• Bulletin of the Korean Chemical Society
• /
• v.31 no.9
• /
• pp.2649-2655
• /
• 2010

$PKC{\delta}$-catalytic V5 Heptapeptide (FEQFLDI, FP7) interacts with heat shock protein 27 (HSP27) and inhibits HSP27-mediated resistance to cell death against various stimuli including radiation therapy. Here, we prepared radio-iodinated heptapeptide and further investigated its uptake properties in HSP27 expression cells. Peptide sequence of FP7 and a negative control peptide (WSLLEKR, QP7) was modified by substituting their C-terminus residue to tyrosine (FP6Y and QP6Y) to label radio-iodine. Iodinated peptides were confirmed by LC mass analysis with cold iodine reaction mixture. Accumulation of [$^{125}I$]iodo-FP6Y and [$^{125}I$]iodo-QP6Y in NCI-H1299 cell line, with higher level of HSP27, and NCI-H460 cell line, with lower level of HSP27, was measured by NaI(Tl) scintillation counter. The modification of substituting C-terminus residue of FP7 to tyrosine (FP6Y) did not affect its interaction with HSP27. Accumulation of [$^{125}I$]iodo-FP6Y in NCI-H1299 cells was 3 fold higher than in NCI-H460 cells. The novel radio-iodinated FP6Y would be used as a tracer for targeting HSP27 protein.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.04a
• /
• pp.99-101
• /
• 1998

1. Introduction : The conventional grafting polymerization technique requires chemically reactive groups on the surface as well as on the polymer chains. For this reason, a series of prefunctionalization steps are necessary for covalent grafting. The surface prefunctionalizational technique for grafting can be used to ionization radiation, UV, plasma, ion beam or chemical initiators. Of these techniques, radiation method is one of the useful methods because of uniform and rapid creation of active radical sites without catalytic contamination in grafted samples. If the diffusion of monomer into polymer is large enough to come to the inside of polymer substrate, a homogeneous and uniform grafting reaction can be carried out throughout the whole polymer substrate. Radiation-induced grafting method may attach specific functional moieties to a polymeric substrate, such as preirradiation and simultaneous irradiation. The former is irradiated at backbone polymer in vacuum or nitrogen gas and air, and then subsequent monomer grafting by trapped or peroxy radicals, while the latter is irradiated at backbone polymer in the presence of the monomer. Therefore, radiation-induced polymerization can be used to modification of the chemical and physical properties of the polymeric materials and has attracted considerable interest because it imparts desirable properties such as blood compatibility. membrane quality, ion excahnge, dyeability, protein adsorption, and immobilization of bioactive materials. Synthesizing biocompatible materials by radiation method such as preirradiation or simultaneous irradiation has often used $\gamma$-rays to graft hydrophilic monomers onto hydrophobic polymer substrates. In this work, in attempt to produce surfaces that show low levels of anti-fouling of bovine serum albumin(BSA) solutions, hydroxyethyl methacrylate(HEMA) was grafted polypropylene membrane surfaces by preirradiation technique. The anti-fouling effect of the polypropylene membrane after grafting was examined by permeation BSA solution.

• Journal of the Korean Chemical Society
• /
• v.24 no.2
• /
• pp.155-166
• /
• 1980

3-(N-Carbonylpyrrolidone)-propanoic acid potassium-salt and 3-(N-carbonylpyrrolidone)propenoic acid potassium-salt were synthesized by the reaction of 2-pyrrolidone potassium-salt with succinic anhydride and maleic anhydride in acetone and in acetone and in benzene. The anionic polymerization of 2-pyrrolidone with 3-(N-carbonylpyrrolidone)-propanoic acid potassium-salt or 3-(N-carbonylpyrrolidone)-propenoic acid potassium-salt as an initiator and potassium hydroxide as a catalyst was studied. It was found that 2.0 and 1.0 mole %, concentration of catalyst and initiator, and temperature of $50^{\circ}C$ was the optimum condition obtaining highest conversion and viscosity of polymer. The inherent viscosity of nylon 4 was measured to be 1.2 dl/g and 2.3 dl/g.

• Korean Journal of Microbiology
• /
• v.47 no.4
• /
• pp.302-307
• /
• 2011

Native chitin deacetylase of Aspergillus nidulans was purified to apparent homogeneity by a combination of phenyl-Sepharose and Q-Sepharose column chromatography. In order to analyze the amino acid residues involved in the enzyme activity, the enzyme was chemically modified with chemical agent, which selectively reacted with the specific amino acid residue on the protein. When the enzyme was chemically modified with diethylpyrocarbonate, which specifically reacted with histidine residues on the protein, the activity was eliminated. The chitin deacetylase, chemically modified with 100 ${\mu}M$ modifier at the residue of arginine or tyrosine, has shown to have decreased activities. It was shown that the modification at aspartic acid or glutamic acid did not affect the enzyme activity to a greater extent, which would not implicate that acid amino residues were directly involved in catalytic reaction and would affect on the global structures of the proteins. This results demonstrated that histidine and tyrosine residues of enzyme would participate in an important function of the chitin deacetylase activity.

• Clean Technology
• /
• v.16 no.2
• /
• pp.95-102
• /
• 2010

Sulfonic acid (-SO3H) functionalized mesoporous silica containing HMS, SBA 15(S15), MCM 41(M41) were synthesized by post-synthesis and co-condensation method. Their catalytic performance is tested by dehydration reaction of D-xylose to furfural. As a result, good conversion and selectivity was obtained using water as an environmentally friendly solvent. Additionally, increased amounts of sulfuric acid in catalysts resulted in improved conversion of D-xylose. All of the acid-functionalized mesoporous silica showed higher selectivity than other solid acids such as ${\gamma}-Al_{2}O_{3}$ and zeolite.

• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.28-35
• /
• 2000

In this study, we investigated the characteristics of polyurethane synthesis by simultaneously measuring resonant frequency and resonant resistance with a quartz crystal analyzer. The rapid decrease of resonant frequency was appeared because automatic catalytic reaction was caused by the polyurethane formed in initial stage of polyurethane synthesis. In prepolymer(PP) synthesis, the resonant frequency was slowly stabilized after a rapid decrease at a certain point of time. But in segmented polyurethane synthesis in which chain-extender was involved, the resonant frequency increased again after a rapid decrease at a certain point of time. It was considered that this tendency took place because the chain-extender, 1,4-butandiol, caused a soft segment to change to a hard segment. The resonant resistance was used in the analysis of mechanism. From the results, the characteristics of polyurethane synthesis could be analyzed on-line using a quartz crystal analyzer, and the synthesis mechanism could also be interpreted.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.550-554
• /
• 2008

The synthesis of dimethyl carbonate (DMC) from methanol and supercritical carbon dioxide over $K_2CO_3/ZrO_2$ catalysts have been studied. The catalysts were prepared by impregnating $ZrO_2$ with an aqueous $K_2CO_3$ solution. The optimum calcination temperature to disperse K species on the $ZrO_2$ surface was found to be 673 K. Monoclinic $ZrO_2$ was not active, as itself, for the DMC production. However, when the $K_2CO_3$ was impregnated on the $ZrO_2$, the catalytic performance was improved. Besides the catalyst, $CH_3I$ was used as a promoter. The $CH_3I$ promoter as well as the $K_2CO_3/ZrO_2$ catalyst was found to take an important role to improve the production of DMC. The optimum quantities for the catalyst and the promoter were estimated. The effect of the catalyst and the promoter for the DMC synthesis from methanol and supercritical carbon dioxide was investigated and the reaction mechanism was proposed.

• Clean Technology
• /
• v.13 no.4
• /
• pp.287-292
• /
• 2007

[ $M/Al_2O_3$ ] (M = Mn, Fe, Co, Ni, Cu) catalysts supported on commercial alumina ($Al_2O_3$) were prepared by an impregnation method, and were applied to the hydrogen production by auto-thermal reforming of ethanol. It was revealed that each catalyst retained its own metallic phase and product distribution strongly depended on the identity of active metal. Among the catalysts prepared, $Ni/Al_2O_3$ and $Co/Al_2O_3$ showed the best catalytic performance in the auto-thermal reforming of ethanol. However, the reaction mechanisms over these two catalysts were different. Ni/Al_2O_3 catalyst showed 100% ethanol conversion at $500^{\circ}C$, but it exhibited a rapid decrease in hydrogen selectivity. Although $Co/Al_2O_3$ catalyst showed an excellent performance in hydrogen selectivity, on the other hand, no significant improvement in hydrogen yield was observed due to the low ethanol conversion over the catalyst.

• Journal of Energy Engineering
• /
• v.23 no.3
• /
• pp.150-156
• /
• 2014

In this study, we implemented a research for improving performance of redox flow battery (RFB) via enhancing reaction rate of vanadium reaction ($[VO]^{2+}/[VO_2]^+$) that was a rate determining step. For doing that, porous catalyst, CMK3 was employed and its perfoamance was compared with that of Vulcan(XC-72) and commercial Pt/C (Johnson-Matthey Pt 20wt.%). Cyclic voltammetry (CV) was used for inspecting reactivity, while its structural feature was measured by TEM and BET&BJH. Also, Charge-discharge trend was evaluated by single cell tests. As result, CMK3 showed 6 times better catalytic activity and twice better reversibility than Vulcan(XC-72), while it showed larger surface area than Vulcan XR due to its porous structure. Furthermore, CMK3 indicated 85% of reactivity and reversibility of commercial Pt/C despite its Pt-less situation. In single cell tests, when RFB adopted CMK3 as catalyst for positive electrode, its charge-discharge curve result was better than that adopted commercial Pt/C.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.1
• /
• pp.20-27
• /
• 2012

The $NH_3$-SCR characteristics of $NO_X$ over a V-based catalyst are experimentally examined over a wide range of operating conditions, i.e., $170-590^{\circ}C$ and $30,000-50,000h^{-1}$, with a simulated diesel exhaust containing $NH_3$, NO, $NO_2$, $O_2$, $H_2O$, and $N_2$. The influences of the space velocity and oxygen concentration on the standard-SCR reaction are analyzed, and it is shown that the low space velocity and high oxygen concentration promote the SCR activity by ammonia. The best $deNO_X$ efficiency is obtained with a $NO_2/NO_X$ ratio of 0.5 because of an enhanced chemical activity induced by the fast-SCR reaction, while at the $NO_2/NO_X$ ratios above 0.5 the $deNO_x$ activity decreases due to the slow-SCR reaction. The oxidation of ammonia begins to take place at about $300^{\circ}C$ and the reaction products, such as $N_2$, NO, $NO_2$, $N_2O$, and $H_2O$, are produced by the undesirable oxidation reactions of ammonia, particularly at high temperatures above $450^{\circ}C$. Also, $NO_2$ decomposes to NO and $O_2$ at temperatures above $240^{\circ}C$. Therefore, $NO_2$ decomposition and ammonia oxidation reactions deteriorate significantly the SCR catalytic activity at high temperatures.