• Journal of Surface Science and Engineering
• /
• v.50 no.3
• /
• pp.198-205
• /
• 2017

Thermal dissipation was investigated for poly methyl methacrylate (PMMA) composite films containing graphite and multi wall carbon nanotube(CNT) powders as filler materials. After mixing PMMA with fillers, solvent, and dispersant, the pastes were prepared by passing through a three roll mill for three times. The prepared pastes were coated $15{\sim}40{\mu}m$ thick on a side of 0.4 mm thick aluminium alloy plate and dried for 30 min at $150^{\circ}C$ in an oven. The content of fillers in dried films was varied as 1, 2, and 5 weight % maintaining the ratio of graphite and CNT as 1:1. Raman spectra from three different samples exhibited D, G and 2D peaks, as commonly observed in graphite and multi wall CNT. Among those peaks, D peak was prominent, which manifested the presence of defects in carbon materials. Thermal emissivity values of three samples were measured as 0.916, 0.934, and 0.930 with increasing filler content, which were the highest ever reported for the similar composite films. The thermal conductivities of three films were measured as 0.461, 0.523, and $0.852W/m{\cdot}K$, respectively. After placing bare Al plate and film coated samples over an opening of a polystyrene box maintained for 1 h at $92^{\circ}C$, the temperatures inside and outside of the box were measured. Outside temperatures were lower by $5.4^{\circ}C$ in the case of film coated plates than the bare one, and inside temperatures of the former were lower by $3.6^{\circ}C$ than the latter. It can be interpreted that the PMMA composite film coated Al plates dissipate heat quicker than the bare Al plate.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.554-560
• /
• 2009

We investigate a method for the electrochemical preparation of titanium dioxide/carbon nanotube ($TiO_2$/CNT) composites involving the electroplating of Ti in a titanium n-butoxide (TNB) electrolyte into a CNT matrix. The Brunauer-Emmett-Teller (BET) surface areas of $TiO_2$/CNT composites decrease as the electrochemical operating time increases. Changes in XRD patterns show a typical anatase type on the $TiO_2$/CNT composite prepared with a CNT matrix by the electroplating method in a TNB solution. In SEM micrographs, the titanium complex particles are uniformly distributed on the CNT surface. The results of chemical elemental analysis for the $TiO_2$/CNT composites show that most of the spectra for these samples produce stronger peaks for carbon and Ti metal than for any other element. Finally, the prominent photoelectrocatalytic activities of the $TiO_2$/CNT composites can be attributed to the combined effects of photodegradation of $TiO_2$, electron assistance of CNT, and the application of a sufficient voltage.

• Journal of the Korean Ceramic Society
• /
• v.46 no.4
• /
• pp.357-364
• /
• 2009

We investigate a method for the electrochemical preparation of titanium dioxide/carbon nanotube ($TiO_2$/CNT) composites involving the electroplating of Ti in a titanium n-butoxide (TNB) electrolyte into a CNT matrix. The BET surface areas of $TiO_2$/CNT composites decreased as electrochemical operating time increased. Changes in XRD patterns showed a typical anatase type on the $TiO_2$/CNT composite prepared with a CNT matrix by the electroplating method in the TNB solution. In SEM micrographs, the titanium complex particles were uniformly distributed on the CNT surface. The results of chemical elemental analysis for the $TiO_2$/CNT composites showed that most of the spectra for these samples produced stronger peaks for carbon and Ti metal than those of any other element. Finally, the prominent photoelectrocatalytic (PEC) activities of the $TiO_2$/CNT composites could be attributed to the combined effects of photodegradation of $TiO_2$, electron assistance of CNT and the application of a sufficient voltage.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.3
• /
• pp.112-121
• /
• 2019

In this study, silicon / carbon nanotube / carbon composite particles with high capacity were fabricated by using micro-sized silicon particles and carbon nanotubes as an anode material for lithium ion batteries. The silicon / carbon nanotube / carbon composite particles were prepared by spray drying method to prepare spherical composite particles. The composite particles have the network structure of the carbon nanotubes around the silicon particles, in which the silicon particles and the carbon nanotubes are bonded by amorphous carbon. It appears that the volume expansion of silicon is effectively buffered and the electrical contact is maintained in the network structure of the composite particles during charge-discharge cycles.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.30 no.1
• /
• pp.1-9
• /
• 2020

Objectives: The purpose of this case study is to assess workers' exposure to carbon nanotubes(CNTs) and characterize particles aerosolized during the process of producing CNT-enabled polytetrafuoroethylene(PTFE) composites at a worksite in Korea. Methods: Personal breathing zone and area samples were collected for determining respirable concentrations of elemental carbon(EC) using NIOSH(National Institute for Occupational Safety and Health) Method 5040. Personal exposure to nano-sized particles was measured as the number concentration and mean diameter using personal ultrafine particle monitors. The number concentration by particle size was measured using optical particle sizers(OPS) and scanning mobility particle sizers(SMPS). Transmission electron microscopy (TEM) area samples were collected on TEM grids and analyzed to characterize the size, morphology, and chemistry of the particles. Results: Respirable EC concentrations ranged from 0.04 to 0.24 ㎍/㎥, which were below 23% of the exposure limit recommended by NIOSH and lower than background concentrations. Number concentrations by particle size measured using OPS and SMPS were not noticeably elevated during CNT-PTFE composite work. Instant increase of number concentrations of nano-sized particles was observed during manual sanding of CNT-PTFE composites. Both number concentrations and mean diameters did not show a statistically significant difference between workers handing CNT-added and not-added materials. TEM analyses revealed the emission of free-standing CNTs and CNT-PTFE aggregate particles from the powder supply task and composite particles embedded with CNTs from the computer numerical control(CNC) machining task with more than tens of micrometers in diameter. No free-standing CNT particles were observed from the CNC machining task. Conclusions: Significant worker exposure to respirable CNTs was not found, but the aerosolization of CNTs and CNT-embedded composite particles were observed during handing of CNT-PTFE powders and CNC machining of CNT-PTFE composites. Considering the limited knowledge on the toxicity of CNTs and CNT composite particles to date, it seems prudent to take a precautionary approach for the protection of workers' health.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.150.1-150.1
• /
• 2005

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.152-152
• /
• 2004

카본나노튜브(Carbon Nanotube)는 다른 물질과 구별되는 날카로움(Sharpness), 고세장비(High Aspect Ratio), 높은 기계적 강성(Stiffness), 고탄성(high Elasticity), 그리고 반도체(semi-conducting)와 도체(Metallic) 성질 때문에, 카본나노튜브는 많은 연구에 적용되고 있으며, 카본나노튜브가 부착된 AFM(Atomic Force Microscope) 팁을 이용한 AFM 측정은 CNT 응용에 있어서 매우 큰 효과를 내는 응용분야 중 하나이다. AEM 팁에 카본나노튜브를 붙이는 이전 연구는 대부분 화학증착법(Chemical Vapor Deposition)에 의해 이루어 졌으며, 매우 효과적인 방법이지만 고가의 장비와 고온의 챔버내에서 이루어진다는 문제점을 가지고 있다.(중략)

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10b
• /
• pp.223-224
• /
• 2003

Polyimides (PI) are widely used in applications ranging from microelectronics to aerospace. Due to their insulating nature, significant accumulation of electrostatic charge may result on their surface, causing local heating and premature degradation to electronic components or space structures. Over the past decade, several publications have been made in fabrication and charaterization of CNT nanocomposites [1,2]. (omitted)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.935-936
• /
• 2011

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.7
• /
• pp.594-598
• /
• 2008

The metal catalyst particles which there is as impurities on a tip part of carbon nanotube (CNT) are not good to apply it to a nano-electronic device. It was very important the opening of CNT-tip to fix a target bio material and a material to accept in CNT in a biosensor, so we performed $HNO_3$ wet etching to remove the metal catalyst particle which there was on a tip part of CNT grown up in the study and observed the opened CNT-tip with etching time. We synthesized the CNTs using a HF-PECVD method and choses the CNT length of 700 nm for the application of nano-electronic device such as a biosensor etc.. We observed the opened CNT-tip with wet etching times of $HNO_3$ (10, 30, 60 min). From the results, we observed that the CNT-tip was opened with the increase of wet etching time lively. In case of CNTs etched during 60 min, we confirmed that there was not the ratio of Ni included in CNTsI as catalyst. Conclusively, in the case of CNT etched for 60 minutes, it is completely good for application of a biosensor and, in addition, the metal-free CNTs will contribute to the application of other nanoelectronic devices.