-transformer (MFT) isolation for medium voltage wind power generation systems is proposed in this paper. This type of converter is a high density power conversion system, with high performance features suitable for next generation wind power systems in either on-shore or off-shore applications. The proposed topology employs single-phase cascaded multi-level AC-AC converters on the grid side and three phase matrix converters on the generator side, which are interfaced by medium frequency transformers. This avoids DC-Link electrolytic capacitors and/or resonant L-C components in the power flow path thereby improving the power density and system reliability. Several configurations are given to fit different applications. The modulation and control strategy has been detailed. As two important part of the whole system, a novel single phase AC-AC converter topology with its reliable six-step switching technique and a novel symmetrical 11-segment modulation strategy for two stage matrix converter (TSMC) is proposed at the special situation of medium frequency chopping. The validity of the proposed concept has been verified by simulation results and experiment waveforms from a scaled down laboratory prototype.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.3
• /
• pp.171-178
• /
• 1987

A study of two phase chopper system with four separate groups of DC motors in powering. A novel two phase chopper system with four separate groups of DC motors which applies the principles of two phase chopper with two separate groups of DC motors is dealt with this article. The main circuit consists of eight sets of chopping parts, four diodes and four separate groups of DC motors. Four groups of DC motors are driven through the series and parallel connections to each other in accordance with the operating conditions of the choppers. Although the proposed chopper circuit requires more circuit elements than the conventional two phase chopper system with combined output or two phase chopper system with two separate groups of DC motors, it has the following advantages` (1). It is possible to drive twice as much motors as conventional system does, using esisting receiving-and equipments and motors. (2). It is possible to control load voltage continuously from 0 to source voltage by changing time-ratio from 0 to 1. (3). Load current division becomes equalized. Therefore it is possible to drive not only series motors but also shunt and separately exited motors. (4). When smoothing reactor L is small, harmonic components of the proposed circuit is not so large. Therefore, the value of L can be determined from viewpoints of allowable value of ripple-ratio and current unbalance factor.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.2
• /
• pp.123-128
• /
• 2022

The torque of the SRM((Switched Reluctance Motor)) is proportional to the inductance slope, so it has a non-linear torque characteristic, and has a disadvantage in that the torque pulsation is large and noise is severe. In particular, the biggest obstacle to the commercialization of SRM is the pulsating torque generated from the rotating shaft, which has various adverse effects not only on the device itself but also on the peripheral devices. Therefore, various methods for reducing the pulsating torque have been published by domestic and foreign researchers, and there is a study result that the hysteresis controller has an advantage in that it can flow a smooth current compared to the chopping control. However, in determining the hysteresis band, if the band is too small, it has a disadvantage in that it may cause a switching loss due to many switching and an unstable initial start when the encoder is used. Therefore, in this paper, a variable hysteresis controller that can reduce torque ripple in a steady state while having a more stable and fast speed response through the change of the hysteresis band according to the speed error.

• Journal of the FoodService Safety
• /
• v.2 no.2
• /
• pp.97-102
• /
• 2021

The purpose of this study was to investigate the effect of developing and continuously providing on-line hygiene education programs on the improvement of hygiene conditions in children's cafeterias. As a result of the 2020 sanitation and safety checklist analysis, 6 items (personal hygiene, separate use, clean ventilation, temperature control of refrigerators, country of origin, food distribution) were derived and on-line hygiene education programs for each of 6 items were produced. ① Customized educational materials and self-inspection checklists were provided to 208 children's cafeterias. After that, educational videos were provided through Kakao Talk twice a week for 6 months, and they were made available for viewing at any time through YouTube upload, ③ Kakao Talk Through this, a quiz related to the educational video was conducted to give feedback for interaction with the cook. As a result of analyzing the total hygiene and safety checklist score of all registered facility catering centers by visit order, in 2020 it was 82.8 points/100 points, but in 2021, it was 84.2 points (1st round), 89.3 points (2nd round), 91.4 points (3 points) The score improved significantly (p<0.001) as the on-line hygiene education program continued. As a result, significant (p<0.001) changes were observed in the items of 'Knife, chopping board' and 'Sanitation clothes, sanitary hat, sanitary shoes, apron, and sanitary gloves', confirming a clear improvement effect. Therefore, it is considered that the on-line hygiene education program will play a positive role in showing a lasting effect on improving hygiene management in children's cafeterias.