• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제16권12호
• /
• pp.4024-4041
• /
• 2022

Robust reversible watermarking has attracted widespread attention in the field of information hiding in recent years. It should not only have robustness against attacks in transmission but also meet the reversibility of distortion-free transmission. According to our best knowledge, the most recent robust reversible watermarking methods adopt a single image as the carrier, which might lead to low efficiency in terms of carrier utilization. To address the issue, a novel dual-image robust reversible watermarking framework is proposed in this paper to effectively utilize the correlation between both carriers (namely dual images) and thus improve the efficiency of carrier utilization. In the dual-image robust reversible watermarking framework, a two-layer robust watermarking mechanism is designed to further improve the algorithm performances, i.e., embedding capacity and robustness. In addition, an optimization model is built to determine the parameters. Finally, the proposed framework is applied in different domains (namely domain-independent), i.e., Slantlet Transform and Singular Value Decomposition domain, and Zernike moments, respectively to demonstrate its effectiveness and generality. Experimental results demonstrate the superiority of the proposed dual-image robust reversible watermarking framework.

• 한국세라믹학회지
• /
• 제37권5호
• /
• pp.479-490
• /
• 2000

The microstructure of Ni-YSZ composite as an anode of SOFC was investigated as a function of Ni content(10-70 vol%) in order to examine the correlation between microstructural-and electrical property. Image analysis based on quantitative microscopy theory was performed to quantify the microstructural property. We could get the informations about the size and distribution, contiguity and interfacial area of each phase or between the phases from the image analysis. According to the image analysis, contiguity between the same phae was mainly dependent on the amount of the phase while the contiguity between different phases was additionally influenced by the microstructural changes, especailly by the coarsening of the Ni phase. The whole length of pores perimeter was increased as Ni content increased, which indicated the overall microstructural evolution was mostly related with the coarsening of Ni phase. Ni-Ni interfacial area was also gradually increased as Ni content increased but controlled by pore phase at low Ni content region and by YSZ phase at intermediate Ni content region. These quantified microstructural properties were used to characterize the electrical properties of Ni-YSZ composite.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제17권2호
• /
• pp.471-485
• /
• 2023

As data sharing increases explosively, such information encoded in QR code is completely public as private messages are not securely protected. This paper proposes a new 'PROMISE' framework for hiding information based on the QR code projection matrix by using image segmentation without modifying the essential QR code characteristics. Projection matrix mapping, matrix scrambling, fusion image segmentation and steganography with SEL(secret embedding logic) are part of the PROMISE framework. The QR code could be mapped to determine the segmentation site of the fusion image as a binary information matrix. To further protect the site information, matrix scrambling could be adopted after the mapping phase. Image segmentation is then performed on the fusion image and the SEL module is applied to embed the secret message into the fusion image. Matrix transformation and SEL parameters should be uploaded to the server as the secret key for authorized users to decode the private message. And it was possible to further obtain the private message hidden by the framework we proposed. Experimental findings show that when compared to some traditional information hiding methods, better anti-detection performance, greater secret key space and lower complexity could be obtained in our work.

• 한국컴퓨터정보학회논문지
• /
• 제20권10호
• /
• pp.23-29
• /
• 2015

In this paper, we suggest a method of detecting defects by applying Hough transform and least squares on ceramic images obtained from non-destructive testing. In the ceramic images obtained from non-destructive testing, the background area, where the defect does not exist, commonly show gradual change of luminosity in vertical direction. In order to extract the background area which is going to be used in the detection of defects, Hough transform is performed to rotate the ceramic image in a way that the direction of overall luminosity change lies in the vertical direction as much as possible. Least squares are then applied on the rotated image to approximate the contrast value of the background area. The extracted background area is used for extracting defects from the ceramic images. In this paper we applied this method on ceramic images acquired from non-destructive testing. It was confirmed that extracted background area could be effectively applied for searching the section where the defect exists and detecting the defect.

• 한국전자통신학회논문지
• /
• 제5권3호
• /
• pp.321-326
• /
• 2010

본 논문에서는 세라믹을 비파괴 검사를 통하여 얻어진 영상에서, 조직의 이상이나 결함의 정도를 자동으로 확인하는 방법을 제안한다. 비파괴 검사를 통하여 얻어진 영상에서 소벨 마스크를 적용하여 윤곽선을 추출하고, 추출된 윤곽선의 방향 정보를 $9{\times}9$ 마스크에 적용하여 영역을 분류한다. 그리고 분류된 각 영역을 히스토그램 스트레칭을 적용하여 영상을 보정하고, 4-방향 윤곽선 알고리즘을 적용하여 객체를 추출한다. 그리고 추출된 객체의 영역에 대해 형태학적 정보를 이용하여 잡음을 제거한 후, 손상된 영역을 추출한다. 본 논문에서 제안한 방법을 비파괴검사를 통하여 얻어진 영상을 대상으로 실험한 결과, 손상된 영역이 정확히 검출되는 것을 확인하였다.

• 한국세라믹학회지
• /
• 제43권4호
• /
• pp.259-263
• /
• 2006

The applicability of UPT (Ultrasound Pulse Thermography) for real-time defect detection of the ceramic heating plate is described. The ceramic heating plate with superior insulation and high radiation is used to control the water temperature in underwater environment. The underwater temperature control system can be damaged owing to the short circuit, which resulted from the defect of the ceramic heating plate. A high power ultrasonic energy with pulse duration of 280 ms was injected into the ceramic heating plate in the vertical direction. The ultrasound excited vibration energy sent into the component propagate inside the sample until they were converted to the heat in the vicinity of the defect. Therefore, an injection of the ultrasound pulse wave which results in heat generation, turns the defect into a local thermal wave transmitter. Its local emission is monitored and recorded via the thermal infrared camera at the surface which is processed by image recording system. Measurements were Performed on 4 kinds of samples, composed of 3 intact plates and the defect plate. The observed thermal image revealed two area of crack in the defective ceramic heating plate.

• 한국재료학회지
• /
• 제27권11호
• /
• pp.583-589
• /
• 2017

Ceramic ink-jet printing has become a widespread technology in ceramic tile and ceramicware industries, due to its capability of manufacturing products on demand with various designs. Generally, thermally stable ceramic inks of digital primary colors(cyan, magenta, yellow, black) are required for ink-jet printing of full color image on ceramic tile. Here, we synthesized an aqueous glass-ceramic ink, which is free of Volatile organic compound(VOC) evolution, and investigated its inkjet printability. $CoAl_2O_4$ inorganic pigment and glass frit were dispersed in aqueous solution, and rheological behavior was optimized. The formulated glass-ceramic ink was suitably jetted as single sphere-shaped droplets without satellite drops. After ink-jet printing and firing processes, the printed glass-ceramic ink pattern on glazed ceramic tile was stably maintained without ink spreading phenomena and showed an improved scratch resistance.

• 한국세라믹학회지
• /
• 제56권6호
• /
• pp.596-600
• /
• 2019

Artificial intelligence with a sufficient amount of realistic big data in certain applications has been demonstrated to play an important role in designing new materials or in manufacturing high-quality products. To reduce cracks in ceramic products using machine learning, it is desirable to utilize big data in recently developed data-driven optimization schemes. However, there is insufficient big data for ceramic processes. Therefore, we developed a numerical algorithm to make "virtual" manufacturing data sets using indirect methods such as computer simulations and image processing. In this study, a numerical algorithm based on the random walk was demonstrated to generate images of cracks by adjusting the conditions of the random walk process such as the number of steps, changes in direction, and the number of cracks.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.83.2-83.2
• /
• 2011

In this study, we fabricated tubular ceramic support for segmented-in-series solid oxide fuel cell (SOFC) by using MAO(MgAl-stabilized ) as main material and activated carbon as pore former. Thermal expansion properties of ceramic support with different amounts of activated carbon were analyzed by using dilatometer to decide a suitable sintering temperature. The tubular ceramic supports with different amounts of activated carbon (15, 20, 30wt.%) were fabricated by the extrusion technique. After sintering at $1400^{\circ}C$ for 2h, cross section and surface morphology of tubular ceramic support were analyzed by using SEM image. Also, the porosity, mechanical property, gas permeability of tubular ceramic supports was measured. Based on these results, we established the suitable fabrication technique of tubular ceramic support for segmented-in-series SOFC.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.787-790
• /
• 2006

This paper analyzes the principle and feature of the piezoelectric ceramic print head for the image printing of industrial inkjet plotter, and apply the Drop-on-Demand method that can adjust an ink drop size in accordance with the certain time adjustment. In order to do this study, drive frequency is selected at maximum 8.3[kHz] which can be operated within resonance frequency range of the piezoelectric ceramic. Drop controlling was realized according to pulse waveform the drive voltage, and grey-scale and satellite diminution method were applied for printing of high resolution image. A feasibility study of the result will be demonstrated by constructing the experiment equipment.