• Korea-Australia Rheology Journal
• /
• 제14권2호
• /
• pp.63-70
• /
• 2002

Chemical mechanical planarization (CMP) is the polishing process enabled by both chemical and mechanical actions. CMP is used in the fabrication process of the integrated circuits to achieve adequate planarity necessary for stringent photolithography depth of focus requirements. And recently copper is preferred in the metallization process because of its low resistivity. We have studied the effects of chemical reaction on the polishing rate and surface planarity in copper CMP by means of numerical simulation solving Navier-Stokes equation and copper diffusion equation. We have performed pore-scale simulation and integrated the results over all the pores underneath the wafer surface to calculate the macroscopic material removal rate. The mechanical abrasion effect was not included in our study and we concentrated our focus on the transport phenomena occurring in a single pore. We have observed the effects of several parameters such as concentration of chemical additives, relative velocity of the wafer, slurry film thickness or ash)tract ratio of the pore on the copper removal rate and the surface planarity. We observed that when the chemical reaction was rate-limiting step, the results of simulation matched well with the experimental data.

• 마이크로전자및패키징학회지
• /
• 제18권3호
• /
• pp.25-32
• /
• 2011

초고휘도 비극성 a-GaN LED를 위한 양질의 R-면 사파이어 기판을 제조하기 위해 절단, 연마공정에 대해서 연구하였다. 사파이어는 이방성이 큰 물질로서 R-면과 c-면의 기계적인 특성의 차이에 의해 기판 제조공정 조건이 영향을 받으며, c-면에 비해서 R-면은 이방성 크며 각 결정학적인 면에서의 이방성은 연마공정에는 큰 영향을 미치지 않으나 절단공정에 큰 영향을 미치는 것으로 나타났다. R-면 잉곳의 절단방향이 a-flat에 대해 $45^{\circ}$인 경우에 절단이 가장 효과적으로 이루어졌으며 양호한 절단품질을 얻을 수 있었다. 기계적인 연마가 이루어지는 래핑과 DMP(Diamond mechanical polishing) 공정에서는 c-면 기판과 연마율이 큰 차이가 나타나지 않았으나, 화학반응이 수반되는 CMP(Chemical mechanical polishing) 공정에서는 c-면 기판의 연마율이 R-면 기판의 약 2배 이상 큰 값을 가졌으며, 이는 c-면의 수화반응층 형성에 의한 영향으로 보여진다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 학술대회 논문집 일렉트렛트 및 응용기술연구회
• /
• pp.105-108
• /
• 2003

CMP(chemical mechanical polishing) process has been attracted as an essential technology of multi-level interconnection. However, the COO(cost of ownership) is very high, because of high consumable cost. Especially, among the consumables, slurry dominates more than 40 %. So, we focused how to reduce the consumption of raw slurry. In this paper, We have studied the CMP (chemical mechanical polishing) characteristics of slurry by adding of raw alumina abrasive and annealed alumina abrasive. As a experimental results, we obtained the comparable slurry characteristics compared with original silica slurry in the view point of high removal rate and low non-uniformity. Therefore, we can reduce the cost of consumables(COC) of CMP process for ULSI applications.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.719-722
• /
• 2004

In this work, we applied the chemical mechanical polishing (CMP) process to the planarization of ferroelectric film. We compared the structural characteristics of BST $(Ba_{0.6}Sr_{0.4}TiO_3)$ films before and after the CMP process. Their dependence on slurry composition was also investigated. Finally, we suggest the self-developed titania $(TiO_2)$ mixed abrasive slurry (MAS) for FRAM applications. Our experimental results on the ferroelectric film are encouraging for the next generation of FRAM applications.

• 한국전기전자재료학회논문지
• /
• 제16권6호
• /
• pp.465-470
• /
• 2003

The chemical mechanical polishing (CMP) process has been widely used for the global planarization of multi-layer structures in semiconductor manufacturing. The CMP process can be optimized by several parameters such as equipment, consumables (pad, backing film and slurry), process variables and post-CMP cleaning. However, the COO(cost of ownership) is very high, because of high consumable cost. Especially, among the consumables, the slurry dominates more than 40 %. In this paper, we have studied the CMP characteristics of diluted silica slurry by adding of raw alumina abrasives and annealed alumina abrasives. As an experimental result, we obtained the comparable slurry characteristics compared with original silica slurry in the view-point of high removal rate and low non-uniformity. Therefore, we can reduce the cost of consumables(COC) of CMP process for ULSI applications.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.172-176
• /
• 1996

The rapid structural change of ULSI chip includes minimum features, multilevel interconnection and large diameter wafers. Demands for the advanced chip structure necessitates the development of enhanced deposition, etching and planarization techniques. Planarization refers to a process that make rugged surfaces flat and uniform. One of the emerging technologies for planarization is chemical mechanical polishing(CMP). Chemical and mechanical removal actions occur during CMP, and both appear to be closely interrelated. The purpose of this study is the optimal application of the slurry to the various types of device materials during CMP. We investigates the effect of slurry on CMP characteristics for thermal oxide and sputtered Al blanket wafers. Results from the polishing rate and the uniformity of residual film include mechanical and chemical reactions between several set of slurry and work material.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권10호
• /
• pp.441-446
• /
• 2003

The chemical mechanical polishing (CMP) process is now widely employed in the ultra large scale integrated (ULSI) semiconductor fabrication. Especially, shallow trench isolation (STI) has become a key isolation scheme for sub-0.13/0.10${\mu}{\textrm}{m}$ CMOS technology. The most important issues of STI-CMP is to decrease the various defects such as nitride residue, dishing, and tom oxide. To solve these problems, in this paper, we studied the planarization characteristics using slurry additive with the high selectivity between $SiO_2$ and $Si_3$$N_4$ films for the purpose of process simplification and in-situ end point detection. As our experimental results, it was possible to achieve a global planarization and STI-CMP process could be dramatically simplified. Also, we estimated the reliability through the repeated tests with the optimized process conditions in order to identify the reproducibility of STI-CMP process.

• Transactions on Electrical and Electronic Materials
• /
• 제3권4호
• /
• pp.5-9
• /
• 2002

Chemical mechanical polishing (CMP) has become the preferred planarization method for multilevel interconnect technology due to its ability to achieve a high degree of feature level planarity. Especially, to achieve the higher density and greater performance, shallow trench isolation (STI)-CMP process has been attracted attention for multilevel interconnection as an essential isolation technology. Also, it was possible to apply the direct STI-CMP process without reverse moat etch step using high selectivity slurry (HSS). In this work, we determined the process margin with optimized process conditions to apply HSS STI-CMP process. Then, we evaluated the reliability and reproducibility of STI-CMP process through the optimal process conditions. The wafer-to-wafer thickness variation and day-by-day reproducibility of STI-CMP process after repeatable tests were investigated. Our experimental results show, quite acceptable and reproducible CMP results with a wafer-to-wafer thickness variation within 400$\AA$.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권9호
• /
• pp.466-470
• /
• 2001

We have developed a sub-micron gap fabrication technology using chemical-mechanical polishing (CMP) without /the sub-micron lithography equipments (0.18∼0.25 7m). And it has been applied to a lateral field emission device (FED), in which narrow gap distance is very important for reducing turn-on voltage. As a result, the turn-on voltage (at which the current level is 1 nA) of the fabricated device with the gap distance of 256 nm is as low as 4.0 V, which is the lowest turn-on voltage among lateral FEDs ever reported.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권12호
• /
• pp.549-554
• /
• 2006

In this paper we first applied the chemical mechanical polishing (CMP) process to the planarization of ferroelectric film in order to obtain a good planarity between electrode and ferroelectric film. $Pb_{1.1}(Zr_{0.52}Ti_{0.48})O_3$ (shortly PZT) ferroelectric film was fabricated by the sol-gel method. And then, we compared the structural characteristics before and after CMP process of PZT films. Removal rate, WIWNU% and surface roughness have been found to depend on slurry abrasive types and their hardness, especially, surface roughness and planarity were strongly depends on its pH value. A maximum in the removal rate is observed in the silica slurry, in contrast with the minimum removal rate occurs at ceria slurry. We found that the surface roughness of PZT films can be significantly reduced using the CMP technique.