• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1060-1066
• /
• 1997

In this paper, the effects of La addition of PLZT thin film prepared by sol-gel method on the capacitor characteristics are investigated for gigabit generation DRAM applications. The addition of La on the PLZT capacitor results in a trade-off between charge storage density(Qc') and leakage current density(Jl). As La content increases, Qc' and permeability(εr) at 0V are reduced while Jl is significantly decreased. It is demonstrated that 5% La doping of PZT can substantially reduce Jl and also improve resistance to fatigue while incurring only minimal degradation of Qc'. Very low leakage current density (5×10-7 A/㎠ even at 125℃) and high charge storage density (100fC/㎛2) under VDD/2=1V conditions are achieved using 5% La doped PZT thin films for gigabit DRAM capacitor dielectrics. In addition, the fatigue and TDDB measurements indicate good reliability of the PLZT capacitors.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.2
• /
• pp.150-156
• /
• 2004

Although permanent magnet single phase synchronous motor which starts and runs through single phase voltage source has high efficiency, it is difficult to determine the rotating direction. In this paper, the starting characteristics of the capacitor-run single phase synchronous motor has been studied. The stator has same structure with the capacitor-run single phase induction motor, however the rotor consists of permanent magnet. In this case, the starting conditions according to the rotor and stator conditions are determined and the direction of the motor can be determined. From these results, it is desired that the proposed motor can be applied to the loads like the fans which has low starting torque.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.6
• /
• pp.2697-2701
• /
• 2012

The yield of OTP devices using anti-fuse MOS capacitor have been affected by the input resistance, the size of the pass transistor and the read transistor, and the readout voltage of programed cell. To investigate the element which gives an effect to yield, we analyze the full map data of the resistance characterization of OTP device and those data in a various experimental condition. As a result, we got the optimum conditions which is necessary to the yield improvement. The optimum conditions are as follows: Input resistance is 50 ohms, the channel length of pass transistor is 10um, read voltage is 2.8 volt, respectively.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.4
• /
• pp.325-331
• /
• 2022

This study proposes a design method that minimizes a conduction loss of LCC resonant converter under rated condition. Through a simplified analysis of the waveform of the resonant current, the power transfer section and RMS value of the resonant current was analyzed mathematically and graphically. Based on this analysis, the design method that minimizes the RMS value of the resonant current is proposed. To demonstrate this method, this study designed a 7.5 kW (100 V, 75 A) capacitor charger based on LCC resonant converter and the design parameters were chosen according to the process of the design method. Then, the capacitor charger was implemented. An experiment was conducted to measure efficiency while satisfying design specifications under rated conditions. This design method was verified to be effective by achieving 97.7% maximum efficiency and design specifications under rated conditions.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.5
• /
• pp.1012-1020
• /
• 2013

In this work, Self-adaptive Differential Evolutionary (SaDE) algorithm is proposed to solve Optimal Location and Size of Capacitor (OLSC) problem in radial distribution networks. To obtain the SaDE algorithm, two improvements have been applied on control parameters of mutation and crossover operators. To expand the study, three load conditions have been considered, i.e., constant, varying and effective loads. Objective function is introduced for the load conditions. The annual cost is fitness of problem, in addition to this cost, CPU time, voltage profile, active power loss and total installed capacitor banks and their related costs have been used for comparisons. To confirm the ability of each improvements of SaDE, the improvements are studied both in separate and simultaneous conditions. To verify the effectiveness of the proposed algorithm, it is tested on IEEE 10-bus and 34-bus radial distribution networks and compared with other approaches.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.4
• /
• pp.186-191
• /
• 2012

DC Bus Electrolytic capacitors have been widely used in power conversion system because they can achieve high capacitance and voltage ratings with volumetric efficiency and low cost. This type of capacitors have been traditionally used for filtering, voltage smoothing, by-pass and other many applications in power conversion circuits requiring a cost effective and volumetric efficiency components. Unfortunately, electrolytic capacitors are some of the weakest components in power electronic converter. Many papers have proposed different methods or algorithms to determinate the ESR and/or capacitance C for fault diagnosis of the electrolytic capacitor. However, both ESR and C vary with frequency and temperature. Accurate knowledge of both values at the capacitors operating conditions is essential to achieve the best reference data of fault judgement. According to parameter analysis, the capacitance increases with temperature and the ESR decreases. Higher frequencies make the ESR and C to decrease. Analysis results show that the proposed electrolytic capacitor parameter estimation technique can be applied to reference signal of capacitor diagnosis systems successfully.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_2
• /
• pp.1117-1125
• /
• 2023

The DC part of the DC microgrid power conversion system uses capacitors for buffers of charge and discharge energy for smoothing voltage and plays important roles such as high frequency component absorption, power balancing, and voltage ripple reduction. The capacitor uses an aluminum electrolytic capacitor, which has advantages of capacity, low price, and relatively fast charging/discharging characteristics. Aluminum electrolytic capacitors(AEC) have previous advantages, but over time, the capacity of the capacitors decreases due to deterioration and an increase in internal temperature, resulting in a decrease in use efficiency or an accident such as steam extraction due to electrolyte evaporation. It is necessary to take measures to prevent accidents because the failure diagnosis and detection of such capacitors are a very important part of the long-term operation, safety of use, and reliability of the power conversion system because the failure of the capacitor leads to not only a single problem but also a short circuit accident of the power conversion system.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.941-947
• /
• 2018

In general, capacitors have a large influence on the life of the system due to frequent charging and discharging. In this paper, we analyze the cause of the core failure of high voltage, high current HVDC sub-module film capacitor and analyze the precautions of the capacitor design and manufacturing process. First, the cause of the fault, the failure mode, and the effect are analyzed through the FMEA of the capacitor. To quantitatively evaluate the causes and effects of faults that have the greatest effect on the failure of a capacitor, a fault tree for the capacitor is presented and the failure rate is analyzed according to the design parameters and the driving conditions. It is verified that the main cause of capacitor failure is the capacitance change, and it is necessary to minimize the temperature rise, corona occurrence, electrode expansion, and insulation distance decrease during capacitor design and manufacturing process in order to reduce the failure rate of the capacitor.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.100-108
• /
• 2016

This paper presents a simple high efficiency full-bridge DC-DC converter using a series resonant capacitor. The proposed converter achieves the zero voltage switching of the primary switches under a wide range of load conditions and reduces the high circulating current in the freewheeling mode using the leakage resonant inductance and the series resonant capacitor. Thus, the proposed converter overcomes the drawbacks of the conventional full-bridge DC-DC converter and improves its overall system efficiency. Its structure is simplified by using the leakage inductance of the transformer as the resonant inductance and omitting the DC output filter inductance. Also it can operate over a wide range of input voltages. In this paper, the operational principle, analysis and design example are described in detail. Finally, the experimental results from a 650W (24V/27A) prototype are demonstrated to confirm the operation, validity and features of the proposed converter.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.5
• /
• pp.71-78
• /
• 2012

This paper presents a digital control solution to process capacitor current feedback of high performance single-phase UPS for non-linear loads. In all UPS the goal is to maintain the desired output voltage waveform and RMS value over all unknown load conditions and transient response. The proposed UPS uses instantaneous load voltage and filter capacitor current feedback, which is based on the double regulation loop such as the outer voltage control loop and inner current control loop. The proposed DSP-based digital-controlled PWM inverter system has fast dynamic response and low total harmonic distortion (THD) for nonlinear load. The control system was implemented on a 32bit Floating-point DSP controller TMS320C32 and tested on a 5[KVA] IGBT based inverter switching at 11[Khz]. The validity of the proposed scheme is investigated through simulation and experimental results.