• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.546-552
• /
• 2010

The achievement of high gas permeability is a key factor in the development of porous SiC ceramics for applications of hot gas filter, vacuum chuck, and air spindle. However, few reports on the gas permeability of porous SiC ceramics can be found in the literature. In this paper, porous SiC ceramics were fabricated at temperatures ranging from $1600^{\circ}C$ to $1800^{\circ}C$ using the mixing powders of SiC, silicon, carbon and boron as starting materials. In some samples, expanded hollow microspheres as a pore former were used to make a cellular pore structure. It was possible to produce Si bonded SiC ceramics with porosities ranging from 42% to 55%. The maximum bending strength was 58MPa for the carbon content of 0.2 wt% and sintering temperature of $1700^{\circ}C$. The increase of air permeability was accelerated by addition of hollow microsphere as a pore former.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.605-609
• /
• 2001

Low density ceramic supporter was prepared by using fly ash as a starting material for the application to the biological aerated filter (BAF) system, and the effect of additives and sintering atmosphere on the apparent and bulk density of the carrier was examined. Borax, Na$_2$O and glass powders were added to produce liquid phase. The density of the supporter decreased as the amount of borax increased. The bulk density of 0.79 g/㎤ and the apparent density of 1.10 g/㎤ were obtained when the fly ash with 15% of borax was sintered at 116$0^{\circ}C$ for 15 minutes. The density also decreased as the plate glass powders past through 22${\mu}{\textrm}{m}$ size were mixed. When the fly ash with 12% of grass powder was sintered at 128$0^{\circ}C$ for 10 minutes, the bulk and apparent density were 0.90g/㎤ and 1.00 g/㎤, respectively. Apparent density of 1.6~1.8g/㎤ was obtained when the fly ash was sintered at 120$0^{\circ}C$ in a weak reducing atmosphere. By maintaining the reducing atmosphere and sintering at a high heating rate, the liquid phase was farmed from the reduced composition of fly ash. This resulted in the formation of closed pores that enabled the low apparent density.

• Journal of the Korean Ceramic Society
• /
• v.49 no.2
• /
• pp.179-184
• /
• 2012

The size of various alumina ceramics used in semiconductor and display industry is required to increase with increase in wafer and panel size. In this research, large alumina ceramics were fabricated by uniaxial pressing, cold isostatic pressing and filter pressing with commercial powder and thereafter sintering at $1600^{\circ}C$ in gas furnace. The large alumina ceramics exhibited dense microstructure corresponding to 98.5% of theoretical density and 99.8% of high purity. The impurities and microstructural defects of the alumina were found to influence the resistance and dielectric properties. The volume resistances in these four aluminas were almost the same while the pure alumina was higher value. The dielectric constant, dielectric loss and dielectric strength of aluminas were placed within the range of 10.3~11.5, 0.018~0.036, and 10.1~12.4 kV/mm, respectively.

• Journal of the Korean Ceramic Society
• /
• v.51 no.2
• /
• pp.132-137
• /
• 2014

The study was performed with low-grade limestone, which is used to make cement or is disposed of due to its low CaO content. In this study, the optimal condition of limestone with which to manufacture precipitated calcium carbonate (PCC) and limestone in fiber was determined through in-situ reactions. The best firing condition is with slaked lime with rapid cooling after 2 h of firing at $1000^{\circ}C$. In addition, the content of CaO can be increased by sorting the low-grade limestone using a 200 mesh filter, and the optical quality of old newspaper (ONP) was similar when using both low-grade and high-grade limestone. Also, controlling the particle size of PCC is an important factor pertaining to the optical characteristics of paper.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.2
• /
• pp.168-177
• /
• 1998

The effects of the regeneration parameters such as inlet gas temperature, space velocity, oxygen concentration of the exhaust gas, and initial particulate loading on the oxidation of the particulate inside ceramic cordierite filter have been investigated through an engine experiment. As the inlet gas temperature increases, the remarkable filter temperature occurs owing to the rapid combustion rate. Though the higher space velocity affirms the safe regeneration, it also requires much fuel consumption of the burner. For that reason, the space velocity should be compromised considering the fuel economy. The excessive accumulation of the particulate may cause undesirable regeneration temperatures inside filer even under the optimized regeneration condition. The inlet gas temperature should be selected to overcome the variation of the oxygen concentration which is inherent feature of the diesel engine. It is the most important factor in the regeneration control techniques.

• Korean Journal of Optics and Photonics
• /
• v.19 no.2
• /
• pp.140-143
• /
• 2008

The integrated external cavity laser has been fabricated with a 1550 nm FP-LD, an optical filter, a micro ball lens and accurate ceramic blocks using a micro-block stacking (MBS) technique. The integrated external cavity laser module whose size is only $2.0{\times}2.1{\times}0.7\;mm^3$ has been mounted on the TO-CAN package. For the case of the 1.8% transmission filter, the single mode characteristic has been obtained with the optical power of -27.1 dBm and the SMSR of 31.7 dB.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1999.06a
• /
• pp.253-269
• /
• 1999

The development of telecommunication and information technology requires to develop new piezoelectric materials with small size, low impedance, wide pass band width and high thermal stability of frequency. Langasite (La3Ga5SiO14) single crystal has been researched substitute of quartz and LiNbO3 for the applications of SAW filter, BAW filter and resonator. Its single crystal growth has been carried out by Czochralski Method. So, in order to get single crystal with higher quality, in this study, lnagasite (La3Ga5SiO14) single crystal was grown by using Floating Zone (FZ) method and characterized. For the growth of langasite single crystals, the langasite powder was synthesized at 135$0^{\circ}C$ for 5hrs and the feed rod was sintered at 135$0^{\circ}C$ for 5hrs. The growing rate was 1.5mm/h and the rotation speed was 15 rpm for an upper rotation and 13 rpm for a lower rotation. In order to prevent the evaporation of gallium oxide, Ar and O2 gas mixture was flowed. The growth direction was analyzed by Laue back-scattered analysis. The composition of grown crystal was analyzed suing XRD and WDS. The electrical properties of grown crystal at various frequencies and temperature were discussed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.632-635
• /
• 2008

In this paper, a diplexer circuit to separate GSM/CDMA band is designed using a LTCC (Low Temperature Cofired Ceramic) multi-layer technology. In order to increase a integration capability of the diplexer, it is designed in 6-layer LTCC sunstrate with a elative dielectric constant of 7.2 using 3-dimensional (3-D) multi-layer inductors and capacitors. The size of the designed diplexer including CB-CPW pads is $3,450{\times}4,000{\times}600{\mu}m^3$. An insertion loss (IL) and return loss of GSM band are less than -0.23dB and -10dB, respectively. In the case of CDMA band, the IL of -0.53dB and RL of below -10dB are archieved.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.91-95
• /
• 2002

A very small size BPF is realized using LTCC Multilayer technology. A λ/4 resonator with shunt-to-ground loaded capacitor is used to shorten resonator length and achieve higher qualityfactor. Also this resonator enable BPF to improve out-of-band rejection. Coupling coefficients between coupled stripline resonators and external qualityfactor of a resonator are derived and apply to the filter design. The measured results show a good agreement with the simulation.

• International Journal of Automotive Technology
• /
• v.6 no.2
• /
• pp.95-105
• /
• 2005

Diesel engines have low specific fuel consumption, but high particulate emissions, mainly soot. Diesel soot is suspected to have significant effects on the health of living beings and might also affect global warming. Hence stringent measures have been put in place in a number of countries and will be even stronger in the near future. Diesel engines require either advanced integrated exhaust after treatment systems or modified engine models to meet the statutory norms. Experimental analysis to study the emission characteristics is a time consuming affair. In such situations, the real picture of engine control can be obtained by the modeling of trend prediction. In this article, an effort has been made to predict emissions smoke and NO$_{x}$ using cylinder combustion derived parameters and diesel particulate filter data, with artificial neural network techniques in MATLAB environment. The model is based on three layer neural network with a back propagation learning algorithm. The training and test data of emissions were collected from experimental set up in the laboratory for different loads. The network is trained to predict the values of emission with training values. Regression analysis between test and predicted value from neural network shows least error. This approach helps in the reduction of the experimentation required to determine the smoke and NO$_{x}$ for the catalyst coated filters.