• Tribology and Lubricants
• /
• v.25 no.4
• /
• pp.261-264
• /
• 2009

Environmental factors affect parts of the automobile. When dust particles are embedded, specially, friction and wear of the rubber-seal in automobile chassis system are increased. Increase in friction and wear leads to weakness of component and reduction of mechanical life. In this study, the wear characteristics of rubber-seal for inflow of dust particles are investigated. Silica($SiO_2$) and alumina($Al_2O_3$) particles are used as a dust particle because these particles are main elements of dust particles. The sliding wear tester are used for investigate the wear characteristics of rubber-seal. If the single dust particle($SiO_2$) is embedded in the rubber-seal component, the influence of dust particle size is more than that of inflow rate on the wear characteristics of rubber-seal. If the mixed dust particles are embedded in the rubber-seal component, the wear rate is increased as the rate of alumina that has a bigger hardness is increased. If the mixed dust particles that have different hardness are embedded in the rubber-seal component, the influence of particle size is more than that of particle hardness.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.4
• /
• pp.454-462
• /
• 2016

This study was conducted in order to estimate the exhaust emissions analysis method of the real driving emission(RDE). The Association for Emissions Control by Catalyst(AECC) has developed a test procedure by using a random cycle method based on the chassis dynamometer. In order to confirm this approach in Korea, Euro 5(DPF), Euro 6(DPF + LNT), and Euro 6(DPF + SCR) were performed on three different vehicles to determine the exhaust gas characteristics of the random cycle, real-road driving test(PEMS), and emission certification driving mode(NEDC). Six different random cycle driving modes were generated by the vehicle specifications(e.g. curb weight, engine power, gear ratio, and maximum acceleration). The NOx emissions were increased in the NEDC, random cycle, and PEMS order in this study regardless of the test vehicles. The random cycle method has the advantage because it utilizes a chassis dynamometer in the laboratories for a repeatable data collection, and it allows any eminent emission improvement checked prior to a real-road driving test with PEMS.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.14 no.1
• /
• pp.94-102
• /
• 2015

The high-pass(brand name of Electronic Toll Collection System) utilization trend on the highway continues to grow as 59.4% (by the end of 2013). In this study, we applied the carbon balance method using a fuel chassis dynamometer with the four passenger car classes in order to measure the fuel consumption of the car using the expressway tollgate. We experimented 18 driving mode at general tollgate and high-pass tollgate. As a result, in case of entry/exit toll there were 21.0~56.4ml/veh fuel consumption savings, in case of open toll fuel consumption savings was analyzed as 10.5~28.1ml/veh. In addition, the annual fuel cost savings by virtue of high-pass was 28.2~57.3 billion won at 70% utilization rate, 32.2~65.5 billion won at 80%, 36.2~73.7 billion won at 90% and 40.3~81.9 billion won at 100%.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.284-285
• /
• 2008

For development of low fuel consumption vehicle, design of engine can he changed and it brings collateral effect. Abnormal vibration is one of bad effect of high efficiency engine and it can be got over by active engine mount system. For development of active engine mount system, an adequate experimental equipment is required which contain characteristic of real engine movement. To make adequate experimental equipment, regulated force vibrating system including characteristics of vehicle chassis is required.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.72-80
• /
• 2006

Electric Power Steering (EPS) mechanism has become widely equipped in passenger vehicle due to the increasing environmental concerns and higher fuel efficiency. This paper describes the development of concurrent simulation technique and simulation integration technique of EPS control system with a dynamic vehicle system. A full vehicle model interacting with EPS control algorithm was concurrently simulated on a single bump road condition. The dynamic responses of vehicle chassis and steering system resulting from road surface impact were evaluated and compared with proving ground experimental data. The comparisons show reasonable agreement on tie-rod load, rack displacement, steering wheel torque and tire center acceleration. This concurrent simulation capability was employed fur EPS performance evaluation and calibration as well as for vehicle handling performance integration and synthesis.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.106-114
• /
• 1999

Today, one of the most important objective in automobile development is to reduce the weight of automobile . The eventual depletion of petroleum and environmental regulations brought considerable emphasis to this area on increasing fuel efficiency. Conventional intake air-fuel system is very heavy because it is composed of numerous parts. The bulky size caused increase in the amount of metal being used to build automobile chassis and this became a serious weight problem. The size also caused difficulties in optimization of fuel supply system which in turn decreased engine efficiency. Currently , there are efforts to integrate several intake system modules into one. The purpose of this paper is to evaluate the directions of such development.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11b
• /
• pp.785-787
• /
• 2010

It is well known that most power steering systems obtain the power by a hydraulic mechanism. Therefore, it consumes more energy because the oil power should be sustained all the times. Recently, to solve this problem the Electric Power System(EPS) or Motor Driven Power System(MDPS) has widely equipped in passenger vehicles. In this research the concurrent simulation technique for an EPS system with MATLAB/SIMULINK and a full vehicle model has been developed. The dynamic responses of vehicle chassis and steering system are evaluated. Then, a full vehicle model interacted with EPS control is concurrently simulated with an impulsive steering wheel torque input to analyze the stability of 'free control' or hands free motion for SUV. This integrated method allows engineers to reduce the prototype testing cost and to shorten the developing period.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.1
• /
• pp.86-95
• /
• 1996

This study was on the pollution emissions of the Ultrasonic fuel feeding system in gasoline injection vehicle. This work measured th SMD of the fuel, and compared the characteristics through chassis dynamometer and highway road test by the conventional vehicle. And this work measured vacuum degree, turbulence intensity and the rate of fuel consumption according to intake air velocity with swirler. The results are as followed; The effects of the vehicle installed the ultrasonic fuel feeding system are better than those of the conventional vehicle.

• ETRI Journal
• /
• v.32 no.5
• /
• pp.827-830
• /
• 2010

For an adaptive cruise control (ACC) stop-and-go system in automotive applications, three radar sensors are needed because two 24 GHz short range radars are used for object detection in an adjacent lane, and one 77 GHz long-range radar is used for object detection in the center lane. In this letter, we propose a single sensor-based 24 GHz radar with a detection capability of up to 150 m and ${\pm}30^{\circ}$ for an ACC stop-and-go system. The developed radar is highly integrated with a high gain patch antenna, four channel receivers with GaAs RF ICs, and back-end processing board with subspace based digital beam forming algorithm.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.130-136
• /
• 2001

This paper presents an of a brake pressure restriction valve to a motorcycle anti-lock brake system(ABS). In the conventional anti-lock brake system of automobiles, slip ratio as a control variable is actively controlled, which requires wheel speed sensors, ECU, and a pressure modulator. In the ABS valve that has been developed for use in motorcycles, however, the brake pressure that is close to the wheel locking pressure is preset by simple exercises and then the valve just allows to pass the wheel locking pressure and cutoff the remaining pressure. Simulation studies with a single wheel braking dynamics and lumped chassis model show that the pressure restriction valve has basic ABS functions as well as some robustness properties for the uncertain load and road conditions as well as various initial braking speeds. Field tests also show that the pressure restriction valve avoids the wheel locking effectively.