• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2009년도 춘계학술발표논문집
• /
• pp.450-453
• /
• 2009

Compositional design and optimization of processing parameters are key factors for controlling and improving the properties of SiC-based electroconductive ceramic composites. Compare economic estimation of SiC ceramic heater with sheathe heater are as followings. (1) Temperature rising time of sheath heater is 1.1 times faster than SiC ceramic heater. (2) Heating insulation of SiC ceramic heater is 2.7 times larger than sheath heater. If SiC ceramic heater is one body type of a product application, contact resistance will decrease. I think that temperature initial rising time is faster than now. The more SiC ceramic heater is used for a long time, the more economic benefit is larger in the view point of heat insulation.

• 한국세라믹학회지
• /
• 제19권2호
• /
• pp.95-100
• /
• 1982

Instead of barium carbonate, domestic barite was used as the flux in manufacturing theinsulating porcelain. To avoid the problems arising from the decomposition of barite in the body during firing, BaO.$Al_2O_3$ was synthesized at $1300^{\circ}C$ for 5 hours. synthetic BaO.$Al_2O_3$ was mixed with other materials such as kaoline, alumina, clay, dolomite. The RO content (CaO. MgO. BaO) of the batches was varied from range of 4 to 14wt. % at 2wt. % - intervals, and firing temperature was varied from 1280 to 140$0^{\circ}C$-at 4$0^{\circ}C$ intervals The properties such as water absorption, bulk density. mechnical strength, specific resistance, and linear shrinkage were measured. The body containing 12 wt.% of RO content showed the satisfactory for the application in the Fixed Carbon Film Resistor.

• 한국세라믹학회지
• /
• 제14권1호
• /
• pp.12-18
• /
• 1977

In our former paper, tremolitic talc, -wollastonite-clay system was studied. In this study blast furnace slag was used(B.F.S.) instead of wollastonite for developing a fast-firing wall tile body. The wall tile bodies consisting of tremolitic talc and B.F.S. asmajor constituents have been fired in the temperature range 1000-120$0^{\circ}C$. Some of these bodies have showed good properties for wall tile manufacture. According to the increased content of B.F.S the fired bodies have showed the decreased thermal expansion which was resulted from the fact that the amounts of diopside and anorthite were gradually increased and those of quartz relatively decreased. Being reasonable in low price and thermo-stable properties tremolitic talc and B.F.S. will be good materials for the fast-firing tile body.

• 대한치과기공학회지
• /
• 제45권3호
• /
• pp.81-86
• /
• 2023

Purpose: This study aimed to observe the effect of laminate veneer on patient's teeth based on the manufacturing of laminate veneer restorations, which are produced by fabricating a ceramic cast body using IPS Empress, a pressure casting method and then forming the veneer by layering. Subsequently, we assessed the potential of its clinical application. Methods: This study discusses and preserves various treatment plans, such as diagnostic wax-up and treatment room diagnosis, for patients who visit the hospital to improve the appearance of teeth due to diastema of maxillary teeth, inexperienced resin filling, lack of esthetics, and external teeth. A ceramic cast body is constructed using IPS Empress, which is an effective and aesthetic restoration pressure casting method to restore the veneer with a laminate made by layering. Results: Compared with the preoperative state, the frontal view of the patient after the final restoration showed the formation of a natural smile line; the space between the central and lateral incisors was filled in synchronously with the adjacent teeth. In addition, the emergence profile is maintained by reducing the over-contour as much as possible. Conclusion: The patient's quality of life is improved by providing them with a satisfactory natural smile.

• 한국세라믹학회지
• /
• 제52권3호
• /
• pp.186-191
• /
• 2015

Tribological properties of whiteware with various transparent glazes, which have different composition and microstructure, were investigated. The wear resistance and friction behavior of the glazed whiteware are a very important aspect if the whiteware is used as tableware and for sanitation purposes. Generally, the wear property is influenced by the microstructure and surface morphology of the material. The whiteware specimens with two kinds of transparent glazes were fabricated by using the commercially available porcelain body. Furthermore, the commercial tableware, such as bone china, and traditional tableware were also examined as reference materials. All of the specimens showed that different pore structures might affect the mechanical and tribological properties. It seems that the wear resistance of whiteware is substantially related to the pore size and distribution of glaze rather than the hardness value of the specimen.

• 한국세라믹학회지
• /
• 제42권11호
• /
• pp.770-776
• /
• 2005

Hardening and hydroxyapatite(HAp) formation behavior of the bioactive cements in the system of $CaO-SiO_{2}-P_{2}O_{5}$ glasses and the corresponding glass-ceramics were studied. DCPD (Dicalcium Phosphate Dihydrate: $CaHPO_4{\cdot}2H_2O$) and DCPA (Dicalcium Phosphate Anhydrous: $CaHPO_4$) were developed when the prepared glass and glass-ceramic powders were mixed with three different solutions. The DCPD and DCPA transformed to HAp when the cement was soaked in Simulated Body Fluid (SBF), and this HAp formation strongly depended on the releasing capacity of $Ca^{2+}$ ions from the cements. The glass-ceramic containing apatite showed fast setting, but no HAp formation was observed because no $Ca^{2+}$ ions were released from this glass-ceramics. The compressive strength of the cements increased with reaction time in SBF until all DCPD and DCPA transformed to HAp.

• 한국세라믹학회지
• /
• 제26권6호
• /
• pp.850-854
• /
• 1989

The elastic moduli and dissolution rates of 15 glasses with different mole ratios of sodium-magnasium-phosphate as potential non-toxic biomaterials were investigated. In this study, a 3-pint bending test, sonic resonance technique, and theoretical calculation were used to evaluate the modulus of elasticity. The dissolution rates at 37$^{\circ}C$(human body temperature) were determined by the measurement of mass changes in each sample for 24 weeks.

• 한국세라믹학회지
• /
• 제55권2호
• /
• pp.126-134
• /
• 2018

Using aqueous solution free radical polymerization with glacial acrylic acid (GAA), maleic anhydride (MA) and sodium methallyl disulfonate (SMADS), a novel linear polycarboxylate dispersant was synthesized for ceramics. Dispersant linear structural characterization was done by FTIR, $^1H$ NMR, HPLC and GPC, and the ratio of monomers was determined using an orthogonal experiment. This research is focused on the effects of polymerization temperature, monomer mole ratios and dosage of initiator on ceramic slurry viscosity with linear polycarboxylate dispersant for ceramic dosage rate of 0.30% (based on dry slurry), all of which were investigated by single factor test. The best polymerization conditions for linear GAA-MA-SMADS are when n(AA) : n(MA) : n(SMADS) equals 3.0 : 1.0 : 0.5, the molecular weight of the polymer is 4600 daltons, the initiator sodium persulfate accounts for 7% of the total mass of polymerized monomers, the polymerization temperature is $90^{\circ}C$ and the reaction time is 2 h. The ceramic body slurry viscosity drops from $820mPa{\cdot}s$ to $46mPa{\cdot}s$ when the concentration of the polycarboxylate dispersant is 0.30%.

• 한국세라믹학회지
• /
• 제12권4호
• /
• pp.29-36
• /
• 1975

Korean clinochlore, kaolin, pyrophillite and a technical grade of alumina have been used to investigate the effects of Al2O3 on the formation and properties of cordierite bodies. The body compositions were formulated from the proper proportions of the above raw materials to cover the range of composition from the point corresponding to the stoichiometric formula of cordierite, bythe consecutive increasment of 0.2mol. Al2O3, toward the apex of Al2O3 on the MgO-Al2O3-SiO2 triaxial diagram. Each of bodies was fired with the elevated temperatures from 110$0^{\circ}C$ to 140$0^{\circ}C$ by 5$0^{\circ}C$ interval. Linear shrinkage and water absorption were taken as measures for the firing range of the bodies. The formation of cordierite was estimated from the comparative study of X-ray diffraction and dilatometry of the fired bodies. The formation of a large amount of cordierite was initiated about 120$0^{\circ}C$. The content of Al2O3 exceeded up to 0.8 mol. comparing to the stoichiometric formula of cordierite broadens the firing range of the body.

• 열처리공학회지
• /
• 제36권4호
• /
• pp.215-222
• /
• 2023

3Y-TZP (3 mol% yttria-stabilized tetragonal zirconia polycrystals, 3Y-TZP) ceramics are emerging as dental implant materials due to their superior optical and mechanical properties as well as excellent biophysical properties, in spite of low bioactivity. In this study, we investigated to sintered properties and microstructural defects of dental zirconia implants fabricated by ceramic injection molding and post-HIP (Hot isostatic pressing) processing and analyzed the processing parameters related with the obtainment of its high sinterd density. Sintered and microstructural parameters, i.e, apparent density, grain size and phase composition of zirconia implants fabricated by injection molding were dependent on the fixtute size and implant type. Maximum sintered density of 99.2% and minimum grain size of 0.3-0.4 ㎛ were obtained from large-scaled 2-body sample. In 1-body ceramic implant, high sintered density of 99.5% was obtained, but it had a little monoclinic phase and wide grain size distribution.