• The Journal of the Acoustical Society of Korea
• /
• v.16 no.2
• /
• pp.5-9
• /
• 1997

In this paper, when we use the chirp signal as input signal of ultrasonic signal system the technique for determining the bandwidth of the chirp signal that maximizes the amplitude of the compressed ultrasonic echo signal has been studied. In ultrasonic signal processing systems, the signal-to-noise ratio of the echo signal can be too low due to damping and scattering of the ultrasonic wave during transmission. Method of pulse compression using chirp signal is a means to increase the signal-to-noise ratio in ultrasonic pulse-echo systems. Simulation and experimental results showed that the output signal of ultrasonic system was increased by pulse width of chirp signal and the optimum-bandwidth of the chirp signal was 1.15 times larger than the bandwidth of the ultrasonic system.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.3
• /
• pp.658-665
• /
• 2013

While the chirp signal is extensively used in radar and sonar systems for target decision in wireless communication systems, it has not been widely used for positioning in indoor environments. Recently, the IEEE 802.15.4a standard has adopted the chirp spread spectrum (CSS) as an underlying technique for low-power and low-complexity precise localization. Chirp signal based ranging solutions have been established and deployed but their ranging performance has not been analyzed in multipath environments. This paper presents a ranging performance analysis of a chirp signal and suggests a method to suppress multipath error by using a type of non-linear chirp signal. Multipath ranging performance is evaluated using a conventional linear chirp signal and the proposed non-linear chirp signal. We verify the feasibility of both methods using two-ray multipath model simulation. Our results demonstrate that the proposed non-linear chirp signal can successfully suppress the multipath error.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.127-128
• /
• 2006

In this paper, we propose a novel signaling method using chirp signals in UWB radio with satisfaction of FCC regulation. Chirp signals have been used in many ranging systems such as radar because of its good correlation properties. Because it is important to use broader signal bandwidth in order to get higher precision of the ranging, according to the Cramer-Rao Lower Bound, UWB radio is extremely good as the ranging systems. But, it is very difficult to apply existing chirp signals to UWB, because FCC regulates that the systems operating in UWB radio must occupy signal bandwidth more than 500MHz on the condition of stopping the frequency sweeping. So, we propose multiple chirp signals which can satisfy the regulation of FCC while maintaining chirp signal's properties. The multiple chirp signals which are composed of the sub-chirps modulated by sub-carriers can expand the signal bandwidth with the same principle of OFDM systems. The simulation results show that the BER performance of the proposed multiple chirp signals is identical to that of conventional OFDM when it is applied to data communication, and that the correlation properties of the proposed signals are almost the same with properties as those of single chirp signals whose sweeping bandwidth is the same value with the proposed one.

• Journal of Satellite, Information and Communications
• /
• v.8 no.2
• /
• pp.88-93
• /
• 2013

The wideband chirp signal generator to enhance the resolution of synthetic aperture radar of obtaining the earth observation image is needed. This paper deals with designing, manufacturing and testing the wideband digital chirp signal generator having high resolution for LEO earth observation satellite. The wideband digital chirp signal generator is implemented with the memory-map based structure which is mostly applied in the satellite, and consists of the digital module to generate the digital chirp signal and the RF module to perform the quadrature modulation. The I/Q signals stored in the memory of the digital module are D/A converted and delivered to be quadrature modulated with the reference signal of 1275 MHz in the RF module. Furthermore, the test bench and GUI to validate the signal generator function are also developed. It is found that the requirement of 144 MHz bandwidth for the digital chirp signal generator is well met. Finally it is noteworthy that the distortion occurred in the chirp signal generator was compensated by the pre-distortion compensation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.6
• /
• pp.906-911
• /
• 2001

In this paper, LPI(low probability of intercept) and AJ(anti jamming) performance of the chirped BPSK system are analyzed. In the chirp method the cyclostationary of the signal is eliminated, since the instantaneous frequency is varied randomly within the whole spread bandwidth. Therefore, chirp method is considered for good LPI system against DAM(delay-and-multiplier) or SC (squaring circuit) interceptor which detects the chip rate or carrier frequency. Longer chirp duration makes the LPI performance better. From the simulation results, the chirp method has better AJ performance than DS(direct sequence) system in the PBNJ(partial band noise jammer) channel. At the same JSR(jammer to signal power ratio) level, chirped BPSK system has more robust AJ performance against MTJ(multi-tone jammer) than PBNJ.

• The Journal of the Acoustical Society of Korea
• /
• v.27 no.2
• /
• pp.87-91
• /
• 2008

In this paper, the adaptive chirp beamforming method is proposed to solve the bias problem in the direction-of-arrivals (DOAs) estimation of the wideband chirp signals which have an identical time-frequency parameter and are emanated from different directions. The source location bias results from the interferences impinging on the array from the other directions. The proposed method exploits the time-frequency structure of the chirp signal based on STMV (STeered Minimum Valiance) to improve the DOA estimation performance by minimizing the chirp interferences effectively. Simulation results show the DOA estimation performance achieved by the proposed method as compared to the conventional methods.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.11
• /
• pp.1186-1193
• /
• 2009

In this paper, we propose DDS(Direct Digital Synthesizer) as a new implementation method of chirp LO(Local Oscillator) for compressive receiver applied for RFID signal detection in UHF band. We designed a receiver whose input frequency range is 908.5~914 MHz, DDL(Dispersive Delay Line) bandwidth is 6 MHz, and dispersion delay time is $13\;{\mu}s$. Chirp LO based on DDS is designed to meet $26\;{\mu}s$ sweep time and 12 MHz bandwidth for complete compressive mechanism. The measured 3 dB pulse width of the compressed signal of the fabricated receiver is 260 ns and the frequency resolution for simultaneous input signals is below 200 kHz. These performances indicate that the proposed chirp LO based on DDS and the compressive receiver is suitable for RFID signal detection in UHF band.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.1
• /
• pp.1-7
• /
• 2003

A recent technology trends in synthetic aperture radar(SAR) requires the ultra high resolution performance in detecting and precisely identifying the targets. In this paper, as a technique for enhancing the radar range resolution, the wideband chirp connection algorithm is presented by stitching the several chirp modules with unit bandwidth based on the linear frequency modulated chirp signal waveform. The principles of the digital chirp signal generation and its architecture for implementation is briefly described, and the wideband chirp signal generator, modulator, and demodulator are designed. The performance analysis for the presented algorithm is given with the simulation results.

• The Journal of Information Technology
• /
• v.7 no.3
• /
• pp.37-45
• /
• 2004

The representative communication method which is applied in the low-speed power line communication modem with 60bps is single carrier method. It has been used mainly for the control. The single carrier method is very sensitive to a power line communication channel environment. Specially, the severe attenuation of the transmission signal according to the notch characteristics of channel becomes the main cause of communication error. Domestic power line channel environment has this notable feature. In this paper, we implemented the low-speed power line communication system which used the chirp signal method to be strong in notch and noise characteristics. In this research, we proposed the method which transmits 1- '1 Unit symbol Chirp signal' with a 100${\mu}s$ time within 1ms for 1 bit. Also it applied for the Convolution code for an error correction and the Manchester code for a collision perception and an error detection. It used the method which uses the bit correlator for signal detection in the receiver parts. We confirmed that the communication method of the chirp method has a excellent performance compared to single carrier methods with a result of experiment of the low-speed power line communication system with the 60bps.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.2
• /
• pp.138-141
• /
• 2018

In this paper, we describe the designed digital waveform of a linear frequency-modulated (FM) chirp signal using field-programmable gate arrays (FPGAs) for image radar, and this signal is modulated with an I-Q modulator, and multiplied by 24 frequency multipliers to obtain a 94-GHz W-band wideband chirp generator. The developed chirp generator is an FM signal with a 94-GHz carrier frequency and a 960-MHz bandwidth, and the flatness is less than 1.0 dB at intermediate frequency (IF) (3.9 GHz), 2.0 dB in the W-band, and it has a 0.3-W output power in the W-band.