• 대한기계학회논문집A
• /
• 제23권11호
• /
• pp.2087-2095
• /
• 1999

One of the main causes of unwanted dimensional changes in precision metal mold casting parts is excessive and irregular residual stresses induced by temperature gradients and plastic deformation in the solidifying shell. Residual stresses can also cause stress cracking, and lower the fatigue life and fracture strength of the casting parts. In the present study, aluminum alloy casting system with metal mold equipped with electrical heating elements and water cooling units was designed and the casting specimens were produced to quantify the effects of different cooling conditions on the development of residual stresses. The layer removal method was used to measure the biaxial residual stresses in casting specimens produced from the experiments. The experimental results agreed with Tien-Richmond's theoretical model for thermal stress development for the solidifying metal plate.

• 대한치과의사협회지
• /
• 제10권12호
• /
• pp.809-812
• /
• 1972

This present paper is concerned with four unit fixed bridge construction by one piece casting technique in the case of missing of upper left second premolar and first molar. The authors had good clinical results with following advantages. 1. The complete bridge can be delivered to the patient for two appointments. 2. The laboratory procedures for solder joint are not necessary. 3. A one piece casting can be properly shaped without weak joints. 4. The casting can be heat-treated to insure an ideal molecular structure. 5. Porcelain veneers can be applied without weakening or melting solder joints.

• 한국주조공학회지
• /
• 제24권2호
• /
• pp.63-70
• /
• 2004

Foundry techniquews for large steel casting depends on the skills of foundrymen considerably. Especially, the problem of reducing casring surface defects is difficult to clear numerically. Statistical analysis by using wuantification theory for hot tear and sand inclusion, and multiple regression analysis for dimensional defects have been shown to be examples of solving this difficulty. Many causes of surface defects can be evaluated by these analyses. These evaluations serve as the base data of defect reduction and contribute to the constant improvement of casting quality and quality enhancement activity. The system to perform quality enhancement activity was developed and it proved very useful for transfering foundry techniques and skills from the old to young generations.

• 한국정밀공학회지
• /
• 제16권6호
• /
• pp.52-57
• /
• 1999

Funtional metal prototypes are often required in numerous industrial applications. These components are typically needed in the early stage of a project to determine form, fit and function. Recent R/P(Rapid Prototyping) part are made of soft materials such as plastics, wax, paper, these master models cannot be employed durable test in real harsh working environment. Parts by direct metal rapid tooling method, such as laser sintering, by now are hard to get net shape, pores of the green parts of powder casting method must be infiltrated to get proper strength as tool, and new type of 3D direct tooling system combining fabrication welding arc and cutting process is reported by song etc. But a system which can build directly 3D parts of high performance functional material as metal part would need long period of system development, massive investment and other serious obstacles, such as patent. In this paper, through the rapid tooling process as silicon rubber molding using R/P master model, and fabricate wax pattern in that silicon rubber mold using vacuum casting method, then we tranlsated the wax patterns to numerous metal prototypes by new investment casting process combined conventional investment casting with rapid pototyping & rapid tooling process. with this wax-injection-mold-free investment casting, we developed new investment casting process of fabricating numerous functional metal prototypes from one master model, combined 3-D CAD, R/P and conventional investment casting and tried to expect net shape measuring total dimension shrinkage from R/P part to metal part.

• 한국주조공학회지
• /
• 제14권3호
• /
• pp.248-257
• /
• 1994

Research in heat transfer and solidification commonly involves experimentation and mathematical modeling with associated numerical analysis and computation. Inverse problems in heat transfer are part of this paradigm. During the solidification of metal casting, an interfacial heat transfer resistance exists at the boundary between the casting and the mold, and this heat transfer resistance usually varies with time. In the case of the squeeze casting the contact heat transfer resistance is decreased by pressure and ideal contact is almost accomplished. In the present work, heat transfer coefficient, which is inverse value of the heat transfer resistance, was used for convenience. A numerical technique, Non-Linear Estimation has been adopted for calculation of the casting/mold interfacial heat transfer coefficient during the squeeze casting process. In this method, the measured temperature data from experiment were used. The computational results were applied to the analysis of heat transfer and solidification.

• 한국주조공학회지
• /
• 제28권3호
• /
• pp.113-118
• /
• 2008

A new approach of producing martensitic structure for guide-roll materials was developed using centrifugal casting instead of classic overlay welding process. Centrifugal casting offered a simpler process, fewer defects and even microstructures. Especially in terms of thermal fatigue cracking which usually occurs in the HAZ of welding beads of used continuous caster guide roll materials made by overlay welding process. A typical tensile strength of 1,600 MPa was obtained by this process and was higher than typical tensile strength($800{\sim}1,200\;MPa$) with overlay welding technique. Tempering at $400{\sim}550^{\circ}C$ for 2 hrs was observed to have significant precipitate hardening effect which increases strength and elongation. Nitrogen content from the Cr-N input in the casting process was found to have positive contribution to decrease the volume fraction of ${\delta}$-ferrite which directly corresponds to increasing strength of the roll materials.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 Proceedings of the Korea Automatic Control Conference, 11th (KACC); Pohang, Korea; 24-26 Oct. 1996
• /
• pp.319-323
• /
• 1996

A new steel-making process, strip-casting, is introduced. The strip-casting is a new technique making the thin steel strip from the molten steel directly without resorting to repetitive reheating and hot-rolling required in a conventional steel-making method. This paper derives the mathematical model of strip caster, proposes a control strategy for stable startup operation and a fuzzy decision making rule for automatic control mode change in strip-casting process.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제2권2호
• /
• pp.146-152
• /
• 2002

Mold level control has been a major control task for continuous casting plants. The system involves nonlinearities such as stick-slip friction in the sliding gate, time-delay, friction force variations between molten steel and the inner wall of mold, and nozzle logging/unclogging. These complex problems should be solved to control mold level for steel cast. In this paper, we propose a neural fuzzy mold level control technique for solving these complex problems and give experiment studies to show the mold level control in continuous casting process.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.250-253
• /
• 2004

A finite element model is developed for the process of squeeze casting of metal matrix composites. The fluid flow and the heat transfer are fundamental phenomena in squeeze casting. The equations for the clear fluid flow and the flow in porous media are used to simulate the transient metal flow. To describe heat transfer in the solidification of molten aluminum, the energy equation is written in terms of temperature and enthalpy. A direct iteration technique is used to solve the resulting nonlinear algebraic equations. The cooling curves and temperature distribution during infiltration and solidification were calculated for a simplified model with pure aluminum. The developed program can be used for squeeze casting process of complex geometry, boundary conditions and processing parameter optimization.

• 열처리공학회지
• /
• 제17권5호
• /
• pp.293-298
• /
• 2004

For the application of heat sink device, the green sheets of powder of W-XCu and Mo-XCu composites were fabricated by tape casting technique. The mixing ratio of powder and binder was 6:4. The green sheet was shrinked up to 10~20% after sintering and the maximum relative density was above 95%. Thermal conductivity and Thermal expansion systematically increased with increasing Cu contents. The maximum thermal conductivity of W-20wt.%Cu was about 206[W/mK].