• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.4
• /
• pp.293-297
• /
• 2010

We have studied the optical and electrical properties of a-IGZO thin films on the n-type semiconductor fabricated by RF magnetron sputtering method. The ceramic target was used in which $In_2O_3$, $Ga_2O_3$ and ZnO powder were mixed with 1:1:2 mol% ratio and furnished. The RF power was set at 25 W, 50 W, 75 W and 100 W as a variable process condition. The transmittance of the films in the visible range was above 80%, and it was 92% in the case of 25 W power. AFM analysis showed that the roughness increased as increasing RF power, and XRD showed amorphous structure of the films without any peak. The films are electrically characterized by high mobility above 10 $cm^2/V{\cdot}s$ at low RF power, high carrier concentration and low resistivity. It is required to study further finding the optimal process condition such as lowering the RF power, prolonging the deposition ratio and qualification analysis.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.161-161
• /
• 1999

In the field of material science, the interests and efforts to modify the surface of materials in agreement with the need of usage have been extensively increasing. he modification to improve the wettability of surface is very important is terms of adhesion, printing, etc. It is very difficult to modify metal surface into hydrophilic one. therefore, surfactant coating has been generally used in many cases. However, surfactant has disadvantages such as environmental problem, soluble in water. in this study, hydrophilic polymer films as alternative of surfactant were deposited on metal substrate by DC plasma polymerization. Hydrophilic polymer films deposited by DC plasma show many merits such as good wettability, stone adhesion to substrate, high resistance to most chemicals. Monomer gas and reactive gas were used as source plasma polymerization. Plasma polymerized films were fabricated with process parameters of deposition time, ratio of gas mixture, current, pressure, etc. Effects of these variables on wettability of plasma polymer films will be discussed. With XPS and FT-IR analyses of plasma polymeric films, the relation between wettability and chemical state of polymer films by DC plasma was investigated.

• Journal of Electrochemical Science and Technology
• /
• v.9 no.3
• /
• pp.212-219
• /
• 2018

Perovskite type ceramic membranes which exhibit dual ion conduction (proton and oxygen ion conduction) can permeate water and can aid solving operational problems such as temperature gradient and carbon deposition associated with a working solid oxide fuel cell. From this point of view, it is crucial to reveal water transport mechanism and especially the nature of the surface sites that is necessary for water incorporation and evolution. $BaCe_{0.8}Y_{0.2}O_{3-{\alpha}}$ (BCY20) was used as a model proton and oxygen ion conducting membrane in this work. Four different catalytically modified membrane configurations were used for the investigations and water flux was measured as a function of temperature. In addition, CO was introduced to the permeate side in order to test the stability of membrane against water and $CO/CO_2$ and post operation analysis of used membranes were carried out. The results revealed that water incorporation occurs on any exposed electrolyte surface. However, the magnitude of water permeation changes depending on which membrane surface is catalytically modified. The platinum increases the water flux on the feed side whilst it decreases the flux on the permeate side. Water flux measurements suggest that platinum can block water permeation on the permeate side by reducing the access to the lattice oxygen in the surface layer.

• Composites Research
• /
• v.26 no.1
• /
• pp.60-65
• /
• 2013

A nanolaminate consisting of alternate layers of aluminium oxide ($Al_2O_3$) (5 nm) and zirconium oxide ($ZrO_2$) (20 nm) was deposited at an optimized oxygen partial pressure of $3{\times}10^{-2}$ mbar by pulsed laser deposition. The nanolaminate film was analysed using high temperature X-ray diffraction (HTXRD) to study phase transition and thermal expansion behaviour. The surface morphology was investigated using field emission scanning electron microscopy (FE-SEM). High temperature X-ray diffraction indicated the crystallization temperature of tetragonal zirconia in the $Al_2O_3/ZrO_2$ multilayer-film was 873 K. The mean linear thermal expansion coefficient of tetragonal $ZrO_2$ was $4.7{\times}10^{-6}\;K^{-1}$ along a axis, while it was $13.68{\times}10^{-6}\;K{-1}$ along c axis in the temperature range 873-1373 K. The alumina was in amorphous nature. The FESEM studies showed the formation of uniform crystallites of zirconia with dense surface.

• Korean Journal of Materials Research
• /
• v.9 no.2
• /
• pp.163-167
• /
• 1999

LiNbO$_3$films were prepared by an rf-magnetron sputtering technique using sintered target containing potassium. The potassium was included to help to fabricate stoichiometric LiNbO$_3$film. Structural and electrical properties of thin films was investigated as a function of deposition condition. Optimum sputtering conditions were rf power of 100W, working pressure of 1m Torr and substrate temperature of 58$0^{\circ}C$. The thin film was grown to (012) preferred orientation. The dielectric constant of the thin film LiNbo$_3$ fabricated under optimum condition was 55 at 1MHz. Average grain size is about 200$\AA$ and roughness of the film is small enough to apply to optic devices.

• Korean Journal of Materials Research
• /
• v.13 no.12
• /
• pp.779-784
• /
• 2003

Nickel powders were obtained by various preparation methods, and their sintering characteristics were investigated. Nickel powders made by wet chemical process (WCP) had a higher surface area and more narrow size distribution than that of chemical vapor deposition (CVD) method. Nickel-oxide powders by the WCP method were prepared at $200^{\circ}C$ for 3 hr. The oxidation behaviour of nickel-oxide powder is similar with that of the CVD method. Nickel powders made by the WCP method showed a higher shrinkage in the range of $600^{\circ}C$∼$900^{\circ}C$ than that of commercial powder made by the CVD method. The similar results were observed on the surface microstructure of sintered bodies by SEM measurements.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.179-180
• /
• 2012

Aluminum alloys are widely known as non-ferrous metal with light weight and high strength. Consequently, these materials take center stage in the aircraft and automobile industry. The Al7075 aluminum alloy is based on the Al-Zn-Mg-Cu and one of the strongest wrought aluminum alloys. Aluminum nitride has ten times higher thermal conductivity($319W/m{\cdot}K$) than Al2O3 and also has outstanding electric insulation($1{\times}1014{\Omega}{\cdot}cm$). Furthermore, it has high mechanical property (430 MPa) even though its co-efficient of thermal expansion is less than alumina For these reasons, it has great possibilities to be used for not only the field which needs high strength lightweight but also electronic material field because of its suitability to be applied to the insulator film of PCB or wafer of ceramic with high heat conduction. This paper investigates the mechanical properties and corrosion behavior of aluminum alloy Al7075 deposited with aluminum nitride thin films To improve the surface properties of Al7075 with respect to hardness, and resistance to corrosion, aluminum nitride thin films have been deposited by pulsed DC reactive magnetron sputtering. The pulsed DC power provides arc-free deposition of insulating films.

• The Korean Journal of Ceramics
• /
• v.3 no.3
• /
• pp.182-186
• /
• 1997

Diamond-like carbon(DLC) films were deposited on silicon substreates by using an RF plasmaassisted CVD apparatus; the effects of deposition conditions such as CH4 gas pressure and substrate bias voltage on DLC film friction and wear were examined in both friction and scratch tests. In friction tests critical loads at which the friction coefficient increases abruptly depend on substrate bias voltages: critical loads deposited at a bias voltage of -100 V exceed those deposited at other bias voltages. Critical loads are correlated with DLC film hydrogen content. Critical DLC film loads in scratch tests depended considerably less than in friction tests. The friction coefficient of DLC films depends on neither substrate bias voltage nor CH4 gas pressure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.462-462
• /
• 2013

Gallium Oxide (Ga2O3) has been widely investigated for the optoelectronic applications due to its wide bandgap and the optical transparency. Recently, with the development of fabrication techniques in nanometer scale semiconductor materials, there have been an increasing number of extensive reports on the synthesis and characterization of Ga2O3 nano-structures such as nano-wires, nanobelts, and nano-dots. In contrast to typical vaporliquid-solid growth mode with metal catalysts to synthesis 1-dimensional nano-wires, there are several difficulties in fabricating the nanostructures by using sputtering techniques. This is attributed to the fact that relatively low growth temperatures and higher growth rate compared with chemical vapor deposition method. In this study, Ga2O3 chestnut burr were synthesized by using radio-frequency magnetron sputtering method. In contrast to typical sputtering method with sintered ceramic target, a Ga2O3 powder (99.99% purity) was used as a sputtering target. Several samples were prepared with varying the growth parameters, especially he growth time and the growth temperature to investigate the growth mechanism. Samples were characterized by using XRD, SEM, and PL measurements. In this presentation, the details of fabrication process and physical properties of Ga2O3 nano chestnut burr will be reported.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.6
• /
• pp.255-262
• /
• 2006

Pd-Cu alloy membrane for hydrogen separation was fabricated by sputtering and Cu reflow process. At first, the Pd and Cu was continuously deposited by sputtering method on oxidized Si support, the Cu reflow process was followed. Microstructure of the surface and permeability of the membrane was investigated depending on various reflow temperature, time, Pd/cu composition and supports. With respect to our result, Pd-Cu thin film (90 wt.% Pd/10 wt.% Cu) deposited by sputtering process with thickness of $2{\mu}m$ was heat-treated for Cu reflow The voids of the membrane surface were completely filled and the dense crystal surface was formed by Cu reflow behavior at $700^{\circ}C$ for 1 hour. Cu reflow process, which is adopted for our work, could be applied to fabrication of dense Pd-alloy membrane for hydrogen separation regardless of supports. Ceramic or metal support could be easily used for the membrane fabricated by reflow process. The Cu reflow process must result in void-free surface and dense crystalline of Pd-alloy membrane, which is responsible for improved selectivity oi the membrane.