• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.391-394
• /
• 2009

Asymmetrical and unbalanced features such as rotor blade of helicopter, actuator of hard-disk in personal computer are usually manufactured with composite materials. In this case, mass distributions and center of gravity of the parts are important because of their static balancing. Therefore in the manufacturing processes, it is needed to check out the exact data of weight and gravity center. In this study, it has been studied experimentally the balancing of laminated rotor blade by using multiple-point weighing method and lab-view system.

• Structural Monitoring and Maintenance
• /
• 제5권3호
• /
• pp.345-361
• /
• 2018

The set of processes performed to determine the dynamic characteristics of the constructed structures is named experimental modal analysis. Using experimental modal analysis and interpreting its results, structural failure can be assessed and then it would be possible to plan for their repair and maintenance. The purpose of the experimental modal analysis is to determine the resonance frequencies, mode shapes and Mode damping for the structure. Diverse methods for determining the shape of the mode by various researchers have been presented. There are pros and cons for each of these methods. This paper presents a method for determining the mode shape of the structures using the response spectrum in the experimental modal analysis. In the first part, the principles of the proposed method are described. Then, to check the accuracy of the results obtained from the proposed method, single and multiple degrees of freedom models were numerically and experimentally investigated.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.29-46
• /
• 1999

The performance based design obligates quantitative assessment of required performances by means of transparent and objective science. In this design scheme, simulation of both macro and micro-scale structural behaviors is thought to be a powerful tool. This paper proposes a way how to unify the structural safety and serviceability check method and durability assessment of RC structures. Though component chemical-physical processes are crudely assumed, system dynamics of micro-scale pore structure formation and macro-scale defects and deformation of structures was shown as possible and promising approach in future. The authors understand that the unification of structural and durability design has just started. For further progress and development, predictive tool of structural behaviors from birth to death of concrete under any specified environment and load serves as an essential technicality.

• 한국생산제조학회지
• /
• 제4권3호
• /
• pp.12-24
• /
• 1995

Various surface grinding experiments using resin bonded diamond abrasive wheels are carried out for tungsten carbide materials in order to minimize the damage on the ground surface and to purse the precise dimension compared to conventional grinding machine. When grinding quality is constant, theoretical grinding effect is changed according to the speed of workpiece. Accordingly, grinding forces, which are Fn, Ft, were analyzed for the machining processes of tungsten-carbide material to obtain optimum grinding conditions. Brief investigation is carried out to decrease the dressing efficiency of resinoid bonded diamond grinding wheel to grind tungsten-carbide. Truing is also carried out to provide a desired shape on a wheel or to correct a dulled profile. High quality in dimensional accuracy and surface are often required as a structural components, therefore 3-points bending test is carried out to check machining damage on the ground surface layer, which in one of sintered brittle material. From this experimental study, some useful machining data and information to determine proper machining condition for grinding of tungsten-carbide materials are obtained.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1849-1852
• /
• 2005

An automatic cap-washing machine is developed for rinse and dry of synthetic resin cap which is used in spring water bottle. This machine should be achieved all processes washing and drying, array, transfer automatically. A cap is washed by an ozonized water and pure water first. Next, a cap is dried by a hot wind drying equipment. In this paper, structural and modal analysis for the cap-washing machine is carried out to check the design criterion of the machine. The analysis is carried out by FEM simulation using the commercial software, CATIA V5. And a fictitious mass properties was used for the analysis of the machine. Finally, the machine performance is shown to be satisfactory.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.216-220
• /
• 2003

Most important for meaningful forging simulation is the determination of correct process parameters. In addition a check and a compensation of the data base after the comparison between experiments and the computation of the developed process is necessary. The existence of a systematic process parameter data bank for special kinds of forming process in combination with forging specific simulation lifts the value of the products. Finite volume method is applied to simulate the hot forging process to investigate the defects for the automobile product. Three typical forging processes have been investigated; Extrusion by hydrolic press, Upsetting by crank press and Inclined upsetting by hammer press. Simulated result has compared with the experiment and provided a direction to improve the process.

• 산업공학
• /
• 제15권4호
• /
• pp.356-363
• /
• 2002

Virtual Manufacturing is a technology to facilitate effective product development and agile production by computer models representing the physical and logical schema and the behavior of real manufacturing systems including manufacturing resources, environments and products. For the successful application of this technology, a virtual factory as a well-designed and integrated environment is essential. In this research, we constructed a sophisticated virtual factory model of an automotive company's paint shop, and performed precise simulations of unit cells, lines and whole plant operations for collision check and off-line programming. It is expected that this virtual paint shop is useful for achieving time and cost savings in many manufacturing preparation and planning activities of new car development processes.

• 산업공학
• /
• 제17권4호
• /
• pp.414-425
• /
• 2004

This study presents the decision of priority for optimal design guide to improve disassembly process. Disassembly process is divided into recognition, transfer and disassembly of assembly point and recognition, transfer and remove of grasp point. Significant influential factors are derived from analyzing the above process. And those factors are used for making the check list to evaluate the properties of parts in each process. Furthermore, the weight with considering disassembly process is also used to determine weight of each process. On the base of the above sequence, qualitative score of disassemblability of each process that is enabled to compare different disassembly processes can be acquired. Ultimately the score helps to decide the priority of design guide for disassembly process.

• 대한방사선치료학회지
• /
• 제11권1호
• /
• pp.28-32
• /
• 1999

Verifying the treatment value(Monitor Unit) unnecessarily involves too many simple and repetitive calculation processes, that is, individual computation process using the data(PDD value, Scp Factor, SSD Factor, Tray Factor) on the data book. We intend to minimize the time required to check the Monitor Unit through computerized calculation. Using $^{\ast}(multiplication)$, /(division), +(sum), if function, among others, which are present in the Excell program, MS office program, the Monitor Unit was obtainable through A/P value, Scp Factor and PDD value, Wedge Factor. From the verification of the computations of Monitor Unit for 60 patients previously treated, we were able to obtain an error rate of ${\pm}0.028MU$. Computerized calculation of the Monitor Unit could save the burden of Technologist.

• 인터넷정보학회논문지
• /
• 제3권4호
• /
• pp.19-26
• /
• 2002

본 논문에서는 워크플로우 관리 시스템의 빌드타임 기능에 속하는 모델링 시스템을 다중 에이전트 기반으로 구현하였다. 본 논문에서 제안된 다중 에이전트 기반 워크플로우 모델링 시스템은 클라이언트의 경량을 위하여 자바를 이용하였으며, 프로세스 정의에 필요한 세션, 조직, 관련데이터, 응용프로그램 속성들을 별도의 에이전트로 구성하였다 또한, 프로세스 정의를 위한 모델은 ICN(Information Control Net)을 이용하여 작성된 모델의 문법(syntax)를 검증하였으며, 타 워크플로우 엔진과의 연동을 위하여 WfMC에서 정의된 인터페이스 형태인 WPDL로 import/export할 수 있는 기능을 제공한다.