• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1060-1066
• /
• 1997

In this paper, the effects of La addition of PLZT thin film prepared by sol-gel method on the capacitor characteristics are investigated for gigabit generation DRAM applications. The addition of La on the PLZT capacitor results in a trade-off between charge storage density(Qc') and leakage current density(Jl). As La content increases, Qc' and permeability(εr) at 0V are reduced while Jl is significantly decreased. It is demonstrated that 5% La doping of PZT can substantially reduce Jl and also improve resistance to fatigue while incurring only minimal degradation of Qc'. Very low leakage current density (5×10-7 A/㎠ even at 125℃) and high charge storage density (100fC/㎛2) under VDD/2=1V conditions are achieved using 5% La doped PZT thin films for gigabit DRAM capacitor dielectrics. In addition, the fatigue and TDDB measurements indicate good reliability of the PLZT capacitors.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.277-279
• /
• 2008

In this paper, a novel active boost converter for SR drive is proposed. An active capacitor circuit is added in the front-end. Based on this active capacitor network, when boost switch turns off, this network seems as passive capacitor network. And the voltage of boost capacitor can keep balance with dc-link voltage automatically. In the capacitor network, discharging voltage is general dc-link voltage in parallel-connected capacitors; charging voltage is double dc-link voltage in series-connected capacitors. When boost switch turns on, two capacitors are connected in series, and discharging voltage is up to double dc-link voltage. So the fast excitation current can be obtained from this mode. Profit from fast excitation and fast demagnetization mode, the performance and output power can be improved. Some computer simulations are done to verify the performance of proposed converter.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.1
• /
• pp.36-40
• /
• 2008

Most of the low-voltage feeder are designed with approximately balanced and connected at the three phase four wire systems. However, Most of the power distribution systems' load which is composed of single or three phase are unbalanced by generating load unbalance. Unbalanced current will draw a highly unbalanced voltage. The power factor of an induction motor at rated operation is between 25 and 90%, depending on the size and speed of the motor. However, many induction motors operate below the nominal rating, resulting in poor power factor. This condition needs power factor improvement. Addition of power capacitor at the motor terminal may draw to stress due to voltage unbalance. This paper presents operation characteristics on steady states of a three-phase induction motor under unbalanced voltages with power capacitor. The existence of voltage unbalance have an effect on stress of power capacitor.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2089-2091
• /
• 2000

Pulsed power systems consist of a capacitor bank, an isolated high-voltage charging power-supply, high-current bus-work for charging and discharging and a control system. In such pulsed power systems, the operating-lifetime of the capacitors is closely dependent on the voltage reversal. Hence, most capacitor-discharging systems includes crowbar circuits. The crowbar circuit prevents the capacitor recharging with reverse voltage. Usually it consists of crowbar resistors and high pulse-current diode-stacks connected in series. The requirements for the diode-stacks are fast-recovery time and high-voltage and large-current ratings, which results in the high cost of the pulsed-power system. This paper presents a protection scheme of a charging and discharging system of a 500kJ capacitor bank using a low-cost crowbar circuit and safety-fuses.

• Journal of Applied Reliability
• /
• v.12 no.1
• /
• pp.25-33
• /
• 2012

As to display products are made slim, the diameter of aluminum electrolytic capacitor is smaller and the length is longer to be fitted in. These small diameter and long length are pointed as the disadvantageous design factors of the capacitor's life cycle. So, the most electronic makers want to use proven capacitors (or well-known) to secure reliability of the electric products. In this study, we carried out the comparison analysis with two domestic capacitors and one foreign made capacitor. We designated separators, rubber breather and debris as the main factors that effect on the lifetime of capacitors. From the comparison results, we suggested the improvement points of the aluminum electrolytic capacitor.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.315-319
• /
• 2011

A switched-capacitor cyclic DAC scheme with mismatch compensation of capacitors is designed. In cyclic DAC, a little error between two capacitors is accumulated every cycle. As a result, the accumulated error influences the final analog output which is wrong data. Therefore, a mismatch compensation technique was proposed and the error can be effectively reduced, which alleviates the matching requirement. In order to verify the operation of the proposed DAC, an 8-bit switched-capacitor cyclic DAC is designed through HSPICE simulation and implemented through magna 0.18um standard CMOS process.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.9
• /
• pp.1283-1288
• /
• 2012

This paper presents speed control characteristics of capacitor-run SPIM(Single Phase Induction Motor) using TRIAC for comparing and analyzing four kinds of voltage control methods such as supply voltage control, main winding voltage control, auxiliary winding voltage control and auxiliary winding voltage control without starting capacitor. The computer simulations were performed using MATLAB Simulink to show control characteristics of four voltage control methods. And their control characteristics were conformed by experiments for capacitor-run 90W SPIM as a sample motor. The results of simulations and experiments show that supply voltage control method has fast dynamic response characteristics and main winding voltage control method has higher power efficiency and can be implemented at lower system cost.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.55-56
• /
• 2012

In general, a power decoupling method using electrolytic capacitor is used to solve a problem that appears 120[Hz] ripple of grid at the PV module output. But electrolytic capacitor has a effect on the short lifetime and low reliability of PV system. Therefore, studies which replace the large electrolytic capacitor with small film capacitor have been researched in resent years. This paper proposes flyback inverter which can be replaced with film capacitor by connecting the circuit implementing zero voltage switching in PV side. The proposed system is validated by PSIM simulation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.57-58
• /
• 2005

The properties such as capacitance and resonant frequency are important in embedded capacitors. Accurate equivalent model is required to find these properties of embedded capacitor. In this paper, we investigate to analyze the properties of high-K embedded capacitor which was fabricated by Low Temperature Co-fired Ceramic (LTCC). Modeling based on partial element equivalent circuit (PEEC) method is performed using HSPICE circuit simulation. This modeling methodology can provide the good inspection of embedded capacitor to device engineer.

• Korean Journal of Metals and Materials
• /
• v.48 no.4
• /
• pp.326-334
• /
• 2010

Porous and net-shaped tantalum powder for a capacitor was formulated in a SHS (self-propagating high-temperature synthesis) process. However, this powder, which has weak strength among its particles and low flow ability, cannot be used for a capacitor. Therefore, this powder was sintered in a high-vacuum furnace to increase agglomeration to improve the flow ability, bonding strength among the particles, and shrinkage during pellet sintering. Finally, it was deoxidated with 2 wt% Mg powder to remove the increased surface oxygen that arose during the sintering process. The final product was analyzed in terms of its chemical and physical properties and was compared with a commercial powder used by a capacitor manufacturer.