• 한국진공학회지
• /
• 제18권4호
• /
• pp.259-265
• /
• 2009

본 연구에서는 열증착법을 이용하여 합성된 단결정의 산화아연 나노선들을 이용하여 전계효과트랜지스터를 제작하여 광학, 표면반응 및 전기화학적인 거동들에 대한 기초 연구들을 수행하였다. 100 nm의 지름과 길이 5 um 길이를 갖는 단결정 산화아연나노선의 전자 농도와 이동도는 각각 $1.30{\times}10^{18}cm^{-3}$과 $15.6cm^2V^{-1}s^{-1}$이었으며, 자외선을 나노선에 조사한 경우 약 400배 정도 전류가 증가하였다. 또한 나노선들은 여러 농도의 수소와 일산화탄소에 대해 잘 알려진 표면반응으로 기인한 기체 감지 특성을 보였고, 0.1 M NaCl 전해질 내에서 전형적인 산화아연의 나노선의 전기적 특성을 유지함을 확인하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.166-166
• /
• 2010

Recently, TFTs based on amorphous oxide semiconductors (AOSs) such as ZnO, InZnO, ZnSnO, GaZnO, TiOx, InGaZnO(IGZO), SnGaZnO, etc. have been attracting a grate deal of attention as potential alternatives to existing TFT technology to meet emerging technological demands where Si-based or organic electronics cannot provide a solution. Since, in 2003, Masuda et al. and Nomura et al. have reported on transparent TFTs using ZnO and IGZO as active layers, respectively, much efforts have been devoted to develop oxide TFTs using aforementioned amorphous oxide semiconductors as their active layers. In this thesis, I report on the performance of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer at room temperature. $SiO_2$ was employed as the gate dielectric oxide. The amorphous indium gallium zinc oxides were deposited by RF magnetron sputtering. The carrier concentration of amorphous indium gallium zinc oxide was controlled by oxygen pressure in the sputtering ambient. Devices are realized that display a threshold voltage of 1.5V and an on/off ration of > $10^9$ operated as an n-type enhancement mode with saturation mobility with $9.06\;cm^2/V{\cdot}s$. The devices show optical transmittance above 80% in the visible range. In conclusion, the fabrication and characterization of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer were reported. The operation of the devices was an n-type enhancement mode with good saturation characteristics.

• 센서학회지
• /
• 제6권1호
• /
• pp.49-55
• /
• 1997

스퍼터링 방법에 의하여 유리 기판위에 ZnO 박막을 형성하여 증착막의 전기, 광학적 특성을 조사하였다. 실온에서 180 W의 고주파 전력과 $1{\times}10^{-3}$ Torr의 스퍼터링 압력일 때 증착된 박막에서 가장 강한 c축 배향성과 가장 낮은 저항률 값($1{\times}10^{-4}{\Omega}{\cdot}cm$)을 나타내었고, 이 때의 캐리어 농도 및 홀 이동도는 각각 $6.27{\times}10^{20}cm^{-3}$와 $22.04cm^{2}/V{\cdot}s$이었다. 증착된 ZnO 박막의 가시광 투과율은 90% 이상을 나타내었으며 330 nm 이하의 자외선 영역과 830 nm 이상의 적외선 영역에서는 뛰어난 광 차단 효과를 나타내었다. 또한 증착된 박막을 수소 분위기에서 열처리함으로써 저항률이 감소하였고, 안정된 박막을 얻을 수 있었다.

• 한국결정성장학회지
• /
• 제9권6호
• /
• pp.542-546
• /
• 1999

InP single crystal, III-V binary compound semiconductor, was grown by VGF(vertical gradient freeze) method using quartz ampoule and its electrical optical properties were investigated. Phosphorous powders were put in the bottom of quartz ampoule and Indium metal charged in conical quartz crucible what was attached at the upper side position inside the quartz ampoule. It was vacuous under the pressure of $10^5$Torr and sealed up. Indium metal was melted at $1070^{\circ}C$ and InP composition was formed by diffusion of phosphorous sublimated at $450^{\circ}C$ into Indium melt. By cooling the InP composition melt ($2^{\circ}C$~$5^{\circ}C$/hr of cooling rate) in range of $1070^{\circ}C$~$900^{\circ}C$, InP crystal was grown. The grown InP single crystals were investigated by X-ray analysis and polarized optical microscopy. Electrical properties were measured by Van der Pauw method. At the cooling method. At the cooling rate of $2^{\circ}C$/hr, growth direction of ingot was [111] and the quality of ingot was better at the upper side of ingot than the lower side. It was found that the InP crystals were n-type semiconductor and the carrier concentration, electron mobility and relative resistivity were $10^{15}$~$10^{16}/\textrm{cm}^3$ , $2\times 10^3$~$3\times 10^4{\textrm}{cm}^2$/Vsec and$2\times 10^{-1}$~$2\times 10^{-3}$/ Wcm in the range of 150K~300K, respectively.

• Journal of Electrochemical Science and Technology
• /
• 제8권3호
• /
• pp.206-214
• /
• 2017

SnS films have been prepared by electrodeposition technique onto Cu and ITO substrates using acidic solutions containing tin chloride and sodium thiosulfate with sodium citrate as an additive. The effects of sodium citrate on the electrochemical behavior of electrolyte bath containing tin chloride and sodium thiosulfate were investigated by cyclic voltammetry and chronoamperometry techniques. Deposited films were characterized by XRD, FTIR, SEM, optical, photoelectrochemical, and electrical measurements. XRD data showed that deposited SnS with sodium citrate on both substrates were polycrystalline with orthorhombic structures and preferential orientations along (111) directions. However, SnS films with sodium citrate on Cu substrate exhibited a good crystalline structure if compared with that deposited on ITO substrates. FTIR results confirmed the presence of SnS films at peaks 1384 and $560cm^{-1}$. SEM images revealed that SnS with sodium citrate on Cu substrate are well covered with a smooth and uniform surface morphology than deposited on ITO substrate. The direct band gap of the films is about 1.3 eV. p-type semiconductor conduction of SnS was confirmed by photoelectrochemical and Hall Effect measurements. Electrical properties of SnS films showed a low electrical resistivity of $30{\Omega}cm$, carrier concentration of $2.6{\times}10^{15}cm^{-3}$ and mobility of $80cm^2V^{-1}s^{-1}$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 논문집 센서 박막재료연구회 및 광주 전남지부
• /
• pp.15-17
• /
• 2008

$CuInS_2$ thin films were synthesized by sulpurization of Cu/In Stacked elemental layer deposited onto glass Substrates by vacuum furance annealing at temperature 200[$^{\circ}C$]. And structural and electrical properties were measured in order to certify optimum conditions for growth of the ternary compound semiconductor $CuInS_2$ thin films with non-stoichiometry composition. $CuInS_2$ thin film was well made at the heat treatment 200[$^{\circ}C$] of SLG/Cu/In/S stacked elemental layer which was prepared by thermal evaporator, and chemical composition of the thin film was analyzed nearly as the proportion of 1 : 1 : 2. Physical properties of the thin film were investigated at various fabrication conditions substrate temperature, annealing and temperature, annealing time by XRD, FE-SEM and hall measurement system. At the same time, carrier concentration, hall mobility and resistivity of the thin films was $9.10568{\times}10^{17}[cm^{-3}]$, 312.502[$cm^2/V{\cdot}s$] and $2.36{\times}10^{-2}[{\Omega}{\cdot}cm]$, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 광주전남지부
• /
• pp.68-70
• /
• 2006

$CuInS_2$ thin films were synthesized by sulpurization of Cu/In Stacked elemental layer deposited onto glass Substrates by vacuum furance annealing at temperature 200[$^{\circ}C$]. And structural and electrical properties were measured in order to certify optimum conditions for growth of the ternary compound semiconductor $CuInS_2$ thin films with non-stoichiometry composition. $CuInS_2$ thin film was well made at the heat treatment 200 [$^{\circ}C$] of SLG/Cu/In/S stacked elemental layer which was prepared by thermal evaporator, and chemical composition of the thin film was analyzed nearly as the proportion of 1:1:2. Physical properties of the thin film were investigated at various fabrication conditions substrate temperature, annealing and temperature, annealing time by XRD, FE-SEM and hall measurement system. At the same time, carrier concentration, hall mobility and resistivity of the thin films was $9.10568{\times}10^{17}[cm^{-3}]$, $312.502[cm^2/V{\cdot}s]$ and $2.36{\times}10^{-2}[{\Omega}{\cdot}cm]$, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.28-28
• /
• 2009

Fabrications of antireflection structures on solar cell were investigated to trap the light and to improve quantum efficiency. Introductions of patterned substrate or textured layer for Si solar cell were performed to prevent reflectance and to increase the path length of incoming light. However, it is difficult to deposit conformally flat electrode on perpendicular plane. ZnO is II-VI compound semiconductor and well-known wide band-gap material. It has similar electrical and optical properties as ITO, but it is nontoxic and stable. In this study, Al-doped ZnO thin films are deposited as transparent electrode by atomic layer deposition method to coat on Si substrate with micro-scale structures. The deposited AZO layer is flatted on horizontal plane as well as perpendicular one with conformal 200 nm thickness. The carrier concentration, mobility and resistivity of deposited AZO thin film on glass substrate were measured $1.4\times10^{20}cm^{-3}$, $93.3cm^2/Vs$, $4.732\times10^{-4}{\Omega}cm$ with high transmittance over 80%. The AZO films were coated with polyimide and performed selective polyimide stripping on head of column by reactive ion etching to measure resistance along columns surface. Current between the micro-columns flows onto the perpendicular plane of deposited AZO film with low resistance.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.337-337
• /
• 2013

ZnO seed layers were deposited on a quartz substrate using the sol-gel method, and B-doped ZnO (BZO) nanorods with different B concentrations ranging from 0 to 2.5 at.% were grown on the ZnO seed layers by the hydrothermal method. The structural, optical, electrical propertiesof the ZnO and BZO nanorods were investigated using field-emission scanning electron microscopy, X-ray diffraction (XRD), photoluminescence (PL), ultraviolet-visible spectroscopy, and hall effect. The ZnO and BZO nanorods grew well aligned on the surface of the quartz substrates. From the XRD data, it can be seen that the B doping is responsible for the distortion of the ZnO lattice. The PL spectra show near-band-edge emission and deep-level emission, and they also show that B doping significantly affects the PL properties of ZnO nanorods. The optical band gaps are changed by B doping, and thus the Urbach energy value changed with the optical band gap of the ZnO nanorods. From the hall measurements, it can be observed that the values of electrical resistivity, carrier concentration, and mobility are changed by B doping.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.261-262
• /
• 2006

$CuInS_2$ thin films were synthesized by sulpurization of Cu/In Stacked elemental layer deposited onto glass Substrates by vacuum furance annealing at temperature 200[$^{\circ}C$]. And structural and electrical properties were measured in order to certify optimum conditions for growth of the ternary compound semiconductor $CuInS_2$ thin films with non-stoichiometry composition. $CuInS_2$ thin film was well made at the heat treatment 200[$^{\circ}C$] of SLG/Cu/In/S stacked elemental layer which was prepared by thermal evaporator, and chemical composition of the thin film was analyzed nearly as the proportion of 1:1:2. Physical properties of the thin film were investigated at various fabrication conditions substrate temperature, annealing and temperature, annealing time by XRD, FE-SEM and hall measurement system. At the same time, carrier concentration, hall mobility and resistivity of the thin films was $9.10568{\times}10^{17}[cm^{-3}]$, 312.502 [$cm^2/V{\cdot}s$] and $2.36{\times}10^{-2}[{\Omega}{\cdot}cm]$, respectively.