• Journal of computational fluids engineering
• /
• v.10 no.2
• /
• pp.1-6
• /
• 2005

The HANARO, a multi-purpose research reactor of 30 MWth, open-tank-in-pool type, has been under normal operation since its initial criticality in February, 1995. The HANARO is composed af inlet plenum, grid plate, core channel with flow tubes and chimney. The reactor core channel is located at about twelve meters (12 m) depth of the reactor pool and cooled by the upward flow that the coolant enters the lower inlet of the plenum, rises up through the grid plate and the core channel and comes out from the outlet of chimney. A fission moly guide tube is extended from the reactor core to the top of the reactor chimney for easily loading a fission moly target under the reactor normal operation. But active coolant through the core can be quickly raised up to the top of the chimney through the guide tube by jet flow. This paper describes an analytical analysis that is the study of the flow behavior through the guide tube under reactor normal operation and unloading the target. As results, it was conformed through the analysis results that the flow rate, reduced to about fourteen kilogram per second (14 kg/s) from the original flow rate of sixteen point three kilogram per second (16.3 kg/s) did not show the guide tube jet.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.96-103
• /
• 2000

In this study, evaporation heat transfer tests were conducted in flat aluminum multi-channel tubes using R-22. Two internal geometries were tested ; one with smooth inner surface and the other with micro-fins. Data are presented for the following range of variables ; vapor quality $(0.1{\sim}0.9)$, mass flux$(100{\sim}600kg/m^2s)$ and heat flux$(5{\sim}15kW/m^2)$. The micro-tin tube showed higher heat transfer coefficients compared with those of the smooth tube. Results showed that, for the smooth tube, the effects of mass flux, quality and heat flux were not prominent, and existing correlations overpredicted the data. For the micro-fin tube at low quality, the heat transfer coefficient increased as heat flux increased. However, the trend was reversed at high quality Kandlikar's correlation predicted the low mass flux data, and Shah's correlation predicted the high mass flux data. The heat transfer coefficient of the micro fin tube was approximately two times larger than that of the plain tube. New correlation was developed based on present data.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.3
• /
• pp.33-39
• /
• 2019

This study analyzes the content of YouTube channel "Cream Heroes" dealing pet(cat) produced in South Korea currently. Due to the advance of science and technology in the 21 century, the commons are able to independently upload their own content after filming videos, and it is called One Person Media. Unlike existing One Person Media that contains provocative and violent factors, "Cream Heroes" is sound content that shows various features of cats. Specifically, this study explores how and why "Cream Heroes" is popular via content analysis. Throughout this, it studies not only the trait of popular YouTube channel, but also proposes the proper environment of One Person Media.

• Nuclear Engineering and Technology
• /
• v.30 no.3
• /
• pp.262-272
• /
• 1998

The experiences and causes of pressure tube cracking accidents in the CANDU reactors and the development of the fuel channel at AECL(Atomic Energy Canada Limited) have been described. Most of the accidents were caused by Delayed Hydride Cracking(DHC). In the cases of the Pickering units 3&4 and the Bruce unit 2, excessive residual stresses induced by an improper rolled joint process played a role in DHC. In the Pickering unit 2, cracks formed by contact between the pressure and calandria tubes due to the movement of the garter spring were the direct cause of the failure. To extend the life of a fuel channel, several R&D programs examining each component of the fuel channel have been carried out in Canada. For a pressure tube, the main concern is focused on changing the fabrication processes, e.g., increasing cold working rate, conducting intermediate annealing and adding a third element like Fe, V, and Cr to the tube material. In addition to them, chromium plating on the end fitting and increasing wall thickness at both ends of the calandria tube are considered. There has also been much interest in the improvement of fuel channel performance in our country and several development programs are currently under way.

• Journal of Information Technology Applications and Management
• /
• v.31 no.3
• /
• pp.1-18
• /
• 2024

This study analyzed the impact of YouTube creator characteristics and channel access factors on the intention to continue watching content, noting that the development of the digital media environment has diversified media audiences' content preferences and access routes. Specifically, we analyzed the effects of YouTube creator trustworthiness, attractiveness, familiarity, and social influence, as well as the effects of recommendation services on perceived usefulness, perceived ease, and perceived enjoyment. The study found that creator credibility and recommendation service had a positive impact on the perceived usefulness of content, while intimacy and charm were important factors in increasing the easy of use and playfulness of content. These perceived usefulness, ease, and playfulness also had a strong positive impact on users' intention to continue watching the channel. This suggests that trust and intimate relationships with creators and appropriate content recommendations play an important role in increasing user satisfaction and channel persistence. The significance of this study's analysis of creator and channel access factors based on the extended technology acceptance model is that it shows the potential for extending and applying the existing technology acceptance model to the digital content environment.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.7
• /
• pp.649-658
• /
• 2005

Flow condensation heat transfer coefficients (HTCs) of R22, R410, Propane (R290) were measured inside a horizontal 9 hole aluminum multi-channel flat tube. The main test section in the refrigerant loop was made of a 0.53m long multi-channel flat tube of hydraulic diameter of 1.4 mm. Refrigerant was cooled by passing cold water through an annulus surrounding the test section. Data were obtained in qualities of $0.1\~0.9$ at mass flux of $200\~400kg/m^2s$ and heat flux of $7.3\~7.7kW/m^2$ at the saturation temperature of $40^{\circ}C$. All popular heat transfer correlations in single-phase subcooled liquid flow and flow condensation originally developed for large single tubes predicted the present data of the multi channel flat tube within $25\%$ deviation when effective heat transfer area was used in determining experimental data. This suggests that there is little change in flow characteristics and patterns when the tube diameter is reduced down to 1.4 mm diameter range. Hence, a modified correlation based on the present data was proposed which could be applied to small diameter tubes with effective heat transfer area. The correlation showed a mean deviation of less than $20\%$ for all data.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.249-255
• /
• 2005

Flow condensation heat transfer coefficients(HTCs) of R22, R4IO, Propane(R290) were measured inside a horizontal 9 hole aluminum multi-channel flat tube. The main test section in the refrigerant loop was made of a 0.53 m long multi-channel flat tube of hydraulic diameter of 1.4 mm. Refrigerant was cooled by passing cold water through an annulus surrounding the test section. Data were obtained in qualities of 0.1 ${\sim}$ 0.9 at mass flux of $200{\sim}400$ $kg/m^2s$ and heat flux of $7.3{\sim}7.7$ $kW/m^2$ at the saturation temperature of $4^{\circ}C$. All popular heat transfer correlations in single-phase subcooled liquid flow and flow condensation originally developed for large single tubes predicted the present data of the multi channel flat tube within 25% deviation when effective heat transfer area was used in determining experimental data. This suggests that there is little change in flow characteristics and patterns when the tube diameter is reduced down to 1.4 mm diameter range. Hence, a modified correlation based on the present data was proposed which could be applied to small diameter tubes with effective heat transfer area. The correlation showed a mean deviation of less than 20% for all data.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1835-1840
• /
• 2004

The HANARO, a multi-purpose research reactor of 30 MWth, open-tank-in-pool type, has been under normal operation since its initial criticality in February, 1995. The HANARO is composed of inlet plenum, grid plate, core channel with flow tubes and chimney. The reactor core channel is located at about twelve meters (12 m) depth of the reactor pool and cooled by the upward flow that the coolant enters the lower inlet of the plenum,. rises up through the grid plate and the core channel and comes out from the outlet of chimney. A guide tube is extended from the reactor core to the top of the reactor chimney for easily un/loading a target under the reactor normal operation. But active coolant through the core can be quickly raised up to the top of the chimney through the guide tube by a jet flow. This paper describes an analytical analysis that is the study of the flow behavior through the guide tube under reactor normal operation and unloading the target. As results, it was conformed through the analysis results that the guide jet is suppressed under the top of the chimney after modifying the orifice diameter of 37.5 mm to 31 mm.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.7
• /
• pp.575-583
• /
• 2002

In this study, condensation heat transfer tests were conducted in flat aluminum multi-channel tubes using R-410A, and the results are compared with those of R-22. Two internal geometries were tested; one with a smooth inner surface and the other with micro-fins. Data are presented for the following range of variables; vapor quality (0.1~0.9), mass flux (200~600 kg/$m^2$s) and heat flux (5~15 ㎾/$m^2$). Results show that the effect of surface tension drainage on the fin surface is more pronounced for R-22 than R-410A. The smaller Weber number for R-22 may be responsible. For the smooth tube, the heat transfer coefficient of R-410A is slightly larger than that of R-22. For the micro-fin tube, however, the reverse is true. Possible reasoning is provided considering the physical properties of the refrigerants. For the smooth tube, a correlation of Akers et at. type predicts the data reasonably well. For the micro-fin tube, the Yang and Webb model was modified to correlate the present data.

• Management & Information Systems Review
• /
• v.39 no.3
• /
• pp.127-140
• /
• 2020

This study conducted analysis of YouTube channels by domestic companies as the marketing strategies of domestic companies vary due to the rapid growth of the Internet and YouTube channels. The YouTube channel analysis analyzed the number of subscribers, plays, videos and classifications of domestic companies on YouTube channels, the top 100 domestic companies in the YouTube ranking site "Company/Official. The analysis showed that 4.53 million companies had the largest number of subscribers, Samsung mobile, 544.69 million circuit Samsung mobile, and 11,416 League of Legends-Korea channels had the largest number of videos. The most product classification showed that food/dining companies were engaged in a lot of YouTube activities. The use of YouTube, which is rapidly growing in companies through analyzing YouTube channels from the perspective of a company's new marketing strategy, is a new tool for integrated marketing communications. It is expected that the YouTube channel, which enables two-way communication of companies' marketing strategies, will be used as basic data when producing YouTube content in the future.