• 한국자동차공학회논문집
• /
• 제15권1호
• /
• pp.186-192
• /
• 2007

In general, pulsation damper is installed in fuel rail for conventional MPI engine to decrease undesirable noise in vehicle cabin room. However, pulsation damper is so expensive that there are prevailing studies to reduce fuel pressure pulsations with integrated damping effect. This paper is one of basic studies for development of fuel rail to abate pulsations with self-damping effect. Primarily, the pressure pulsation characteristics was investigated with aspect ratio of cross section, wall thickness, and materials of fuel rail. A high aspect ratio or thin wall was found to absorb the pressure pulsations effectively. But volume effects on the fuel pressure pulsation reductions were not especially significant than cross section effects because volume increment rate is larger than pressure pulsation reduction rate. The fuel rail made of aluminum is effective for reduction of pressure pulsation than that of low-carbon steel. Pressure change period increases on the basis of same lengths of supply line and fuel rail as the volume is enlarged and/or the thickness of wall is thinned.

• 열처리공학회지
• /
• 제34권3호
• /
• pp.107-115
• /
• 2021

Al-Si coated boron steel has been widely used as commercial hot stamping steel. When the steel is heated at 900~930℃ for 5 min in an electric furnace, thickness of the coating layer increases as a consequence of formation of intermetallic compounds and diffusion layer. The diffusion layer plays an important roll in blunting the propagation of crack from coating layer to base steel. Change in microstructure and coating layer of Al-Si coated boron steel after conductive heating with higher heating rate than electric furnace has been investigated in this study. Conductive-heated steel showed the martensitic structure with vickers hardness of 505~567. Both intermetallic compounds in coating layer and diffusion layer were not observed in conductive-heated steel due to rapid heating. It has been found that the conductive-heating consisting of rapid heating to 550℃ which is lower than melting point of Al-Si coating layer, slower heating to 900℃, and then 1 min holding at 900℃ is effective in forming intermetallic compound in coating layer and diffusion layer.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.1165-1168
• /
• 2002

This paper presents a neural network based self-tuning fuzzy PID control scheme with variable learning rate for sensorless vector controlled induction motor drives. MRAS(Model Reference Adaptive System) is used for rotor speed estimation. When induction motor is continuously used long time. its electrical and mechanical parameters will change, which degrade the performance of PID controller considerably. This paper re-analyzes the fuzzy controller as conventional PID controller structure, introduces a single neuron with a back-propagation learning algorithm to tune the control parameters, and proposes a variable learning rate to improve the control performance. The proposed scheme is simple in structure and computational burden is small. The simulation using Matlab/Simulink and the experiment using DS1102 board show the robustness of the proposed controller to parameter variations.

• 경영과정보연구
• /
• 제1권
• /
• pp.413-443
• /
• 1997

In today's hospital-management, information system and the information by it will be a necessary administrative materials of organization with man-power, funds, equipment and resources. This study is for figuring out steps to utilize information-system, an important strategy to grow the hospital applying to the change of surroundings, improving the service for patients, accelerating medical examination, improving it in quality and suggesting a basis be able to manage it effectively by putting information system in practice such as economic effect by shorting time and the effect of medical study by computerizing clinical data. And the result of it is as follows: From the Nolan's 6 step - model about the degree using information system in hospital-management, the 1st group of hospital-size came to 1st and 2nd step, the 2nd group to the 3rd and 4th step and the 3rd group to the 5th and 6th step, which correspond to the survey- results that information system increases with the size of the hospital to propagation, regulation and integration step and that the number of the hospital developing to the step managing information is increasing.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.31-36
• /
• 2001

As a part of micro engine development feasibility estimation was done through fabrication and test of down scaled combustor and MEMS fabricated spark electrode. In an experimental observation of the down scaled combustion phenomena where flame propagation was observed by optical method and pressure change in combustor which gives the information about the reaction generated thermal energy was recorded and analyzed. Optimal combustor scale was derived to be about 2mm considering increased heat loss effect and thermal energy generation capability. Through the fabrication and discharge test of MEMS electrode effects of electrode width and gap was investigated. Electrode was fabricated by thick PR mold and electroplating. From the result discharge voltage characteristic in sub millimeter scale electrode having thickness of $40{\mu}m$ was obtained. From the result base technology for design and fabrication of micro engine was obtained.

• Journal of Welding and Joining
• /
• 제13권2호
• /
• pp.60-67
• /
• 1995

The factors affecting on the fatigue strength of spot_welded specimens have been studied. The influence of initial overloads on the fatigue life of spot_welded tensile_shear specimens is investigated by considering fatigue crack initiation and crack propagation. The change of strain range and the influence of initial overload are correlated on the basis ol strain results. The results of this study are as follows. l) The initial absolute strain range decreased with initial overloads increase, and absolute strain range decreased before transformation of waveform of strain, but increased after transformation of waveform of strain. 2) In case of subsequent point of inflection of offset strain, the increment of this strain decreased with initial overload increase. 3) As initial overloads increase, the deformation behavior of spot welded parts is restricted after overloading.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2003년도 ISIS 2003
• /
• pp.644-647
• /
• 2003

This paper describes a neural network based machine vision system designed for inspecting yellow beans in real time. The system consists of a camera. lights, a belt conveyor, air ejectors, and a computer. Beans are conveyed in four lines on a belt and their images are taken by a monochrome line scan camera when they fall down from the belt. Beans are separated easily from their background on images by back-lighting. After analyzing the image, a decision is made by a multilayer artificial neural network (ANN) trained by the error back-propagation (EBP) algorithm. We use the global mean, variance and local change of gray levels of a bean for the input nodes of the network. In an our experiment, the system designed could process about 520kg/hour.

• 대한기계학회논문집B
• /
• 제29권9호
• /
• pp.971-978
• /
• 2005

Effects of inlet distorted flow on performance, stall and surge are experimentally investigated for a high-speed centrifugal compressor. Tested results for the distorted inlet flow cases are compared with the result of the undistorted one. The performance of compressor is slightly deteriorated due to the inlet distortion. The inlet distortion does not affect the number of stall cell and the propagation velocity. It also does not change stall inception flow rate. However, as the distortion increases, stall starts at the higher flow rate for low speed and at the lower flow rate for high speed. For 50,000 rpm stall occurrs as the flow rate decreases, however disappears fur the smaller flow rate. This is due to the interaction of surge and stall. After the stall and surge interact, the number of stall cell decreases.

• 한국수산과학회지
• /
• 제2권1호
• /
• pp.83-86
• /
• 1969

The present investigations were made with the purpose of elucidating the seasonal variation in total nitrogen content of Gelidium amansii. Monthly samples were collected from the sea near pusan, from August 1957 to June 1959. The results obtained have been summarized as follows: The maximum total nitrogen content of Gelidium amansii was observed during the months of January and February, and the minimum content was observed in June and July Thus the total nitrogen content of Gelidium amansii exhibited a considerable periodic change throughout the year. The recommended harvest time of Gelidium amansii with regard to total nitrogen content, is from May to October, but on the other hand the proper harvest time is from May to June, with respect to the season of spore-formation and its propagation.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2001년도 추계학술대회 학술발표 논문집
• /
• pp.271-274
• /
• 2001

Recently, most vehicles has the Automatic transmission system as their transmission system. The automatic transmission system operates with fixed shift patterns. In the opposite of manual operation, it is easy and convenient for driving. Though these merit, the system can not evaluate the driver's intension because of usage of fixed shift pattern, To consider driver's intension, we must consider both the driving intensity of driver and the status of vehicle. In this paper, we developed flexible automatic transmission system by using the proposed moduled neural networks which can learn the status of the vehicle and driver's intensity As a result, we compare the transmission system using fixed shift pattern and the proposed transmission system and show the good performance in the change of shift position.