• ETRI Journal
• /
• v.33 no.1
• /
• pp.132-135
• /
• 2011

In this letter, we study the contemporary technologies for making ferroelectric films and the possibility of using the oscillator model of PZT-22 to analyze its ferroelectric properties. The material showed permittivity dispersion at 65 KHz and 88.5 KHz. We obtained relative attenuation ${\gamma}$, relaxation time ${\tau}$, and ${\varepsilon}_{max}$ of the material as 0.0008319, 0.5 s, and 603.438, respectively.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.215-216
• /
• 2006

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.3
• /
• pp.541-546
• /
• 2010

The push-push DRO(dielectric resonator oscillator) using a multi-layer structure of LTCC(low temperature co-fired ceramic) fabrication is designed. After the single DRO of series feedback type in the center frequency of 8GHz is designed, the push-push DRO in the center frequency of 16GHz including the Wilkinson power combiner is designed. The bias circuit affecting the size of oscillator are embedded in the intermediate layer of the LTCC multi-layer substrate. As a result, the large reduction in the size of VCO is obtained compared to the general oscillator on the single layer substrate. Experimental results show that the fundamental and third harmonics suppression are above 15dBc and 25dBc, respectively, and phase noise characteristics of the push-push DRO presents performance of -102dBc/Hz@100KHz and -128dBc/Hz@1MHz offset frequencies from carrier.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.1
• /
• pp.61-64
• /
• 2001

VCO(Voltage Contolled Oscillator) is one of the main components governing the size, performance and power consumption of telecommunication devices. As the devices become much smaller, YCO need to hove much smaller size with better characteristics. Buried type passive components of L, C, R were developed previously and the structure of these components are good for minimizing the size of VCO. Our own library of passive components is used in simulation and measurement circuit designed by ourselve. In structure of multi-layered VCO, some components governing the characteristics of VCO are selected and placed on the top of oscilltor for the good tuning process. In resonator part, the stripline structure and low loss glass/ceramic material are used to get higher Q value. In our research, a VCO oscillates in the 2.3~2.36 GHz band is developed.

• KSBB Journal
• /
• v.13 no.5
• /
• pp.477-482
• /
• 1998

A biosensor with PZT piezoelectric ceramic crystal was developed for the detection of formaldehyde gas. Poled PZT piezoelectric ceramic disk was made from ZrO2, TiO2 and Nb2O5, together with the addition of PbO and polyvinyl alcohol, through various processes of mixing, calcination drying, crushing, forming, sintering, polishing, ion coating and poling. Oscillator circuit of sensor was made of operational amplifier(AD811AN). Formaldehyde dehydrogenase was immobilized onto a piezoelectic ceramic crystal, together with the cofactors, reduced glutathione and nicotinamide adenine dinucleotide. The effect of flow rate on the sensitivity was determined by varing the flow rate of carrier gas from 24.7mL/min to 111.7mL/min through detector cell. The results indicated that as the flow rate was increased, the recovery rate was increased. And a significant increase in the sensitivity was observed in enhanced flow rate of carrier gas. Frequency difference(ΔF) of immobilized PZT piezoelectic disk increased proportionally to the concentration gas and reproduced to repeated exposures of formaldehyde gas(28ppm, Δ68Hz).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.269-272
• /
• 2003

Nowadays, the study on the ceramic components and modules using LTCC is being performed and on the passives included in modules is being done also. But the characteristics of passives changes in ceramic module due to the coupling between patterns, so each block in module must be analyzed in the state of module including coupling factors. In our research each block of VCO, resonator part, oscillator part, output part is measured and analyzed and that allows the prediction of behavior of VCO.

• Journal of Sensor Science and Technology
• /
• v.19 no.2
• /
• pp.149-154
• /
• 2010

Top of the alumina body which is made according to plan has been printed using a screen printer equipment in order to print an electrode pattern. The electrode is connected with the quartz crystal oscillator of the piezoelectricity method which has a piezoelectric characteristic. The pressure contact department has been experimented using three type of the teflon. The teflon is good for pressure delivery vector but it is bad restitution. So we devised the structure which inserts the metal in the teflon. Bottom of the module is connected with the signal processing department which is planned in advance and then has investigated to characteristic. Therefore we have got the best output-voltage and frequency characteristic follows in the pressure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.109-114
• /
• 2002

Aging stabilities of the operating frequency of piezoelectric devices such as filter, oscillator and discriminator are very important. In this study it was studied aging stabilities of the length-extensional vibration mode of Pb(Zr$\_$y/Ti$\_$1-y/)O$_3$+x[wt%]Cr$_2$O$_3$ ceramics. PZT ceramics in Morphotropic phase boundary have higher aging rates of k$\_$31/ and resonant frequency than those in tetragonal phase or rhombohedral phase. Thermal aging moves the composition with maximum aging rate to Zr-rich side in Cr not added PZT system. Aging rate of resonant frequency of the ceramics with x=0.1, y=0.53 and x=0.3, y=0.53 increased by thermal aging.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.1
• /
• pp.70-77
• /
• 1999

A miniaturized voltage controlled oscillator using multi-layer ceramic technology at PCS frequency band is designed and fabricated. To improve the phase noise characteristics and to reduce the size, the strip line which is embedded in a high performance multi-layer ceramic substrate is used as an inductor of VCO. And the fabricated VCO is very small size ($6mm\times6mm\times2mm$). At the bias condition of 3.3 V and 9mA, the output power and phase noise in the operating frequency range of 1,720~1,780 MHz are -3.7 dBm and -95 dBc/Hz at 10 KHz offset from the carrier, respectively. The phase noise and size are better than the conventional VCO using glass epoxy substrate.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.6
• /
• pp.202-207
• /
• 1997

Design and fabrication issues for an L-band GaAs Monolithic Microwave Integrated Circuit(MMIC) Voltage Controlled Oscillator(VCO) as a component of Personal Communications Systems(PCS) Radio Frequency(RF) transceiver are discussed. An ion-implanted GaAs MESFET tailored toward low current and low noise with 0.5mm gate length and 300mm gate width has been used as an active device, while an FET with the drain shorted to the source has been used as the voltage variable capacitor. The principal design was based on a self-biased FET with capacitive feedback. A tuning range of 140MHz and 58MHz has been obtained by 3V change for a 600mm and a 300mm devices, respectively. The oscillator output power was 6.5dBm wth 14mA DC current supply at 3.6V. The phase noise without any buffer or PLL was 93dB/1Hz at 100KHz offset. Harmonic balance analysis was used for the non-linear simulation after a linear simulation. All layout induced parasitics were incorporated into the simulation with EEFET2 non-linear FET model. The fabricated circuits were measured using a coplanar-type probe for bare chips and test jigs with ceramic packages.