• Journal of Veterinary Science
• /
• v.22 no.6
• /
• pp.74.1-74.13
• /
• 2021

Tissue engineering has been extensively investigated and proffered to be a potential platform for novel tissue regeneration. The utilization of mesenchymal stem cells (MSCs) from various sources has been widely explored and compared. In this regard, MSCs derived from bone marrow have been proposed and described as a promising cell resource due to their high yield of isolated cells with colony-forming potential, self-renewal capacity, MSC surface marker expression, and multi-lineage differentiation capacities in vitro. However, there is evidence for bone marrow MSCs (BM-MSCs) both in vitro and in vivo from different species presenting identical and distinct potential stemness characteristics. In this review, the fundamental knowledge of the growth kinetics and stemness properties of BM-MSCs in different animal species and humans are compared and summarized. Finally, to provide a full perspective, this review will procure results of current information studies focusing on the use of BM-MSCs in clinical practice.

• Corrosion Science and Technology
• /
• v.3 no.2
• /
• pp.54-58
• /
• 2004

Effects of texture on the electrochemical behaviors of single grains in polycrystalline zinc were investigated using a capillary-based micro-droplet cell. Pontiodynamic sweeps and capacity measurements were carried out in pH 9 borate buffer solution. The cyclic voltammograms and the capacity measurements on single grains with different crystallographic orientations in polycrystalline Zn showed a strong dependence of oxide growth on crystallographic grain orientation. The total charge consumed for oxide formation and the inverse capacity increased with an increase of surface packing density of grain. suggesting the oxide formation was greater on grains with higher surface packing density.

• Korean journal of food and cookery science
• /
• v.22 no.1 s.91
• /
• pp.30-36
• /
• 2006

Tofu samples with added herbs (green tea, rosemary, lavender and thyme) were prepared. The yield of the herb tofus was higher than that of the control tofu. The L value of the control tofu was higher than that of the herb tofus, whereas the b values were lower. The herb tofus had generally lower pH than the control tofu. Especially, lavender tofu showed the lowest pH. Under SEM examination, the control tofu showed a rough folding surface, whereas the green tea and lavender tofus had small air cell size and smooth surface. Most textural characteristics did not show significant difference among the tofu groups. However, chewiness and hardness of the thyme tofu were the lowest. In the sensory evaluation, the herb tofus had low scores in air cell size and a beany smell, but high scores in herb smell and hardness.

• Proceedings of the Korea Society of Poultry Science Conference
• /
• 2001.11a
• /
• pp.69-70
• /
• 2001

Lectins have great potential as to determine the alternation of the distribution of cell surface carbohydrates during cellular development and differentiation. Here, we investigated the presence and distribution of cell surface carbohydrates on chicken primordial germ cells (PGCs) during the migration and gonadal stages using a variety of lectins. A total of six FITC-labelled lectins from several specificity classes were used: ConA (glucose/mannose), WGA (N-acetylglucosamine), STA (N-acetylglucosamine), DBA (N-acetylgalactosamine/galactose), UEA-I (fucose) and PHA-E (oilgosaccharide). As a results, PGC-specific binding was observed in STA. PGCs of migration stage (2.5- and 5.5-day embyos) were STA-positive whereas PGCs of 10-day embryonic gonad were not. The results suggest that N-acetylglucosamine residuse are present specifically in migrating chicken PGCs and changes during development.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.221-221
• /
• 2014

The current energy crisis in many countries has led to the search of an efficient renewable energy source. Among those the solar energy is the most abundant and easily available. However harvesting the solar energy requires a much efficient device. Lot of research has been done in this regard and so far the efficiency of traditional solar cell stands around ~50% and for PET films it is much lesser. The potential application of PET films in the solar cells can be very promising provided the fact that the PET film is lighter and logistically more viable. There is a lot of work that is being done to increase the efficiency of PET based solar cells. The base electrode plays a vital role in increasing the efficiency of the cell.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.4
• /
• pp.191-195
• /
• 2004

Gallium or sulphur additions in $CuInSe_2$ were prepared using RF magnetron sputtering and pulsed laser deposition respectively. All of the observed thin films shows a chalcopyrite structure with the S and Ga addition increases the favourable (112) peak. The optical absorption coefficients were slightly decreased. The energy band gap of films could be shifted from 1.04 to 1.68 eV by adjusting the mole ratio of S/(S+Se) and Ga/(In+Ga). It is possible to obtain the optimum energy band gap by adding S or Ga solute at a certain ratio in favour of Se and In respectively. It is also necessary to control the ratio of Ga and S additions and to retain a certain portion of In and Se to provide better properties of thin films.

• Current Photovoltaic Research
• /
• v.6 no.4
• /
• pp.91-93
• /
• 2018

Polythiophene-$TiO_2$ composite was synthesized with different molar ratios of thiophene and titaniumisopropoxide ($Ti(OPr)_4$) for flexible solar cell application as a flexible electrode or an active material. The $Ti(OPr)_4$ was stabilized by thiophene. The thiophene was polymerized by ferric chloride catalyst. The synthesized polythiophene exhibited strong UV-visible absorption in the range of the wavelength shorter than 500 nm. Field emission scanning electron microscope (FESEM) image of low concentration of $TiO_2$ film showed smooth surface. However, FESEM image of high concentration of $TiO_2$ film exhibited relatively rough surface. Polythiophene concentration dependent strong photoluminescence quenching of surfrhodamine-B was observed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.347.1-347.1
• /
• 2016

Screen printing is commonly used to form the electrode for crystalline silicon solar cells. However, it has caused high resistance and low aspect ratio, resulting in decrease of conversion efficiency. Accordingly, Ni/Cu/Ag plating method could be applied for crystalline silicon solar cells to reduce contact resistance. For Ni/Cu/Ag plating, laser ablation process is required to remove anti-reflection layers prior to the plating process, but laser ablation results in surface damage and then decrease of open-circuit voltage and cell efficiency. Another issue with plating process is ghost plating. Ghost plating occurred in the non-metallized region, resulting from pin-hole in anti-reflection layer. In this paper, we investigated the effect of Ni/Cu/Ag plating on the electrical properties, compared to screen printing method. In addition, phosphoric acid layer was spin-coated prior to laser ablation to minimize emitter damage by the laser. Phosphorous elements in phosphoric acid generated selective emitter throughout emitter layer during laser process. Then, KOH treatment was applied to remove surface damage by laser. At this step, amorphous silicon formed by laser ablation was recrystallized during firing process and remaining of amorphous silicon was removed by KOH treatment. As a result, electrical properties as Jsc, FF and efficiency were improved, but Voc was lower than screen printed solar cells because Voc was decreased due to surface damage by laser process. Accordingly, we expect that efficiency of solar cells could be improved by optimization of the process to remove surface damage.

• Clean Technology
• /
• v.18 no.4
• /
• pp.446-450
• /
• 2012

Strong alkaline electrolyzed water which is produced in cathode by electrolyzing the solution where electrolytes (NaCl, $K_2CO_3$ etc.) are added in diaphragm electrolytic cell, is eco-friendly and has cleaning effects. So, it is viewed as a substitution of chemical cleaner. In addition, strong alkaline electrolyzed water is being used by some Japanese automobile and precision parts manufacturing industries. When strong alkaline electrolyzed water is produced by using diaphragm electrolytic cell, it is necessarily produced at the anode side. Since strong acidic electrolyzed water produced is discarded when its utilization cannot be found, production efficiency of electrolyzed water is consequently decreased. Also, there is a weakness electrolytic efficiency is decreasing due to the pollution of diaphragm. In order to overcome this, non-diaphragm all-in-one electrolytic cell integrated with electrode reaction chamber and dilution chamber was applied. Strong alkaline electrolyzed water was produced for different composition of electrolytes, and their properties and characteristics were identified. In comparing the properties between strong alkaline electrolyzed water produced in diaphragm electrolytic cell and that produced in all-in-one electrolytic cell, the differences in ORP and chlorine concentration were found. In emulsification test to confirm surface-active capability, similar results were obtained and strong alkaline electrolyzed water produced in non-diaphragm all-in-one electrolytic cell was identified to be useable as a cleaner like strong alkaline electrolyzed water produced in diaphragm electrolytic cell. Strong alkaline electrolyzed water produced in non-diaphragm all-in-one electrolytic cell is thought to have sterilizing power because it has active chlorine which is different from strong alkaline electrolyzed water produced in diaphragm electrolytic cell.

• Journal of Periodontal and Implant Science
• /
• v.44 no.5
• /
• pp.242-250
• /
• 2014

Purpose: This study aimed to evaluate the effects of fibronectin and oxysterol immobilized on machined-surface dental implants for the enhancement of cell attachment and osteogenic differentiation, on peri-implant bone healing in the early healing phase using an experimental model in dogs. Methods: Five types of dental implants were installed at a healed alveolar ridge in five dogs: a machined-surface implant (MI), apatite-coated MI (AMI), fibronectin-loaded AMI (FAMI), oxysterol-loaded AMI (OAMI), and sand-blasted, large-grit, acid-etched surface implant (SLAI). A randomly selected unilateral ridge was observed for 2 weeks, and the contralateral ridge for a 4-week period. Histologic and histometric analyses were performed for the bone-to-implant contact proportion (BIC) and bone density around the dental implant surface. Results: Different bone healing patterns were observed according to the type of implant surface 2 weeks after installation; newly formed bone continuously lined the entire surfaces in specimens of the FAMI and SLAI groups, whereas bony trabecula from adjacent bone tissue appeared with minimal new bone lining onto the surface in the MI, AMI, and OAMI groups. Histometric results revealed a significant reduction in the BIC in MI, AMI, and OAMI compared to SLAI, but FAMI demonstrated a comparable BIC with SLAI. Although both the BIC and bone density increased from a 2- to 4-week healing period, bone density showed no significant difference among any of the experimental and control groups. Conclusions: A fibronectin-coated implant surface designed for cell adhesion could increase contact osteogenesis in the early bone healing phase, but an oxysterol-coated implant surface designed for osteoinductivity could not modify early bone healing around implants in normal bone physiology.