• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2015년도 전력전자학술대회 논문집
• /
• pp.367-368
• /
• 2015

This paper introduces a shunt active power filter with a small DC bus capacitor by adding additional low-pass filter (LPF). The DC link voltage fluctuation is impressively suppressed with a small value in spite of the low value of DC-link capacitor under the steady-state condition. Consequently, the cost and volume of power converter are significantly reduced thanks to the reduced value of DC-bus capacitor. On the other hand, an indirect control strategy is used to maintain grid-side current when non-linear loads are connected to the system. By using proportional-integral (PI) and modified repetitive controller (RC) in dq0 frame, the calculation time is greatly decreased by 6 times compared with the conventional RC, and the number of measurement devices is also minimized. As a result, the acquired total harmonic distortion (THD) is lower than 2% regardless of the load conditions. Simulation results are carried out in order to verify the effectiveness of the proposed control strategy.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권2호
• /
• pp.176-183
• /
• 2014

Three-phase four-wire distribution systems are used for both three-phase three-wire loads and single-phase two-wire consumer appliances in South Korea, Myanmar and other countries. Unbalanced load conditions frequently occur in these distribution systems. These unbalanced load conditions cause unbalanced voltages for three-phase and single-phase loads, and increase the loss in the distribution transformer. In this paper, we propose constant DC capacitor voltage control based strategy for the active load balancer (ALB) in the three-phase four-wire distribution systems. Constant DC capacitor voltage control is always used in active power line conditioners. The proposed control strategy does not require any computation blocks of the active and reactive currents on the distribution systems. Balanced source-side currents with a unity power factor are obtained without any calculation block of the unbalanced active and reactive components on the load side. The basic principle of the constant DC capacitor voltage control based strategy for the ALB is discussed in detail and then confirmed by both digital computer simulations using PSIM software and prototype experimental model. Simulation and experimental results demonstrate that the proposed control strategy for the ALB can balance the source currents with a unity power factor in the three-phase four-wire distribution systems.

• 전기학회논문지P
• /
• 제66권4호
• /
• pp.213-218
• /
• 2017

The DC electrolytic capacitor for DC-link of power converter is widely used in various power electronic circuits and system application. Its functions include, DC Bus voltage stabilization, conduction of ripple current due to switching events, voltage smoothing, etc. Unfortunately, DC electrolytic capacitors are some of the weakest components in power electronics converters. Many papers have proposed different algorithms or diagnosis method to determinate the ESR and tan ${\delta}$ capacitance C for fault alarm system of the electrolytic capacitor. However, both ESR vary with frequency and temperature. Accurate knowledge of both parameters at the capacitors operating conditions is essential to achieve the best reference data of fault alarm. According to parameter analysis, the capacitance increases with temperature and the initial ESR decreases. Higher frequencies make the reference ESR with the initial ESRo value to decrease. Analysis results show that the proposed DC Bus electrolytic capacitor reference ESR model setting technique can be applied to advanced reference signal of capacitor diagnosis systems successfully.

• 한국세라믹학회지
• /
• 제40권7호
• /
• pp.644-651
• /
• 2003

첨가물의 형태가 X7R용 MLCC 유전 원료의 전기적 특성 및 미세구조에 미치는 영향을 평가하였다. Glass frit 및 산화물 형태로 제조된 첨가물을 분말 공정 조건을 달리하여 동일한 주조성에 첨가하였다. 미세구조 및 유전특성을 측정한 결과, glass 층에 dopant의 농도 구배가 존재하는 조성이 유전 특성이 가장 우수하였다. 최적 조성을 MLCC로 제작하여 유전 특성을 측정하였으며, X7R 제반 조건을 만족하였다.

• 한국생산제조학회지
• /
• 제24권6호
• /
• pp.653-659
• /
• 2015

The aim of this study is to develop a technique for the accelerated life test of the capacitor in a propulsion control device of a traction inverter used for a high-speed train. Using this technique, the accelerated life test can possibly estimate the life cycle of a capacitor under various temperature conditions and irregularly applied voltage. The accelerated life test is conducted for the capacitor of the traction inverter. The common proceedings of this test are selection of failure mechanism, determination of accelerated stress, range determination of the accelerated stress, determination of the test condition, and distribution and determination of the sample. From this result, the continuous applied voltage was not considered for the acceleration factors anymore. Therefore, the final result having an acceleration factor of 9.4 (= 13,626/1,445) was observed. Furthermore, the life-shortening acceleration effect for the irregular applied voltage condition can be applied to various situations.

• 한국산학기술학회논문지
• /
• 제19권4호
• /
• pp.117-122
• /
• 2018

대용량 3상 시스템 에어컨은 최근 들어 소비 전력 저감을 위해 인버터 회로를 포함하고 있다. 인버터 회로는 교류를 다이오드를 통해 정류하고 DC-link 전원부 콘덴서에 의해 평활된 직류를 사용한다. 이 때 평활에 사용되는 DC-link 전원부 콘덴서는 전압 리플, 전류 리플 조건을 만족하기 위해 전해 콘덴서가 일반적으로 사용된다. 콘덴서의 용량을 줄이게 되면 회로부의 크기 및 무게, 비용을 줄일 수 있게 된다. 본 논문에서는 최소점 추정 PPL(Phase Locked Loop) 위상 제어와 평균 전압 d축 전류제어 기법을 조합하여 입력 리플 전류를 약 90% 저감하는 알고리즘을 제안한다. 입력 리플 전류의 감소로 인해 DC-link 콘덴서의 전류 리플도 감소하므로 콘덴서의 용량을 줄일 수 있지만 전해 콘덴서의 경우 등가 직렬 저항(ESR : Equivalent Series Resistance)이 크기 때문에 발열로 인한 수명이 한계를 가진다. 본 논문에서는 전해 콘덴서 대신 DC-link 단에 전류 리플을 고려한 필름 콘덴서를 선정하는 방법을 제안한다. 필름 콘데서의 정전 용량 선정, 내압 선정, RMS(Root Mean Square) 전류 용량, RMS 전류 주파수 해석을 고려해 콘덴서의 용량을 선정할 경우 1680uF의 전해 콘덴서를 20uF로 용량을 낮추어 설계함으로써 전원부 콘덴서의 크기 및 무게, 비용을 줄였으며 전동기 구동을 통해 동작을 확인하였다.

• 전기학회논문지
• /
• 제58권8호
• /
• pp.1457-1462
• /
• 2009

This paper proposes a compensating algorithm for the secondary voltage of a coupling capacitor voltage transformer (CCVT) in the time domain by considering the hysteresis characteristics of the core. The proposed algorithm estimates the three error terms i.e. the voltage across the secondary winding parameters, the voltage across the primary winding parameters, and the voltage across the capacitor and the tuning reactor. These three terms are added to the measured secondary voltage to obtain the correct voltage. The algorithm reduces the errors of the CCVT significantly both in the steady state and during a fault. The performance of the algorithm is verified under the various fault conditions by varying the fault distance, the fault inception angle, and the fault impedance with the EMTP generated data. Test results clearly indicate that the algorithm can increase the accuracy of a CCVT significantly under the fault conditions as well as in the steady state. The algorithm helps improve the performance of a protection relay or a metering device.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권4호
• /
• pp.336-343
• /
• 1996

We have studied the preparation and the properties of $Ba_{1-x}$Sr$_{x}$TiO$_{3}$(BST) thin films by using the sol-gel method. Through the comparison of the effects of various solvents and additives in making solutions, we establish the production method of the stable solution which generates the high quality of BST film. We also set up the heat-treatment conditions for depositing the BST thin film through the TGA and XRD analyses. Through the comparison of the surface conditions of BST films deposited on Pt/Ta/SiO$_{2}$/Si and Pt/Ti/SiO$_{2}$/Si substrates, we find that Ta is more efficient diffusion barrier of Si than Ti so that Ta layer prevents the formation of hillocks. We fabricate the planar type capacitor and measure the dielectric properties of the BST thin film deposited on the Pt/Ta/SiO$_{2}$/Si substrate. Dielectric constant and dielectric loss tangent at 1V, 10kHz, and leakage current density at 3V of the BST thin film are 339, 0.052 and 13.3.mu.A/cm$^{2}$, respectively.ely.

• 대한전기학회논문지
• /
• 제43권3호
• /
• pp.381-387
• /
• 1994

In this paper, we found the improved SPICE heat transfer modeling of impulsed magnetizing fixture system and investigated temperature characteristics using the proposed model. As the detailed thermal characteristics of magnetizing fixture can be obtained, the efficient design of the impulsed magnetizing fixture which produce desired magnet will be possible using our heat transfer modeling. The knowledge of the temperature of the magnetizing fixture is very important of forecast the characteristics of the magnetizing fixture which produce desired magnet will be possible using our heat transfer modeling. The knowledge of the temperature of the magnetizing fixture is very important to forecast the characteristics of the magnetizing circuits under different conditions. The capacitor voltage was not raised above 810[V] to protect the magnetizing fixture from excessive heating. The purpose of this work is to compute the temperature increasing for different magnetizing conditions. The method uses multi-lumped model with equivalent thermal resistance and thermal capacitance. The reliable results are obtained by using iron core fixture (stator magnet of air cleaner DC motor) coupled to a low-voltage magnetizer(charging voltage : 1000[V], capacitor : 3825[$\mu$F]. The modeling and experimental results are in close aggrement.

• Korean Chemical Engineering Research
• /
• 제44권6호
• /
• pp.614-622
• /
• 2006

질산망간수용액의 열분해에 의한 이산화망간 적용 $Ta/Ta_2O_5/MnO_2$ 커패시터의 특성 연구를 수행하였다. 질산망간수용액의 TG/DSC 분석을 통해 약 $230{\sim}250^{\circ}C$ 범위에서 단일상의 이산화망간이 생성되었다. 열분해 온도, 질산망간수용액의 농도, 열분해 회수를 이산화망간 고체 전해질 생성의 기초 변수로 선정하고 이에 따른 커패시터 특성을 평가하였다. 최적 조성을 기준으로 복사열분해 방식이 대류열분해 방식에 비하여 우수한 특성을 발휘하였다. 이는 복사열분해에 의해 상대적으로 구형의 작은 입자 상태의 이산화망간 입자들이 생성되고 이를 통해 미세 다공성 구조의 커패시터 소결체 내부에 균일하고 치밀한 이산화망간 고체전해질 층이 생성되는 것에서 기인하는 결과임을 확인하였다.