• The KIPS Transactions:PartC
• /
• v.17C no.1
• /
• pp.1-14
• /
• 2010

IEEE 802.15.4[1] has been standardized for the physical layer and MAC layer of LR-PANs(Low Rate-Wireless Personal Area Networks) as a technology for operations with low power on sensor networks. The standardization is applied to the variety of applications in the shortrange wireless communication with limited output and performance, for example wireless sensor or virtual wire, but it includes vulnerabilities for various attacks because of the lack of security researches. In this paper, we analyze the vulnerabilities against the denial of sleep attacks on the MAC layer of IEEE 802.15.4, and propose a detection mechanism against it. In results, we analyzed the possibilities of denial of sleep attacks by the modification of superframe, the modification of CW(Contention Window), the process of channel scan or PAN association, and so on. Moreover, we comprehended that some of these attacks can mount even though the standardized security services such as encryption or authentication are performed. In addition to, we model for denial of sleep attacks by Beacon/Association Request messages, and propose a detection mechanism against them. This detection mechanism utilizes the management table consisting of the interval and node ID of request messages, and signal strength. In simulation results, we can show the effect of attacks, the detection possibility and performance superiorities of proposed mechanism.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.3
• /
• pp.230-236
• /
• 2020

A trash screen is installed in front of the inflow channel of a drainage pumping station, sewage treatment plant, and a power plant to block floating contaminants. The bottleneck phenomenon, which decreases the water inflow, causes damage to the damper as a result of clogging in between the screen if string type obstacles are not removed. In this paper, the apron was removed, and the screen was expanded, to prevent breakage of the bottleneck phenomenon and string type obstacles. This was designed using an extended rake by adding an inner rake in between the screen interspace to remove the bottleneck phenomenon and string type obstacles. To design the inner rake that satisfies the allowable stresses of the existing damper rake, the experiment points were determined according to the experimental design method using the inner rake vertical length and the thickness of the reinforced section as parameters. The use of the ANSYS static structural module and statistical analysis tool R software gives the optimized shape according to the response surface method. The relative error between the response surface analysis results and the simulation results was 1.63% of the determined optimal design-point rake length of 210.2 mm and the reinforcement section thickness of 2 mm. Through empirical experiments, a test rake was constructed to the actual size, and approximately 97% of the bottleneck phenomenon and string type obstacles could be removed.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.07a
• /
• pp.25-37
• /
• 2002

The most important industrial application of gamma radiation in characterizing green compacts is the determination of the density. Examples are given where this method is applied in manufacturing technical components in powder metallurgy. The requirements imposed by modern quality management systems and operation by the workforce in industrial production are described. The accuracy of measurement achieved with this method is demonstrated and a comparison is given with other test methods to measure the density. The advantages and limitations of gamma ray densitometry are outlined. The gamma ray densitometer measures the attenuation of gamma radiation penetrating the test parts (Fig. 1). As the capability of compacts to absorb this type of radiation depends on their density, the attenuation of gamma radiation can serve as a measure of the density. The volume of the part being tested is defined by the size of the aperture screeniing out the radiation. It is a channel with the cross section of the aperture whose length is the height of the test part. The intensity of the radiation identified by the detector is the quantity used to determine the material density. Gamma ray densitometry can equally be performed on green compacts as well as on sintered components. Neither special preparation of test parts nor skilled personnel is required to perform the measurement; neither liquids nor other harmful substances are involved. When parts are exhibiting local density variations, which is normally the case in powder compaction, sectional densities can be determined in different parts of the sample without cutting it into pieces. The test is non-destructive, i.e. the parts can still be used after the measurement and do not have to be scrapped. The measurement is controlled by a special PC based software. All results are available for further processing by in-house quality documentation and supervision of measurements. Tool setting for multi-level components can be much improved by using this test method. When a densitometer is installed on the press shop floor, it can be operated by the tool setter himself. Then he can return to the press and immediately implement the corrections. Transfer of sample parts to the lab for density testing can be eliminated and results for the correction of tool settings are more readily available. This helps to reduce the time required for tool setting and clearly improves the productivity of powder presses. The range of materials where this method can be successfully applied covers almost the entire periodic system of the elements. It reaches from the light elements such as graphite via light metals (AI, Mg, Li, Ti) and their alloys, ceramics ($AI_20_3$, SiC, Si_3N_4, $Zr0_2$, ...), magnetic materials (hard and soft ferrites, AlNiCo, Nd-Fe-B, ...), metals including iron and alloy steels, Cu, Ni and Co based alloys to refractory and heavy metals (W, Mo, ...) as well as hardmetals. The gamma radiation required for the measurement is generated by radioactive sources which are produced by nuclear technology. These nuclear materials are safely encapsulated in stainless steel capsules so that no radioactive material can escape from the protective shielding container. The gamma ray densitometer is subject to the strict regulations for the use of radioactive materials. The radiation shield is so effective that there is no elevation of the natural radiation level outside the instrument. Personal dosimetry by the operating personnel is not required. Even in case of malfunction, loss of power and incorrect operation, the escape of gamma radiation from the instrument is positively prevented.

• Korean Journal of Digital Imaging in Medicine
• /
• v.16 no.1
• /
• pp.43-47
• /
• 2014

Sens of insecutity of the public and professionals about harmful effects of radiation is increasing in an accident at the Chernobyl and Fkushima nuclear power plant.Anxiety was amplified to lack of information about radiation majority of people. To target the middle and high school in the region of Daegu and Gyeongsangbuk-do, to investigate the radiation recognition of the next generation, it is intended to present a model of education for the safe use of radiation. The High School of the six metropolitan cities, city, town through the questionnaire and needs to be educational experience of radiation and use knowledge level of radiation, experience in daily life, understanding of man-made radiation and natural radiation, information channel on radiation, the radiation Distribute the total 800 parts of, to recover the 629 unit, was analyzed for 155 females 474 males. Many people 75.36% of the people, to 24.64% female subjects of this investigation, was constant, respectively from 13 to 18 years age. It is a large number and 30.37% of the respondents as "normal" level of knowledge of radiation, for the type of radiation, most knew. You have answer for risk experience of the medical radiation was higher, touching a lot of information via the broadcast medium in general, and the accuracy is low. I thought we wanted to be educated three or more twice a year, as an educator,about 71.37% and radiation-related understanding of knowledge and background in accordance with the diversification of information channels, the regional differences between urban and rural areas. But I considered the difference age (grade) for each is displayed, intended for junior high school students, the target surface and use the occurrence of radiation, high school students, the need for education about risk and application of radiation through this study.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10C
• /
• pp.1017-1026
• /
• 2005

In burst OFDM system, the frame synchronization should be performed first for the acquisition of received frame and the estimation of the correct FFT-window position. The conventional frame synchronization algorithms using design features of the preamble symbol, the repetition pattern of the OFDM symbol by pilot sub-carrier allocation rule and Cyclic Prefix(CP), has difficulty in the detection of precise frame timing because its correlation characteristics would increase and decrease gradually. Also, the algorithm based on the correlation between the reference signal and the received signal has performance degradation due to frequency offset. Therefore, we adopt a differential correlation method that is robust to frequency offset and has the clear peak value at the correct frame timing for frame synchronization. However, performance improvement is essential for differential correlation methods, since it usually shows multiple peak values due to the repetition pattern. In this paper, we propose an enhanced frame synchronization algorithm based on the differential correlation method that shows a clear single peak value by using differential correlation between samples of identical repeating pattern. We also introduce a normalization scheme which normalizes the result of differential correlation with signal power to reduce the frame timing error in the high speed mobile channel environments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.4
• /
• pp.819-830
• /
• 2017

An FM radio based PCL system is a passive radar technique for detecting the multiple moving targets from FM radio signals and tracking the trajectories of the targets by calculating the cross-correlation function of direct-path signal and target echo signals. However, the interference signals are received from a surveillance channel, which is designed to receive the target echo signals. Because of this problem, the target echo signals are masked by the strong interference signals and this makes it difficult to detect the true targets from the cross-correlation function. Adaptive filters are known as effective methods for suppressing the interference signals but there is a problem to present their accurate performances in the PCL system because many literatures used the cross-correlation function and the ratio of input and output power as a measure of the performance analysis. In this paper, a performance analysis method is proposed to evaluate the performance of interference cancellation algorithms. By using the property that each component of the filter weight vector is adjusted to suppress the specific interference signal, a performance measure of the interference signal suppression is defined by a function of adaptive filter weights. Based on the proposed method, we compare the performance of the adaptive filters used in the PCL system. Simulation results show that the proposed method can be very effective for evaluating the performance of interference cancellation algorithms.

• Korean journal of communication and information
• /
• v.66
• /
• pp.28-58
• /
• 2014

South Korean broadcasting industry has been under a significant level of structural change since the permission of new general programming channels in the end of 2010. One of the most characteristic features of the change may be the exodus of core manpower from the in-house productions of major terrestrial broadcasters which have been maintaining their dominant power over broadcasting content market based on their systems of tight vertical integration. This paper sheds light on the presence of a purposeful 'mechanism design' that aims to the expansion of market logics in South Korean broadcasting sector by promoting commercial media conglomerates, and analyses how this external design has been actualized while being interlocked with various internal factors of the broadcasting industry. This paper shows that on the backdrop of the mechanism design, some of new media conglomerates has successfully provided various incentives in contrast with those disincentive of terrestrial broadcasters, which in turn, has facilitated the exodus of elite producers. This paper, however, raises a set of questions about whether this relocation process of creativity led by commercial media conglomerates would, in the long term, guarantee more opportunities and potentials for the producers, as promised. As part of conclusion, inherent problems of present mechanism design are highlighted.

• Korean Journal of Optics and Photonics
• /
• v.19 no.1
• /
• pp.68-72
• /
• 2008

Fiber-optic strain sensors based on Bragg reflection gratings produce the change of reflection spectrum when an external stress is applied on the sensor. To measure the Bragg reflection wavelength in high speed, an arrayed waveguide grating device is incorporated in this work. By monitoring the output power from each channel of the AWG, the peak wavelength corresponding to the applied strain could be obtained. To enhance the accuracy of the AWG wavelength interrogation system, a chirped fiber Bragg grating with a 3-dB bandwith of 5.4 nm is utilized. The high-speed response of the proposed system is demonstrated by measuring a fast varying strain produced by the damped oscillation of a cantilever. An oscillation frequency of 17.8 Hz and a damping time constant of 0.96 second are obtained in this measurement.

• Korean journal of communication and information
• /
• v.47
• /
• pp.120-147
• /
• 2009

The purpose of this paper is to promote bilateral friendly relations, the elements that hinder Hate Korea wave's(Kenkanryu) status and an analyzation of the characteristics of its causes and solutions for it. The Hate Korea wave is to be discussed in the fountain Hate Korea wave 2ch(2channel, ni channeru) acquaintances of information and representation to analyze the causes of this Japanese anti-Korean thinking. All of society should be aware of the differences and see what we have in common. I researched discussions of 2ch information and the content of other similar media. The expression was very violent. However, there was both general awareness of a gap between criticism and support. The gap was about what is not unusual on the Internet and not to be greatly concerned about. I also compares anti-Korean's awareness to Korea with general Japanese's, and finds that there are gap between them. For example by analyzing general Japanese's awareness we can find 18% of people who criticize the Hate Korea wave or have positive image of Korea. futhermore the proportion of anti-Korean contents in internet is not very high, so we don't have to worrying about the phenomenon seriously. but because of the following three points, there are sufficient needs to concern about the phenomenon constantly. First, sources of Hate Korea wave are traditional media. Second, the consumers of Hate Korea wave are mainly young generation who will make future relation of two countries. And last, Hate Korea wave include potential power to explode when certain conditions are met.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.10
• /
• pp.144-155
• /
• 1998

The array weights that will maximize the SNR for any type of noise environment are determined by the function of the antenna design configuration and the directions of receiving target and interference signals. The conventional SLCs(sidelobe cancellers) using the SNR maximization perform worst from the saturation of the receiving system of main channel when the main antenna has pattern with high gain at the arrival angle of strong interference. In this paper, the new SLC is accomplished by using two independent antenna architecture. Main antenna is implemented with adaptive nulling, which is used for rejecting high-power interference primarily. Auxiliary antenna is realized with adaptive array for receiving interference signal to be suppressed completely, which has a characteristics of sufficient gain for every direction. The new SLC is implemented with above both antennas. We show that the new SLC, which consists of the adaptive nulling main antenna and the adaptive array auxiliary antenna, is useful in reducing the effect of strong interference like jammer, because the adaptive nulling at main antenna prevents its receiver and signal processor for saturation by strong interference. The proposed SLC has improved SNR over the conventional SLCs. The improved SNR at sidelobe region is typically more than 7 dB for a given test signal. Moreover, it improves the SNR of about 20 dB under strong interference at mainlobe.