• Journal of the Korean Ceramic Society
• /
• v.45 no.11
• /
• pp.707-712
• /
• 2008

Plasma resistant nanocrystalline $Y_2O_3$ films were deposited on alumina substrates through the electron-beam PVD technique. Increasing substrate temperature to $600^{\circ}C$ resulted in the textured microstructures with significantly enhanced adhesion force of the coating to the substrate. During the exposure to fluorine plasma, erosion rate of the coated specimen was higher than that of a sintered yttria specimen, but significantly lower than that of a single crystalline alumina. Considering the adhesion and erosion behaviors observed in the coated specimen prepared at $600^{\circ}C$, the deposition technique appears effective in reducing contamination particles generated from the ceramic parts in the plasma environment.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.4
• /
• pp.168-172
• /
• 2010

Superhydrophilic thin film consisted of positively charged poly (allylamine hydrochloride) (PAH) and negatively charged poly (acrylic acid) (PAA) was fabricated by a layer-by-layer (LBL) self-assembly. Glutaraldehyde (GA) was used in order to increase an adhesion hardness by amine-aldehyde reaction. The surface morphology, thickness, transmittance, water contact angle and adhesion hardness of PAH/PAA thin film with or without GA were measured. The adhesion hardness of PAH/PAA thin film with GA deposition increased over 2 times although the film thickness of PAH/GA/PAA decreased than that of PAH/PAA thin film. The increase of adhesion hardness by amine-aldehyde reaction between PAH and GA was measured by fourier transform infrared (FT-IR) spectroscopy. Fabricated PAH/PAA and PAH/GA/PAA thin films showed water contact angel under $5^{\circ}$ and high transmittance over 91.3% at 550 nm.

• Journal of the Korean Ceramic Society
• /
• v.32 no.10
• /
• pp.1147-1161
• /
• 1995

When ceramic membrance was made from metal salt solution in place of metal akoxide solution, crack free and good adhesion to supporter was optimized for sol stability and good adhesion force. A starting sol was prepared from aluminum oxychloride aqueous solutjion in order to inhibit the grain growthof Al2O3 during heat treatment. The crack free dip coating can't be achieved in 1mol/ι zirconium oxychloride solution because of the high viscosity which interferes with the hydration copolymerization between Al3+ ion and Zr4+ ion. Thus Al2O3-ZrO2 sol stability and viscosity for dip coating was effective when 0.01 mol/ι zirconium oxychloride was added. The minimizing of crack and achieving better adhesion to the supporter wa obtained by microwave drying, surfactant addition and ultrasonic dip coating in wet atmosphere. The result seems to minimize the capillary force and improve the adhesive ability to supporter during the process. Where the average pore size of Al2O3-ZrO2 ultrafilter ceramic membrane measured 17 Å by the BET method and observed γ-Al2O3 phase with tetragonal zirconia after firing at 700℃.

• Journal of Technologic Dentistry
• /
• v.29 no.2
• /
• pp.213-223
• /
• 2007

The success of a porcelain fused to metal (PFM) restoration depends upon the quality of the porcelain-metal bond. The adhesion between metal substructure and dental porcelain is related to the diffusion of oxygen to the reaction layer formed on cast-metal surface during firing. The purposed of this investigation was to study the effects of gold based bonding agent on Ni-Cr alloy-ceramic adhesion between porcelain matrix, gold based bonding agent and metal substructure interface. gold based bonding agent have been applied as an intermediate layer between a metal substructure and a ceramic coating. gold based bonding agent(Aurofilm NP, Metalor, Swiss) was applied on Ni-Cr alloy surface by four method. Surfaces only air abraded with 110${\beta}\neq$ Al2O3 particles were used as control. metal ceramic adhesion was evaluated by a biaxial flexure test(N=5) and volume fraction of adherent porcelain was determined by SEM/EDS analysis. Result of this study suggest that the layering sequence of gold based bonding agent is very important and can improve porcelain adherence to PFM.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.441-446
• /
• 2009

Dense crack-free yttria film with 10 $\mu m$ thickness was prepared on aluminum by aerosol deposition. X-ray diffraction pattern on the film showed that it contained the same crystalline phase as the raw powder. Transmission electron microscopy revealed a nanostructured yttria film with grains smaller than 100 nm. Tensile adhesion strength between the film and aluminum substrate was 57.8 $\pm$ 6.3MPa. According to the etching test with $CF_4-O_2$ plasma, the etching rate of the yttria film was 1/100 that of quartz, 1/10 that of sintered alumina and comparable to that of sintered yttria.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.121-121
• /
• 2000

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.208-208
• /
• 2008

Micro patterning of conductor line/space on LTCC green sheet in the LTCC module is an important process for miniaturization in 3D integrated circuits. This work presented the effect of inorganic binders on the microstructure, adhesion, electrical resistivity, shrinkage and line/space resolution, which is a part of study in photoimageable conductor paste. The photoimageable conductor paste contains silver powder, polymer binder, monomer, photo-initiator, UV absorber, and solvent. The inorganic binders were furnished with varied weight percentage of anorthite, diopside and MLS-62 glass frits from 0% to 7%. The Line/space sizes thus obtained was under 25 micron.

• Journal of the Korean Ceramic Society
• /
• v.32 no.4
• /
• pp.405-412
• /
• 1995

In order to estimate the wettability of the borosilicate glasses with different composition on the noble metals of gold and silver, the measurements of the contact angle between the solid and the liquid were made at various temperatures and holding times using the sessil-drop method. The wetting behavior and the adhesion of the phases were strongly influenced by the thermal or the physical characteristics of the materials. The dependence of wetting angle ($\theta$) on the holding time (t) could be represented by the relation of $\theta$=a.tb, whereby the wettability of the systems was quantitatively compared. Also with increasing content of borosilicate glass in the glass-gold matrix composite, the tensile strength was decreased whereas the elastic modulus was increased.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.3
• /
• pp.186-194
• /
• 1996

In this study, ceramic film was coated by a sol-gel process for increasing the adhesion strength between the substrate and copper layer. TEOS and ATSB were used as starting solution of metallic alkoxide. As a result, amorphous-like diffraction pattern after heat treatment at $1200^{\circ}C$ was obtained using X-ray diffractometer. The more contants of $Al_2O_3$ gave rise to the futher advanced cracks. A maximum adhesion strength of 250gf was measured under the condition of 30 Wt.% $Al_2O_3$, which is 5 times greater than that of uncoated one of the ceramic film.

• The Journal of the Korean dental association
• /
• v.50 no.7
• /
• pp.377-383
• /
• 2012

Recently, ceramic materials have become a popular choice for dentists performing esthetic indirect restorations. The longevity and success of ceramic dental restorations depends on the adhesive procedures of resin cements. However, dental ceramics can be classified in various ways, depending on the compositions. Also, the applications for resin cement require multiple clinical steps. Therefore, understanding the different ceramic substrates involved in each procedure, as well as the proper adhesive steps for the resin cements is important to us for long-term clinical success.