• Journal of The Korean Astronomical Society
• /
• v.29 no.1
• /
• pp.53-62
• /
• 1996

31 white dwarfs in 10 open clusters are examined, and their maximum mass and the upper mass limit of their progenitors are obtained as $1.22\pm0.02M_{\bigodot}\;and\;7.2\pm0.4M_{\bigodot}$ respectively, suggesting that the upper mass limit of white dwarfs is less than 8M_{\bigodot}$ The final mass of white dwarfs shows no clear correlation with the initial mass of their progenitors, and it is found that a deficient gap of initial mass exists between $\~4\;and\;~5.2M_{\bigodot}$. This gap seems to correspond to the mass range for carbon detonation or deflagration. The total expected numbers of white dwarfs are $11\~22$ in Hyades with 7 known white dwarfs and 17 in Praesepe with 8 known white dwarfs. These known white dwrfs are all younger than the others in both clusters. But one known white dwarf in Pleiades is older one among $2\~3$ expected white dwarfs.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.1
• /
• pp.103-106
• /
• 2005

In order to investigate the catalytic mechanism for the growth of carbon nanotubes (CNTs), a comprehensive study was conducted using carbon materials synthesized at 680 ${^{\circ}C}$ with a gas mixture of CO-H$_2$ after reduction at 800 ${^{\circ}C}$ by H$_2$ gas from iron oxide, and metal Pt. The resulting material was observed by scanning electron microscopy (SEM) and X-ray diffraction patterns (XRD) after a variety of reaction times. The carbon materials synthesized by metal Pt were little affected by reaction time and the sintered particles did not form CNTs. Xray analysis revealed that metal Fe was completely converted to iron carbide (Fe$_3$C) without Fe peaks in the early stage. After 5 min, iron carbide (Fe$_3$C) and carbon (C) phases were observed at the beginning of CNTs growth. It was found that the intensity of the carbon(C) peak gradually increased with the continuous growth of CNTs as reaction time increases. It was also found that the catalyst of growth of CNTs was metal carbide.

• Composites Research
• /
• v.19 no.2
• /
• pp.7-12
• /
• 2006

Graphite particle/carbon fiber hybrid conductive polymer composites were fabricated by the compression molding technique. Graphite particles were mixed with an epoxy resin to impart the electrical conductivity in the composite materials. In this study, graphite reinforced conductive polymer composites with high filler loadings were manufactured to accomplish high electrical conductivity above 100S/cm. Graphite particles were the main filler to increase the electrical conductivity of composites by direct contact between graphite particles. While high filler loadings are needed to attain good electrical conductivity, the composites becomes brittle. So carbon fiber was added to compensate weakened mechanical property. With increasing the carbon fiber loading ratio, the electrical conductivity gradually decreased because non-conducting regions were generated in the carbon fiber cluster among carbon fibers, while the flexural strength increased. In the case of carbon fiber 20wt.% of the total system, the electrical conductivity decreased 27%, whereas the flexural strength increased 12%.

• Carbon letters
• /
• v.9 no.2
• /
• pp.105-107
• /
• 2008

In this work, we employed an electroless nickel plating on glass fibers in order to enhance the electric conductivity of fibers. And the effects of metal content and plating time on the conductivity of fibers were investigated. From the results, island-like metal clusters were found on the fiber surfaces in initial plating state, and perfect metallic layers were observed after 10 min of plating time. The thickness of metallic layers on fiber surfaces was proportion to plating time, and the electric conductivity showed similar trends. The nickel cluster sizes on fibers decreased with increasing plating time, indicating that surface energetics of the fibers could become more homogeneous and make well-packed metallic layers, resulting in the high conductivity of Ni/glass fibers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.69-69
• /
• 2010

Carbon nano tubes (CNTs) have been attractive candidates for fundamental research studies due to their outstanding physical and chemical properties. High thermal and chemical stability and large surface area make CNTs an ideal platform for many nano materials systems. Several applications such as Several applications were proposed for CNTs many of which are concerned with conductive or high strength composites make them excellent candidates for a variety of energy conversion and storage technologies.

• The Journal of Economics, Marketing and Management
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2016

The purpose of this paper is to discuss the methodology of optimizing delivery route scheduling using a capacity integer linear programming problem model developed to a previous case study. The methodology suggests a two-stage decision: the first, automatic, where the manager will obtain guidance generated by the solution of the linear programming model, later they could use post-optimization techniques to fine tune to the best operational solution. This study has the goal to reduce the size of service companies' ground transportation fleets, aiming not only to reduce costs and increase competitive advantages but also to lower levels of air pollution and its consequences, traffic and, therefore, the levels of carbon dioxide, allowing for a reduction in envir onmental disasters.

• Korean Journal of Microbiology
• /
• v.52 no.3
• /
• pp.298-305
• /
• 2016

Previously our laboratory showed that Pseudomonas alkylphenolica KL28 possesses two different lap and pcu gene clusters for p-cresol catabolism. In this study, additional gene cluster (pchACXF-pcaHG-orf4-pcaBC) has been identified to encode enzymes necessary for catabolism of p-cresol to ${\beta}$-carboxy-cis,cis-muconate. This gene cluster showed almost identical nucleotide sequence homologies to those in the plasmid of Pseudomonas putida NCIMB 9866 and 9869, British origins, indicating the possibility of a horizontal gene transfer. Through mutagenesis of each gene cluster and gfp-based promoter reporter assays, it has been shown that the three gene clusters are functionally operated and pch genes are induced by p-cresol. Furthermore, the pcu gene cluster of the three was shown to be dominantly expressed in utilization of p-cresol. Mutation of the pcu gene was defective in aerial structure formation under p-cresol vapor, indicating the utilization rate of carbon source is one of key elements for the multicellular development of this strain.

• Korean Journal of Materials Research
• /
• v.26 no.6
• /
• pp.298-305
• /
• 2016

In this work, recent progress on graphene/metal oxide composites as advanced materials for $HgCl_2$ and $CO_2$ capture was investigated. Density Functional Theory calculations were used to understand the effects of temperature on the adsorption ability of $HgCl_2$ and water vapor on $CO_2$ adsorption on CaO (001) with reinforced carbon-based nanostructures using B3LYP functional. Understanding the mechanism by which mercury and $CO_2$ adsorb on graphene/CaO (g-CaO) is crucial to the design and fabrication of effective capture technologies. The results obtained from the optimized geometries and frequencies of the proposed cluster site structures predicted that with respect to molecular binding the system possesses unusually large $HgCl_2$ ($0.1-0.4HgCl_2g/g$ sorbent) and $CO_2$ ($0.2-0.6CO_2g/g$ sorbent) uptake capacities. The $HgCl_2$ and $CO_2$ were found to be stable on the surface as a result of the topology and a strong interaction with the g-CaO system; these results strongly suggest the potential of CaO-doped carbon materials for $HgCl_2$ and $CO_2$ capture applications, the functional gives reliable answers compared to available experimental data.

• Smart Structures and Systems
• /
• v.19 no.2
• /
• pp.127-136
• /
• 2017

Fiber reinforced polymer (FRP) has received widespread attention in the field of civil engineering because of its superior durability and corrosion resistance. This article presents the damage mechanisms of a novelty composite called carbon nanofiber modified flax fiber polymer (CNF-modified FFRP). The ability of acoustic emission (AE) to detect damage evolution for different configurations of specimens under uniaxial tension was examined, and some useful AE characteristic parameters were obtained. Test results shows that the mechanical properties of modified composites are associated with the CNF content and the evenness of CNF dispersed in the epoxy matrix. Various damage mechanisms was established by means of scanning electron microscope images. The fuzzy c-means clustering were proposed to classify AE events into groups representing different generation mechanisms. The classifiers are constructed using the traditional AE features -- six parameters from each burst. Amplitude and peak-frequency were selected as the best cluster-definition features from these AE parameters. After comprehensive comparison, a correlation between these AE events classes and the damage mechanisms observed was proposed.

• Journal of Powder Materials
• /
• v.16 no.1
• /
• pp.43-49
• /
• 2009

Titanium carbides are widely used for cutting tools and grinding wheels, because of their superior physical properties such as high melting temperature, high hardness, high wear resistance, good thermal conductivity and excellent thermal shock resistance. The common synthesizing method for the titanium carbide powders is carbo-thermal reduction from the mixtures of titanium oxide($TiO_2$) and carbon black. The purpose of the present research is to fabricate nano TiC powders using titanium salt and titanium hydride by the mechanochemical process(MCP). The initial elements used in this experiment are liquid $TiCl_4$(99.9%), $TiH_2$(99.9%) and active carbon(<$32{\mu}m$, 99.9%). Mg powders were added to the $TiCl_4$ solution in order to induce the reaction with Cl-. The weight ratios of the carbon and Mg powders were theoretically calculated. The TiC and $MgCl_2$ powders were milled in the planetary milling jar for 10 hours. The 40 nm TiC powders were fabricated by wet milling for 4 hours from the $TiCl_4$+C+Mg solution, and 300 nm TiC particles were obtained by using titanium hydride.