• Journal of agriculture & life science
• /
• v.52 no.6
• /
• pp.81-88
• /
• 2018

This study analyzed the characteristics of 6 recyclable bulking agents which can replace sawdust and rice hulls that are commonly used in livestock manure composting. The content of all the hazardous chemicals found in the bulking agents used in this experiment was between 0.0 and 34.1 ppm, which was noticeably lesser than the maximum content levels of hazardous substances 5.0~900.0 ppm prescribed by the Rural Development Administration(RDA), which means that the bulking agents would be able to replace sawdusts and rice husks. The water content of the bulking agents ranged from a minimum of 12.4% to a maximum of 16.6% in the original state, which was much less than 60%, the optimal moisture content. These results indicate that they would be able to function fully as bulking agents. Their water absorption rate was in the range of minimum 31.9% ~ maximum 600.0%, which showed huge differences among the types of bulking agents. The most appropriate bulking agent in terms of water absorption rate was wood pellets. It was the highest in the wood briquette manufactured by A, which was followed by C and B in the order. The shear strength of the 5 types of bulking agents in the original state was 271.7 N on an average, the highest figure of all, except for the oak briquette whose shear strength could not be measured and the wood pellets in the absorption state. The shear strength in the dry and absorption states then followed, and were 78.0 N and 27.7 N on an average, respectively. The wood briquette of A recorded considerably lower shear strength than that of B and C. Overall, shear strength tended to increase according to lower water absorption rates. Since pine wood chips and oak cuts have relatively greater shear strength even in the absorbing state than the other materials, they will be able to endure some power in the case of stirring with pig droppings.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.45 no.3
• /
• pp.217-224
• /
• 2019

Phthalates, endocrine disrupting chemicals, are similar in structure to sex hormones and mainly show reproductive toxicity and developmental toxicity. In this study, we analyzed 11 phthalates, including 3 kinds of phthalates prohibited in cosmetic use and 8 kinds of phthalates regulated in 'Common standards for children's products safety' and EU cosmetic regulation (EC No. 1223/2009). The phthalate analysis was optimized using GC-MS/MS. In analytical method validation, this method was satisfied in specificity, linearity, recovery rate, accuracy and MQL. Therefore, we used this method to analyze 82 products of Nail cosmetics & polish. Although six phthalates such as DBP, BBP, DEHP, DPP, DIBP and DIDP were detected at concentrations of $1.0{\sim}59.8{\mu}g/g$g, they were suitable to Korean cosmetic standards. DIBP and DBP were detected at concentration of $1.1{\sim}2.6{\mu}g/g$ in artificial nail, DBP and DEHP were $1.4{\sim}2.5{\mu}g/g$ in glue for nails, and DIBP, DBP, and DEHP were $2.5{\sim}33.3{\mu}g/g$ in nail stickers. Although substances such as DBP and DEHP in artificial nail, Glue for nails, and nail stickers were detected, they were suitable to 'Common safety standards for children's products. DIBP is not a regulated substance in Korea but showed the third highest detection rate following DBP (84.6%) and DEHP (63.4%). The concentration of phthalates detected in nail products is considered to be safe in current standards but continuous monitoring and research about non-regulated substances are also needed to be considered.

• Korean Journal of Heritage: History & Science
• /
• v.49 no.2
• /
• pp.56-69
• /
• 2016

Flame resistant treatment has been applied since 1973 for fire prevention in historical wooden buildings, but several problems, such as whitening and discoloration are constantly occurring in some Dancheong, in spite of evaluation criteria. It is supposed that these phenomena are caused by the stability issue of flame retardant, Dancheong production methods, the residue of chemicals, which were applied in the past, building location environments, etc., but no evaluation and cause inspection has been performed. Therefore, this study aims to verify the effect of flame retardant on Dancheong by producing Pseudo-samples and setting spatial and temporal environment conditions. Pseudo-samples of Dancheong were produced using three methods; the method specified in the Standard Specification of Properties; the method, which is generally used in the site and the traditional method. For different environment conditions of pseudo-samples, the areas were classified into a coastal area and an inland area and the places were classified into a sunny place and a wetland. After applying a flame retardant, annual variations were inspected for 12 months and change aspects were observed through scan and regular observation. In annual variation inspection, various variations like whitening, decolorization, dissolution and exfoliation were found and especially, whitening was most dominant. When the effect of flame retardant depending on the production methods was analyzed, whitening occurred in all the three production methods. It is supposed that this is because calcium(Ca) was contained in the coloring material of each production method and it reacted with phosphorous(P) of flame retardant. When the effect of flame retardant depending on the environment conditions was analyzed, whitening occurred more in the coastal area than in the inland area and it reduced in the building in a sunny place, which was constructed using the traditional method. It is supposed that this results from the humidity change and the difference of glue used in each production method. In conclusion, for using a flame retardant containing phosphorous(P), there is a need to check if calcium components including Oyster Shell White were used in Dancheong in advance and to conduct various preliminary studies on place conditions and Dancheong construction conditions.

• Journal of the Korean Society of International Agriculture
• /
• v.30 no.4
• /
• pp.328-338
• /
• 2018

Central Asia (Uzbekistan, Kazakhstan, Kyrgyzstan) is a hot and arid continental climate, with most areas (68%) consisting of barren vegetation, desert, and meadows. The main agricultural areas for crop production include irrigated farmland, non-irrigated farmland, grassland, prairie and mountain. We are experiencing climate change with recent climate variability increasing. Agriculture is one of major economic sectors and provides a means of livings for the rural population of Central Asia, especially the poor. In the past two decades, Central Asia has experienced a high population growth rate, with Kazakhstan at 16.8%, Uzbekistan at 34.5% and Kyrgyzstan at 28.4%. As a major industry, Kazakhstan has the largest share of exports of agricultural products followed by petroleum, mineral resources, steel, and chemicals. Uzbekistan is the fifth largest cotton exporter as well as the sixth largest cotton producer in the world. Kyrgyzstan exports ores, stones, cultured pearls, and minerals. These three countries are rich in mineral resources, agricultural products, and energy resources. However, not only do they have difficulties in economic development due to the weakness of logistics and industrial infrastructure, but they also have imperceptible cooperation and investment among countries due to insufficient research and development. Through this study, we will investigate national outlook, economic indicators, major agricultural products, import and export status, and agricultural technology cooperation status, and study how Korean agricultural industry advances into these countries through SWOT analysis. Through this, we hope to contribute to the basic data of Central Asian studies and cooperation and investment in agriculture in each country. In addition, in order to increase cooperative exchange and investment in these countries, we will prepare a Central Asia logistics hub for the rapidly changing interKorean railroad era.

• Journal of Bio-Environment Control
• /
• v.31 no.4
• /
• pp.376-383
• /
• 2022

The current study, which consisted of two independent studies (laboratory and greenhouse), was carried out to project the hypothesis fungi-spray scheduling for leaf mold and gray leaf spot in tomato, as well as to evaluate the effect of temperature and leaf wet duration on the effectiveness of different fungicides against these diseases. In the first experiment, tomato leaves were infected with 1 × 10⁴ conidia·mL^-1 and put in a dew chamber for 0 to 18 hours at 10 to 25℃ (Fulvia fulva) and 10 to 30℃ (Stemphylium lycopersici). In farm study, tomato plants were treated for 240 hours with diluted (1,000 times) 30% trimidazole, 50% polyoxin B, and 40% iminoctadine tris (Belkut) for protection of leaf mold, and 10% etridiazole + 55% thiophanate-methyl (Gajiran), and 15% tribasic copper sulfate (Sebinna) for protection of gray leaf spot. In laboratory test, leaf condensation on the leaves of tomato plants were emerged after 9 hrs. of incubation. In conclusion, the incidence degree of leaf mold and gray leaf spot disease on tomato plants shows that it is very closely related to formation of leaf condensation, therefore the incidence of leaf mold was greater at 20 and 15℃, while 25 and 20℃ enhanced the incidence of gray leaf spot. The incidence of leaf mold and gray leaf spot developed 20 days after inoculation, and the latency period was estimated to be 14-15 days. Trihumin fungicide had the maximum effectiveness up to 168 hours of fungicides at 12 hours of wet duration in leaf mold, whereas Gajiran fungicide had the highest control (93%) against gray leaf spot up to 144 hours. All the chemicals showed an around 30-50% decrease in effectiveness after 240 hours of treatment. The model predictions in present study could be help in timely, effective and ecofriendly management of leaf mold disease in tomato.

• Korean Journal of Remote Sensing
• /
• v.38 no.6_3
• /
• pp.1817-1826
• /
• 2022

After the hydrogen fluoride leak in Gumi in 2012, the government has been systemizing the disaster management system, such as responding to and managing chemical accidents. In particular, the Ministry of the Interior and Safety (MOIS) is in charge of evacuation of residents following chemical accidents based on the Framework Act on Management of Disaster and Safety. In this study, an application plan was presented to support and utilize the decision-making support for evacuation of residents after a chemical accident using the chemical accident investigation equipment of the National Disaster Management Research Institute (NDMI). In the equipment operation system for scientific information collection due to chemical accidents, the roles and purpose of use of long/short distance measurement equipment were presented according to regular and emergency situations. Using the data acquired through long/short distance measurement equipment, it can be used as basic data for resident evacuation decision-making by monitoring whether chemicals are detected in an emergency and managing data on detected substances by company in a regular situation. As a result of measuring chemical substances in order to verify on-site usability by equipment only for the regular operation system, it was confirmed that real-time detection of chemical substances is possible with long distance measuring equipment. In addition, it was confirmed that it was necessary to check the measurable distance and range of the equipment in the future. In the case of short distance measurement equipment, hydrocarbon-based substances were mainly detected, and it was confirmed that it was measured at a higher level in Ulsan-Mipo National Industrial Complex than in Onsan National Industrial Complex. It is expected that it can be used as basic data to support decision-making in the event of chemical accidents through continuous data construction in the future.

• Korean Journal of Ecology and Environment
• /
• v.55 no.3
• /
• pp.185-200
• /
• 2022

The risk of various hazardous substances in aquatic environment comprises not only the concentration of substances in the environmental medium but also their accumulation in fish through complex food web and the health risks to humans through the fish. In Korea, the monitoring of residual toxicant in aquatic ecosystems began in 2016 following the enforcement of the Acts on registration and evaluation for the management of chemicals used in daily life (consumer chemical products), and attention has been paid to potentially hazardous substances attributed to them. Recently, studies have been carried out to investigate the distribution of these hazardous substances in the ecosystem and calculate their emission factors. These include the accumulation and transport of substances, such as detergents, dyes, fragrances, cosmetics, and disinfectants, within trophic levels. This study summarizes the results of recently published research on the inflow and distribution of hazardous substances from consumer chemical products to the aquatic environment and presents the scientific implication. Based on studies on aquatic environment monitoring techniques, this study suggests research directions for monitoring the residual concentration and distribution of harmful chemical substances in aquatic ecosystems. In particular, this study introduces the directions for research on trophic position analysis using compound specific isotope analysis and trophic magnification factors, which are needed to fulfill the contemporary requirements of selecting target fish based on the survey of major fish that inhabit domestic waters and assessment of associated health risk. In addition, this study provides suggestions for future biota monitoring and chemical research in Korea.

• Clean Technology
• /
• v.29 no.1
• /
• pp.31-38
• /
• 2023

Due to water shortages caused by water pollution and climate change, total organic carbon (TOC) standards have been implemented for wastewater discharged from public sewage treatment facilities. Furthermore, there is a growing interest and body of research pertaining to the reuse of sewage treatment water as a secure alternative water resource. The membrane bio-reactor (MBR) method is commonly used for advanced wastewater treatment because it can remove organic and inorganic ions and it does not require or emit any chemicals. However, the MBR process uses a separation membrane (MF), which requires frequent film cleaning due to fouling caused by a high concentration of mixed liquor suspended solid (MLSS). In this study, process improvement and microbubble cleaning efficiency were evaluated to improve the differential pressure, water flow, and MF fouling, which are the biggest disadvantages of operating the MF. The existing MBR method was improved by installing a precipitation tank between the air tank and the MBR tank in which raw water was introduced. Microbubbles were injected into a separation membrane tank into which the supernatant water from the precipitation tank was introduced. The microbubble generator was operated with a 15 day on, 15 day off cycle for 5 months to collect discharged water samples (4L) and measure TOC. As the supernatant water from the precipitation tank flowed into the separation membrane tank, about 95% of the supernatant water MLSS was removed so the MF fouling from biological contamination was prevented. Due to the application of microbubbles to supernatant water from the precipitation tank, the differential pressure of the separation membrane tank decreased by 1.6 to 2.3 times and the water flow increased by 1.4 times. Applying microbubbles increased the TOC removal rate by more than 58%. This study showed that separately operating the air tank and the separation membrane tank can reduce fouling, and suggested that applying additional microbubbles could improve the differential pressure, water flow, and fouling to provide a more efficient advanced treatment method.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.31 no.1
• /
• pp.35-45
• /
• 2023

In this study, the sludge formation in the wastewater drain from the advanced packaging process mechanisms are revealed as well as the key factors, materials, and sludge prevention methods using surfactant. Compared with that of conventional packaging process, advanced packaging process employ similar process to the semiconductor fabrication process, and thus many processes may generate wastewater. In specific, a large amount of wastewater may generate during the carrier wafer bonding, photo, development, and carrier wafer debonding processes. In order to identify the key factors for the formation of sludge during the advanced packaging process, six types of chemicals including bonding glue, HMDS, photoresist (PR), PR developer, debonding cleaner, and water are utilized and mixing evaluation is assessed. As a result, it is confirmed that the black solid sludge is formed, which is originated by the sludge seed formation by hydrolysis/dehydration reaction of HMDS and sludge growth via hydrophobic-hydrophobic binding with sludge seed and PR. For the sludge prevention investigation, three surfactants of CTAB, PEG, and shampoo are mixed with the key materials of sludge, and it is confirmed that the sludge formations are successfully suppressed. The underlying mechanism behind the sludge formation is that the carbon tails of the surfactant bind to PR with hydrophobic-hydrophobic interaction and inhibit the reaction with HMDS-based slurry seeds to prevent the sludge formation. In this regard, it is expected that various problems like clogging in drains and pipes during the advanced packaging process may effectively solve by the injection of surfactants into the drains.

• Korea Trade Review
• /
• v.42 no.6
• /
• pp.111-129
• /
• 2017

According to the World Bank statistics, China's contribution to global economic growth during the year of 2013-2016 was estimated at 31.6 percent. This figure is even larger than 29.0 percent, the contribution by summing each contribution of the United States, EU and Japan. The Chinese commodity trade accounts for up to 11.5 percent of world trade volume. Thus, we can consider that the Chinese economy has a strong influence on the global economy. The primary purpose of this study is to analyze the contribution level of Chinese seaborne trade volume on world economy. First, this study conducted a time-lag analysis using Moran test, so we can find that China's level of contribution to global economic growth varies from time to time. The contribution of the first phase (1999-2007) was nearly three times higher than the contributions from the second phase (2008-2016), suggesting that the overall contraction of the global trade volume starting from the subprime mortgage crisis in 2008 has continued until recently and recovery has not even occurred. Second, using the econometrics model, this study conducted an regression analysis of the impact of Chinese imports and exports in chemicals, grain, steel, crude oil, and container on global economic growth. Fixed effects model with time series data has been applied to examine the effect of Chinese seaborne trade volume on global economic growth. According to the empirical analysis of this study, China's exports of steel products, exports of container, imports of containers, imports of crude oil and imports of grain have significant contributions to global economic growth. Estimates of China's exports of steel products, exports of container, imports of containers, imports of crude oil and imports of grain are 1.023, 1.020, 1.019, 1.007 and 1.006, respectively. For example, the estimated value 1.023 of China's exports of steel products means that the growth rate can be 1.023 times higher than the current world GDP growth rate if Chinese seaborne trade volume of exports of steel products increased by one unit (one million tons). This study concludes that the expansion of China's imports and exports should be realized first to increase the global GDP growth rate. The expansion of Chinese trade can lead to a simultaneous stimulus of production and consumption in China, which can even lead to global economic growth ultimately. Thus, depending on how much China's trade will be broaden in the future, the width of global economic growth can be determined.