• Polymer(Korea)
• /
• v.30 no.5
• /
• pp.385-390
• /
• 2006

In this work, the effect of carbon nanofiber (CNF) on thermal properties, and friction and wear behavior of CNF/PMMA composites were examined. While thermal properties of the composites were investigated with differential scanning calorimetry, thermograyimetric analyzer, and dynamic mechanical analyzer friction and wear behaviors were examined using a friction and wear tester. The glass transition temperature (Tg), integral procedural decomposition temperature (IPDT), storage modulus (E'), and tan ${\delta}$ appeared at higher temperatures with increasing CNF content, which were probably attributed to the presence of strong interactions between the carbonaceous fillers and the PMMA resins matrix. The wear loss in the composites decreased at 0.1 wt% CNF and then increased with 5-10 wt% CNF content. This was due to the existence of large aspect ratio CNF in PMMA which led to an alignment of PMMA chains and an increase of mechanical interlocking, resulting in the formation of crosslinked structures between CNF and PMMA in the composite.

• Journal of Adhesion and Interface
• /
• v.9 no.1
• /
• pp.3-8
• /
• 2008

Self-sensing was evaluated for carbon nanofiber (CNF)/epoxy composites with two different aspect ratios via electro-micromechanical technique and wettability test. Volumetric electrical resistance was measured to evaluate the comparative dispersion degree indirectly and it decreased due to the increase of electric contacts with increasing CNF concentration. The dispersion degree was evaluated indirectly by calculating coefficient of variation (COV) of volumetric electrical resistance. The CNF type A with a high aspect ratio showed better self-sensing than the case of CNF type B with a short aspect ratio. The CNF type B/epoxy composite showed little self-sensing at a concentration higher than 2 vol% probably due to poor dispersion. The apparent modulus of CNF type B was higher than that of CNF type A due to the orientation effect and the high surface area. The thermodynamic work of adhesion was consistent with the result of apparent modulus.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10b
• /
• pp.114-117
• /
• 2003

Conventional heating the heat source cause the molecules to react from the surface toward the center so that successive layers of molecules heat in turn. The product surfaces may be in danger of over heating by the time heat penetrates the material. Microwave, however, produce a volume heating effect. All molecules are set in action at the same time. It also evens temperature gradients and offers other important benefits such as selective heating. (omitted)

• Bulletin of the Korean Chemical Society
• /
• v.31 no.12
• /
• pp.3852-3855
• /
• 2010

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.5
• /
• pp.265-269
• /
• 2014

Carbon nanofiber electrode has been fabricated for energy storage systems by the electrospinning of SU-8 precursor and subsequent pyrolysis. Various parameters including the applied voltage, the distance between syringe tip and target collector and the flow rate of the polymer affect the diameter of SU-8 electrospun nanofibers. Shrinkage during pyrolysis decreases the fiber diameter. As the pyrolysis temperature increases, the resistivity decreases dramatically. Low resistivity is one of the important characteristics of the electrodes of an energy storage device. Given the advantages of carbon nanofibers having high external surface area, electrical conductivity, and lithium intercalation ability, SU-8 derived carbon nanofibers were applied to the anode of a full lithium ion cell. In this paper, we studied the physical properties of carbon fiber electrode by scanning transmission microscopy, thermal gravimetric analysis, and four-point probe. The electrochemical characteristics of the electrode were investigated by cyclic voltammogram and electrochemical impedance spectroscopy plots.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.4024-4031
• /
• 2014

Nanofibers have attracted significant interest in many industrial fields because their high surface area and porosity. In addition, the continued use of petrochemical based polymers has caused the depletion of oil resources and accelerated the greenhouse effect by the emission of carbon dioxide. Therefore, biomass-based polymer has become a very important environmentally friendly alternative. In this study, nanofibers were fabricated by an electrospinning process using biomass based PEF(polyethylene furoate) prepared by the polymerization of 2,5-furandicaboxylic acid and ethylene glycol. Furthermore, the electrospun nanofiber was strongly affected by various parameters, such as the solvent, polymer concentration and electric field. In conclusion, nanofibers with an average fiber diameters of 200 - 700 nm could be prepared at polymer concentration of 15 wt% using HFIP, and their fiber diameter increased with increasing electric field.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.680-685
• /
• 2005

Multi-walled carbon nanotubes were purified by using the nitric acid after the mechanical cutting, which carboxylic group might be introduced into the surface of nanotubes. To enhance the dispersion of CNTs, carboxylic groups were substituted in the reaction with octadecyl amine containing a long alkyl group. Nanofibers were manufactured by electrospinning, the solution that mixed with PMMA and ODA-fuctionalized CNTs in dimethyl formamide and dispersed with ultrasonication. Diameter and alignment of nanofibers with various electrospinning parameters, such as the CNT and PMMA concentration in solution, the applied voltage, and the distance to the collector were investigated. As a result, the nanofiber diameter was increased with the increment of PMMA concentration, whereas it was reduced as the applied voltage and the spinning distance was increased. The spinning area became smaller with the distance. The nanofibers were formed without the defect on surface and well aligned in a specific concentration of PMMA and nanotubes.

• Korean Journal of Metals and Materials
• /
• v.50 no.10
• /
• pp.763-768
• /
• 2012

The uniform and highly smooth nanofibers of biocompatible poly(${\varepsilon}$-caprolactone) (PCL) composited with different contents of multiwalled carbon nanotubes (MWCNTs) were successfully prepared by electrospinning. Experimental parameters were MWCNTs addition to a PCL solution and applied voltages. The topographical features of the composite nanofibers were characterized by scanning electron microscopy and its electrical properties were measured by a four-point probe method. The surface resistance gradually decreased with an increasing content of MWCNTs in PCL fibers because of the excellent electrical conductivity of MWCNTs. The nanofiber diameter could be regulated by varying the solution viscosity and voltages. Our results establish that this kind of electrospinning PCL/MWCNTs nanofibers with the control of fiber diameter and electrical conductivity may be a promising candidate for the application of scaffolds in tissue engineering.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.412-412
• /
• 2016

염료감응 태양전지(dye-sensitized solar cells, DSSCs)는 식물의 광합성원리와 매우 유사한 작동원리를 갖고 있는 전지이며, 간단한 구조, 저렴한 제조단가, 친환경성 등의 등의 장점으로 인하여 많은 관심을 모으고 있다. 이러한 염료감응 태양전지는 빛을 받아들인 염료분자가 전자-홀 쌍을 생성하며 전자는 반도체 산화물을 통해 이동되고 전해질의 산화환원 과정을 통해 염료 분자가 다시 환원되는 순환메커니즘을 따르고 있다. 일반적으로 염료감응 태양전지는 밴드 갭 에너지가 큰 반도체 산화물을 포함하는 작업전극, 산화환원 반응을 통해 전자를 염료로 보내는 전해질, 환원 촉매역할을 하는 상대전극으로 구성되어 있다. 특히, 상대전극으로는 우수한 촉매특성과 높은 전도성을 갖는 백금이 가장 많이 이용되고 있지만 가격이 비싸고 요오드에 취약하기 때문에 상용화에 큰 장애물이다. 따라서, 백금을 대체하기 위해 저가의 탄소나 고분자에 대한 연구가 활발히 진행되고 있고, 그 중 탄소나노섬유(carbon nanofiber, CNFs)는 높은 표면적과 뛰어난 화학적 안정성으로 촉매효율을 증대시킬 수 있어 촉매물질로서 관심이 높아지고 있다. 본 연구에서는 상대전극에 탄소나노섬유기반 복합체를 합성하였고, 성공적으로 저가격 및 고성능의 염료감응 태양전지를 제작하였다. 이때, 지지체인 탄소나노섬유는 전기방사법을 통해 합성하였으며, 수열합성법을 이용하여 금속산화물을 담지하였다. 이렇게 제작된 탄소나노섬유-Fe2O3 복합체는 scanning electron microscopy, transmission electron microscopy, X-ray diffraction, 그리고 X-ray photoelectron spectroscopy 통해 구조적, 화학적 특성을 평가하였으며 전기화학적 특성 및 광전변환 효율을 분석하기 위해 cyclic voltammetry, electrochemical impedance spectroscopy, 그리고 solar simulator를 사용하였다. 본 학회에서 위와 관련된 더 자세한 사항에 대해 논의할 것이다.

• Membrane Journal
• /
• v.31 no.6
• /
• pp.426-433
• /
• 2021

In this study, a novel material polyketone (PK) was chosen and PK micro/nano fiber membranes were fabricated via electrospinning method under various conditions. After that, the potential application in oil-water separation was thoroughly investigated. The surface of microfiber membrane formed under high humidity especially became much rougher than that formed under low humidity. When salt was added to the spinning solution, the diameter of fibers was reduced up to 90% and the nanofiber membranes could be formed. The oil/water emulsions were prepared and separated under gravity condition using the manufactured rPK-LNC and PK-H membranes. The separation characteristics was evaluated by measuring total organic carbon (TOC) and turbidity. Meanwhile, the changes in the physical properties of fiber membranes under various conditions and with or without salt, as well as the changes in oil water separation characteristics were also studied.