• 한국재료학회지
• /
• 제32권11호
• /
• pp.481-488
• /
• 2022

The Cu₂ZnSn(S_xSe_1-x)₄ (CZTSSe) absorbers are promising thin film solar cells (TFSCs) materials, to replace existing Cu(In,Ga)Se₂ (CIGS) and CdTe photovoltaic technology. However, the best reported efficiency for a CZTSSe device, of 13.6 %, is still too low for commercial use. Recently, partially replacing the Zn²⁺ element with a Cd²⁺element has attracting attention as one of the promising strategies for improving the photovoltaic characteristics of the CZTSSe TFSCs. Cd²⁺ elements are known to improve the grain size of the CZTSSe absorber thin films and improve optoelectronic properties by suppressing potential defects, causing short-circuit current (J_sc) loss. In this study, the structural, compositional, and morphological characteristics of CZTSSe and CZCTSSe thin films were investigated using X-ray diffraction (XRD), X-ray fluorescence spectrometer (XRF), and Field-emission scanning electron microscopy (FE-SEM), respectively. The FE-SEM images revealed that the grain size improved with increasing Cd²⁺ alloying in the CZTSSe thin films. Moreover, there was a slight decrease in small grain distribution as well as voids near the CZTSSe/Mo interface after Cd²⁺ alloying. The solar cells prepared using the most promising CZTSSe absorber thin films with Cd²⁺ alloying (8 min. 30 sec.) exhibited a power conversion efficiency (PCE) of 9.33 %, J_sc of 34.0 mA/cm², and fill factor (FF) of 62.7 %, respectively.

• 한국재료학회지
• /
• 제11권12호
• /
• pp.1020-1027
• /
• 2001

Powder type Ag system insert metals were manufactured by mechanical alloying method. Alloying method was the ball milling process using zirconia ball media, and all alloying variables were constant except the milling time. The milling times were selected 24, 48 and 72 hours. The insert metals made by milling method were observed using scanning electron microscope and x-ray analyses. And also, the evaluation of wettability and microstructures of the insert metals were conducted to investigate the characteristics of the brazed joint. The wettability of the insert metals made by milling of 48 hours, was the best condition. And the insert metals contained Cd shows good wettability, however, there was the oxides residue on the brazing test specimen. The microstructures of the manufactured and the commercial insert metals were almost same displaying the Cu- rich proeutectic and Ag-rich eutectic. Further, there were some porosities. The 48 hours alloyed insert metal was exhibited the most sound brazed joint without containing porosity due to the superior wettability and good alloying condition.

• 대한화학회지
• /
• 제61권4호
• /
• pp.185-190
• /
• 2017

One-dimensional CdTe nanorods (NRs) are obtained by the reaction of various Cd precursors with single crystalline Te nanorod templates, which are pre-synthesized from Te precursors by a simple and reproducible solvothermal method. Throughout the process, the diffraction intensity of different crystal facets of single crystalline Te NRs varied with reaction times. Finally, by alloying Cd ions along the axial direction of Te NRs, polycrystalline cubic phase CdTe NRs with diameters of 80-150 nm and length up to $1.2-2.4{\mu}m$ are obtained. The nucleation and growth processes of Te and CdTe NRs are discussed in details, and their properties are characterized by XRD, SEM, TEM, Raman scattering, and UV-vis absorption spectra. It was found that the key elements of synthesizing CdTe NRs such as reaction temperatures and Cd sources will strongly influence the final shape of CdTe NRs.

• Transactions on Electrical and Electronic Materials
• /
• 제12권5호
• /
• pp.218-221
• /
• 2011

We modified the optical properties of the $CuInS_2$ nanocrystal (NC) by alloying. Nanocrystals (NCs) with alloyed cores were synthesized by refluxing the as-synthesized $CuInS_2$ NCs with a mixture of cadmium acetate, zinc acetate and palmitic acid. The shift in emission wavelength of the NCs after shell layer formation was minimized by alloying. The photoluminescence (PL) spectra showed significant reduction of emission intensity. A detailed study on the emission process of NCs implies that the formation of shell layers with small lattice mismatch minimized the mismatch strain generated from the shell layers in contrast to core alloyed NCs. In particular, time-resolved PL spectra of the NCs showed a significant increase in the lifetime of excited carriers by modifying the band alignment of the NCs by modifying the shell composition.

• 소성∙가공
• /
• 제28권1호
• /
• pp.34-42
• /
• 2019

In this study, various alloying elements (Cr, Sr, Ca, Cd) were added to improve the mechanical properties of ADC12 fabricated by a die casting process. The effect of alloying elements on the microstructure and mechanical properties were investigated. The phase analysis results of the modified ADC12 alloy with conventional ADC12 alloy, showed the similar characteristics of Al matrix, Si phase, $CuAl_2$ phase and the Fe intermetallic phase. As a result of the microstructure observation, the secondary dendrite arm spacing (SDAS) was shown to have decreased after the addition of the alloying elements. The eutectic Si phase, which existed as flake form in the conventional ADC12 alloy, was modified finely as a fiber form in the modified ADC12 alloy. It was observed that the $CuAl_2$ phase as the strengthening phase was relatively finely distributed in the modified ADC12 alloy. The Fe intermetallic appeared as a Chinese script shaped $Al_6$ (Mn,Fe) which is detrimental to mechanical properties in conventional ADC12 alloy. On the other hand, in the modified ADC12 alloy, polyhedral ${\alpha}-Al_{15}Si_2$ $(Fe,Mn,Cr)_3$ was observed. The tensile properties were improved in the modified ADC12 alloy. The yield strength and tensile strength increased by 12.4% and 10.0%, respectively, in the modified ADC12 alloy, and the elongation was also seen to have been increased. As a result of the pin on disk wear test, the wear resistance properties were also improved by up to about 7% in the modified ADC12 alloy. It is noted that the wear deformation microstructures were also observed, and it was found that the fine eutectic Si and strengthening phases greatly improved abrasion resistance.

• 한국재료학회지
• /
• 제17권12호
• /
• pp.654-659
• /
• 2007

Austenite precipitation behavior was studied with solidification rates and alloying contents, N and Cr, in duplex stainless steels by directional solidification. Directional solidification experiments were carried out with solidification rates, $1{\sim}100mm/s$, and N and Cr contents, $0{\sim}0.27wt.%,\;25{\sim}28wt.%$ respectively, in a duplex stainless steel, CD4MCU. As the solidification rate increases, the dendrite spacing reduced and the austenite phase in the ferrite matrix became finer. The volume fraction of austenite phase increased and its shape went to be round with increasing nitrogen contents in duplex stainless alloys. The Cr alloying element, even though it is a ferrite former, showed to enhance the nitrogen solubility in the alloy and caused the austenite round and finer. Also, Cr was supposed to decrease the austenite volume fraction, but it increased the austenite slightly due to increasing nitrogen solubility during solidification.

• 한국산학기술학회논문지
• /
• 제9권2호
• /
• pp.298-302
• /
• 2008

초경합금입자와 탄소강사이의 브레이징 접합부 특성을 평가하였다 선택된 두 종류의 삽입금속은 기계적 합금 공정으로 만들어졌다. 한 가지는 Cu, Zn, Ag (MIM-1) 그리고 다른 한 가지는 Cu, Zn, Ag과 Cd(MIM-2)로 구성하였다. 삽입금속들의 화학조성은 AWS BAg-20계와 BAg-2a계의 성분과 유사하였다. 그리고 상용삽입금속들(CIM-1, CIM-2) 역시 비교 평가하였다. 삽입금속들의 특성은 젖음성 시험, 전단강도 시험, 그리고 미세조직 관찰로서 나타내었다. 젖음성 시험에서 MIM-1과 CIM-1 삽입금속의 젖음각이 MIM-2와 CIM-2보다 크게 나타났고, MIM-1의 젖음각이 CIM-1보다 더 큰 값을 나타났지만 모든 경우 젖음각이 $25^{\circ}$보다 작았다. 삽입금속, MIM-1이 가장 높은 전단강도를 나타냈고, 그 값은 $2.29{\times}10^2MPa$로 측정되었다. 이 값은 상용 삽입금속의 값과 같거나 높은 것으로 나타났다. 삽입금속의 미세조직은 Cu-rich 초정영역과 Ag-rich 공정영역으로 구성되었다. MIM-1계로 만들어진 초경합금과 탄소강의 접합부는 일부 접합부 계면에 기공을 포함하지만 초정을 기지로 하는 안정적인 미세조직을 나타냈다.