• Composites Research
• /
• 제18권5호
• /
• pp.27-33
• /
• 2005

본 연구에서는 펄스-CVI (Chemical Vapor Infiltration)에 의해 탄화규소/탄소 복합재료를 제조하는 공정에 대한 수치모사가 행해졌다. 각 펄스가 가스 주입시간, 반응시간, 배출시간으로 구성될 때, 반응시간과 배출시간의 영향이 관찰되었다. 또한 반응가스 농도와 압력의 영향이 연구되었다. 탄소프리폼에의 탄화규소의 균일한 침착과 반응시간 단축을 위한 펄스-CVI공정의 이점이 확인되었다.

• 한국세라믹학회지
• /
• 제30권12호
• /
• pp.993-998
• /
• 1993

Nicalon-fiber-reinforced SiC composites were fabricated via polymer solution infiltration/chemical vapor infiltration (PSI/CVI) and CVI. Specifically, data were taken and compared for flexural strength, fracture toughness, and processing time. The two process resulted in comparable mechanical properties, and PSI/CVI process resulted in significantly reduced infiltration time.

• Carbon letters
• /
• 제4권4호
• /
• pp.163-167
• /
• 2003

The "Film boiling" Chemical Vapor Infiltration (CVI) process is a rapid densification one developed in particular for the elaboration of carbon/carbon composite materials. In order to optimize this new thermal gradient process, we have carried out several studies, on one hand, about the nature of the complex chemical reactions in a confined medium, and on the other hand, relative to the role of heat and mass transfers inside the preform. We show in this study that the introduction of a permeable sheath around the preform leads to hybrid liquid/gas CVI process which presents the advantages of very high densification rates associated with a moderate input energy.

• 한국세라믹학회지
• /
• 제33권8호
• /
• pp.935-941
• /
• 1996

Two-dimensional carbon/carbon preforms made of PAN-based carbon yarn and phenolic resin were densified with pyrolysis of propane by pulse chemical vapor infiltration where repeated the cycle of gas introduction residence and evacuation. Maximim density increment was 14% when infiltration temperature and time were 100$0^{\circ}C$ and 21.25 hrs respectively. The distribution of deposits of pyrocarbon by this process has been occurred uniformly in the bottom middle and top of carbon/carbon composite preform Pulse CVI with residence is most effective in increasing density and shortening infiltration time among isothermal CVI and pulse CVI with and without residence.

• 한국세라믹학회지
• /
• 제55권4호
• /
• pp.392-399
• /
• 2018

$C_f/SiC$ composites were prepared via a process combining chemical vapor infiltration (CVI) and precursor infiltration pyrolysis (PIP), wherein silicon carbide matrices were infiltrated into 2.5D carbon preforms. The obtained composites exhibited porosities of 20 vol % and achieved strengths of 244 MPa in air at room temperature and 423 MPa at $1300^{\circ}C$ under an Ar atmosphere. Carbon fiber pull-out was rarely observed in the fractured surfaces, although intermediate layers of pyrolytic carbon of 150 nm thickness were deposited between the fiber and matrix. Fatigue fracture was observed after 1380 cycles under 45 MPa stress at $1000^{\circ}C$. The fractured samples were analyzed by transmission electron microscopy to observe the distributed phases.

• Carbon letters
• /
• 제25권
• /
• pp.25-32
• /
• 2018

In this study, a thermal-gradient chemical vapor infiltration (TG-CVI) process was numerically studied in order to enhance the deposition uniformity within the preform. The computational fluid dynamics technique was used to solve the governing equations for heat transfer and gas flow during the TG-CVI process for two- and three-dimensional (2-D and 3-D) models. The temperature profiles in the 2-D and 3-D models showed good agreement with each other and with the experimental results. The densification process was investigated in a 2-D axisymmetric model. Computation results showed the distribution of the SiC deposition rate within the preform. The results also showed that using two-zone heater gave better deposition uniformity.

• 한국세라믹학회지
• /
• 제51권5호
• /
• pp.430-434
• /
• 2014

$SiC_f$/SiC composites were prepared using the hybrid process of chemical vapor infiltration (CVI) and polymer impregnation and pyrolysis (PIP). Before the application of PIP, partially matrix-filled preform composites with different densities were fabricated by control of chemical vapor infiltration time and temperature. The changes of the final density of the $SiC_f$/SiC composites had a tendency similar to that of preform composites partially filled by CVI. Composites with lower density after the CVI process had a larger increment of density during the PIP process. Three types of microstructures were observed on the fractured surface of the composite: 1) well pulled-out fibers and lower density, 2) slightly pulled-out fibers and higher density, and 3) only bulk SiC. The different fractions and distributions of the microstructures could have an effect on the mechanical properties of the composites. In this study, $SiC_f$/SiC composites prepared using a hybrid process of CVI and PIP had density values in the range of $1.05{\sim}1.44g/cm^3$, tensile strength values in the range of 76.4 ~ 130.7 MPa, and fracture toughness values in the range of $11.2{\sim}13.5MPa{\cdot}m^{1/2}$.

• 한국세라믹학회지
• /
• 제51권5호
• /
• pp.453-458
• /
• 2014

SiC and its composites have been considered for use as nuclear fuel cladding materials of pressurized light water reactors. In this study, a $SiC_f$/SiC composite as a constituent layer of SiC triplex fuel cladding was fabricated using a chemical vapor infiltration (CVI) process in which tubular SiC fiber preforms were prepared using a filament winding method. To enhance the matrix density of the composite layer, winding patterns, deposition temperature, and gas input ratio were controlled. Fiber arrangement and porosity were the main parameters influencing densification behaviors. Final density of the composites decreased as the SiC fiber volume fraction increased. The CVI process was optimized to densify the tubular preforms with high fiber volume fraction at a high $H_2$/MTS ratio of 20 at $1000^{\circ}C$; in this process, surface canning of the composites was effectively retarded.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.484-487
• /
• 2009

$SiC_f$/SiC composites with whiskers and pyrolytic carbon (PyC) coated whiskers in the matrix were fabricated for enhancement of the fracture behaviors by the whisker growing assisted chemical vapor infiltration (WA-CVI) process, respectively. $SiC_f$/SiC composites were also prepared by the conventional CVI process as reference material. The mechanical properties and fracture behaviors were analyzed by comparison of the two types of composites prepared by WA-CVI and conventional CVI. The densities of $SiC_f$/SiC composites were in the range of $2.6{\sim}2.65g/cm^3$. The flexural strengths of composite with whiskers and with those coated by PyC were 650 MPa and 600 MPa, respectively. The tensile strength of composites with whiskers was ${\sim}285$ MPa.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 추계학술발표대회 논문집
• /
• pp.141-143
• /
• 2001

Ceramic fiber-reinforced composites have good mechanical properties in hardness and durability. In this study, we studied the formation of SiC/C composites from methyltrichlorosilane and hydrogen by the Pulse-chemical vapor infiltration(PCVI) to deposit silicon carbide around the changes of the amount of deposit. SiC/C composites formed at $950^{\circ}C$, 20torr, Pulse-times (5s/60s). SEM of the cross sectional area of semple showed deposited silicon carbide around fibers.