• 한국지반환경공학회 논문집
• /
• 제17권2호
• /
• pp.5-11
• /
• 2016

다층벽탄소나노튜브(MWCNT)와 titanium(IV) butoxide(TNB) 그리고 silver nitrate($AgNO_3$)를 이용하여 졸-겔법으로 $MWCNT-TiO_2$ 복합체와 $Ag-MWCNT-TiO_2$ 복합체를 제조하였다. 복합체에서의 Ag의 분산 및 구조를 주사전자현미경(SEM)과 투과전자현미경(FE-TEM)으로 관찰하였다. X선 회절 분석기(XRD)를 이용하여 복합체의 패턴을 보았을 때 anatase 결정구조를 확인할 수 있었다. 에너지 분광 분석기(EDX)로 원소성분을 분석한 결과 주요 원소인 C, Ti, O 그리고 Ag가 확인되었다. $TiO_2$ 입자는 MWCNT에 균일하게 분산되었고, Ag 입자는 튜브 표면에 고정되었다. 또한 UV 조사 시간에 따른 메틸렌블루의 분해를 통하여 광촉매 활성평가를 하였다. $Ag-MWCNT-TiO_2$ 복합체는 $MWCNT-TiO_2$ 복합체보다 높은 광분해능을 보였다. Ag의 높은 전도성이 $MWCNT-TiO_2$ 복합체의 광활성을 향상 시킨다는 결과를 나타냈다.

• 한국표면공학회지
• /
• 제48권6호
• /
• pp.309-314
• /
• 2015

Multiwall carbon nanotubes are synthesized by using VLS mechanism for the application to $H_2$ gas sensor. MWCNT is not suitable for hydrogen gas sensor due to its low response to the gas. To enhance the gas sensing performance, multiwall carbon nanotubes are coated with $TiO_2$ nanoparticles. Scanning electron microscopy and Transmission electron microscopy showed that the synthesized MWCNT were well dispersed with the diameter and wall thickness of approximately 10-30nm and 5nm, respectively. The MWCNT sensor showed the sensitivities of 1.33-9.5% for the $H_2$ concentration of 100-5000ppm at room temperature. These sensitivities are significantly improved to 6.64-46.65% by coating $TiO_2$ nanoparticles to the MWCNT sensor. The mechanisms of $H_2$ gas sensing improvement of the MWCNT sensor coated with $TiO_2$ nanoparticles are discussed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1678-1683
• /
• 2003

DBD(Dielectric Barrier Discharge) plasma in air is well established for the production of large quantities of ozone and is more recently being applied to aftertreatment processes for HAPs(Hazardous Air Pollutants). Although DBD high electron density and energy, its potential use as nano and sub-micron sized particle charging are not well known. Aim of this work is to determine design and operating parameters of a two-stage ESP with DBD. DBD and ESP are used as particle charger and precipitator, respectively. We measured particle precipitation efficiency of two-stage ESP and estimated ozone decomposition of both pelletized $MnO_2$ catalyst and pelletized activated carbon. To examine the particle precipitation efficiency, nano and sub-micron sized particles were generated by a tube furnace and an atomizer. AC voltage of $7{\sim}10$ kV(rms) and 60 Hz is used as DBD plasma source. DC -8 kV is applied to the ESP for particle precipitation. The overall particle collection efficiency for the two-stage ESP with DBD is over 85 % under 0.64 m/s face velocity. Ozone decomposition efficiency with pelletized $MnO_2$ catalyst or pelletized activated carbon packed bed is over 90 % when the face velocity is under 0.4 m/s in dry air.

• 접착 및 계면
• /
• 제11권4호
• /
• pp.174-180
• /
• 2010

다중벽탄소나노튜브를 표면처리하여 polymethylmethacrylate (PMMA) 기재에 첨가하여 제조한 고분자 복합재료에서 탄소나노튜브의 표면처리가 계면 및 열전도도에 미치는 효과를 고찰하였다. Coagulation 방법과 atomic transfer radical polymerization (ATRP) 방법을 사용하여 탄소나노튜브를 표면 처리 하여 사용하였으며, ATRP 방법을 적용하여 제조한 복합재료는 coagulation 방법을 사용하여 제조한 복합재료보다 높은 열전도도와 투과도를 가졌다. 순수 PMMA의 열전도도가 0.21 W/mK인데 비하여 ATRP 방법으로 처리한 1 wt%의 탄소나노튜브를 첨가하였을 경우 0.38 W/mK로 열전도도가 향상되었다. 탄소나노튜브와 PMMA기재의 계면을 주사전자현미경을 이용하여 관찰한 결과 탄소나노튜브의 표면처리에 의해 기재 내에 분산이 향상되고 고분자기재-탄소나노튜브 계면에서의 접촉이 용이해져 포논산란이 감소되어 광 투과성을 가지면서 열전도도가 향상된 것으로 보인다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.301-301
• /
• 2003

In current study, Nanocomposites are reinforced with carbon nanofiber, carbon nanotube and SiC, etc. Since the nano reinforcements have the excellent mechanical, thermal and electrical properties compared with that of existing composites, it has lately attracted considerable attention in the various areas. Cu have been widely used as signal transmission materials for electrical electronic components owing to its high electrical conductivity. However, it's size have been limited to small ones due to its poor mechanical properties. Until now, strengthening of the copper alloy was obtained either by the solid solution and precipitation hardening by adding alloy elements or the work hardening by deformation process. Adding the alloy elements lead to reduction of electrical conductivity. In this aspect, if carbon nanofiber is used as reinforcement which have outstanding mechanical strength and electric conductivity, it is possible to develope Cu matrix nanocomposite having almost no loss of electric conductivity. It is expected to be innovative in electric conducting material market. The unidirectional alignment of carbon nanofiber is the most challenging task developing the cooer matrix composites of high strength and electric conductivity. In this study, the unidirectional alignment of carbon nanofibers which is used reinforced material are controlled by drawing process and align mechanism as well as optimized drawing process parameter are verified via numerical analysis. The materials used in this study were pure copper and the nanofibers of 150nm in diameter and of 10∼20$\mu\textrm{m}$ in length. The materials have been tested and the tensile strength was 75MPa with the elongation of 44% for the copper. it is assumed that carbon nanofiber behave like porous elasto-plastic materials. Compaction test was conducted to obtain constitutive properties of carbon nanofiber Optimal parameter for drawing process was obtained by analytical and numerical analysis considering the various drawing angles, reduction areas, friction coefficient, etc. The lower drawing angles and lower reduction areas provides the less rupture of co tube is noticed during the drawing process and the better alignment of carbon nanofiber is obtained.

• 한국분말재료학회지
• /
• 제21권1호
• /
• pp.28-33
• /
• 2014

This paper describes the surface modification effect of a Ti substrate for improved dispersibility of the catalytic metal. Etching of a pure titanium substrate was conducted in 50% $H_2SO_4$, $50^{\circ}C$ for 1 h-12 h to observe the surface roughness as a function of the etching time. At 1 h, the grain boundaries were obvious and the crystal grains were distinguishable. The grain surface showed micro-porosities owing to the formation of micro-pits less than $1{\mu}m$ in diameter. The depths of the grain boundary and micro-pits appear to increase with etching time. After synthesizing the catalytic metal and growing the carbon nano tube (CNT) on Ti substrate with varying surface roughness, the distribution trends of the catalytic metal and grown CNT on Ti substrate are discussed from a micro-structural perspective.

• 한국세라믹학회지
• /
• 제51권6호
• /
• pp.544-548
• /
• 2014

Aluminum nitride was synthesized using a carbothermal method from mesoporous alumina having a high surface area (> $1,000m^2/g$) as an aluminum source and CNTs (carbon nano tubes) as a carbon source. In this case the mesoporous alumina was used as the starting material instead of ${\alpha}-Al_2O_3$ with the expectation that the mesopores in mesoporous alumina act as channels for N2 gas and elimination of CO generated as by-product. It is also expected that the synthetic temperature should be lower compared to the use of ${\alpha}-Al_2O_3$ as a starting material due to its high surface area. The crystallinity of the produced aluminum nitride was studied by XRD and FT-IR, and the microstructure was investigated by FE-SEM. Also the purity of the aluminum nitride was analyzed through N/O determinator and ICP analysis.

• 한국전기전자재료학회논문지
• /
• 제22권12호
• /
• pp.1089-1094
• /
• 2009

Carbon nanotubes (CNTs) have excellent electrical, chemical stability, mechanical and thermal properties. In this paper, networks of Multi-walled carbon nanotube (MWCNT) materials were investigated as resistive gas sensors for ethanol ($C_2H_5OH$) detection. Sensor films were fabricated by air spray method for the multi-walled CNTs solution on glass substrates. Sensors were characterized by resistance measurements in the sensing system, in order to find the optimum detection properties for the ethanol gas molecular. The film that was sprayed with the MWCNT dispersion for 60 see, was 300 nm thick. And the electric resistivity is $2{\times}10^{-2}\;{\Omega\cdot}cm$. Also, the sensitivity and the linearity of MWVNT sensor for ethanol gas are 0.389 %/sec and 17.541 %/FS, respectively. The MWCNT film was excellent in the response for the ethanol gas molecules and its reaction speed was very fast, which could be using as ethanol gas sensor. The conductance of the fabricated sensors decreases when the sensors are exposed to ethanol gas.

• 한국전기전자재료학회논문지
• /
• 제26권4호
• /
• pp.325-329
• /
• 2013

Carbon nanotubes(CNT) have excellent electrical, chemical stability and mechanical properties. These can be used in a variety of fields. MWCNT are extremely sensitive for minute changes in the ambient gas, namely, their sensing properties varies greatly with the absorption of gas such as NOx and $H_2$. We investigate the electrical properties of CNTs and make a NOx gas sensor based on Multi-walled carbon nanotubes (MWCNT) materials. We obtained the NOx gas sensor of MWCNT based on P-type Si wafer that has the resistivity of $1.667{\times}10^{-1}[{\Omega}{\cdot}cm]$. We knew that the sensitivity of sensor decreased with increasing of NOx gas concentration. And the sensitivity of sensor shows the largest value at $20^{\circ}C$. The sensitivity of sensor decrease with increasing the temperature. Also absorption energy of NOx gas molecule on the MWCNT surface decreases with increasing concentration of NOx gas.

• 전기화학회지
• /
• 제12권3호
• /
• pp.282-286
• /
• 2009

MWNT(CNTs)를 지지체로 촉매를 합성하고 특성평가를 진행하였다. $Pt/Au/TiO_2$는 CNTs(cabon 나노 튜브) 탄소 지지체에 첨가되어 직접 메탄올 연료 전지의 성능을 개선하였다. XRD와 SEM을 통해 아나타제 $TiO_2$와 Pt/Au를 확인하였고 각각의 입자 사이즈는 200 nm와 20${\sim}$25 nm 이다. 혼성 촉매의 활성은 CV를 통해 측정되었으며 제조된 촉매는 연료전지 이용에 유망하다.