• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.434-436
• /
• 1996

This paper investigates the optimal design of an electronic ballast of half bridge inverter type in consideration of the variation of ambient temperatures for a 15[W] triple-type compact fluorescent lamp. The performances of electronic ballasts under different values or the capacitance ratio in the resonant tank circuit are compared with each other in the practical temperature range between 15[$^{\circ}C$] and 35[$^{\circ}C$] to determine its optimum value. As a result, the optimum value is found to be such that $C_1/C_2=10$ at which value starting of the lamp is most stable and light output reaches its maximum value with lowest variation.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제49권6호
• /
• pp.316-321
• /
• 2000

In this paper, we proposed MBDD(Modified Binary Decision Diagram) as a multi-level logic synthesis method and a vertex of MBDD to NMOS transistors matching. A vertex in MBDD is matched to a set of NMOS transistors. MBDD structure can be achieved through transformation steps from BDD structure. MBDD can represent the same function with less vertices less number of NMOS transistors, consequently capacitance of the circuit can be reduced. Thus the power dissipation can be reduced. We applied MBDD to a full odder and a 4-2compressor. Comparing the 4-2compressor block with other synthesis logic, 31.2% reduction and 19.9% reduction was achieved in numbers of transistors and power dissipation respectively. In this simulation we used 0.8 ${\mu}{\textrm}{m}$ fabrication parameters.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2009년도 정보통신설비 학술대회
• /
• pp.305-308
• /
• 2009

This paper presents the design and analysis of RF Front End for Wireless Heartbeat measurement System. In this work LNA, an inductor connected at the gate of the cascode transistor and capacitive cross-coupling are strategically combined to reduce the noise and the nonlinearity influences of the cascode transistors in a differential LNA. The Mixer is implemented by using the Gilbert-type configuration, cross pmos injection technique and the resonating technique for the tail capacitance. The resulting LNA achieves 1.26 dB NF, better than 1.88dB NF Typical Also Mixer resulting achieves 9.8dB at 100KHz.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 정기총회 및 추계학술대회 논문집 학회본부
• /
• pp.82-84
• /
• 1993

A method for simulating general characteristics and temperature characteristics of magnetizing fixture coil of the capacitor discharge impulse magnetizer-magnetizing fixture system using SPICE is presented. This method has been developed which can aid the design, understanding and inexpensive, time-saving of magnetizing circuit. As the detailed characteristics of magnetizing circuit can be obtained, the efficient design of the magnetizing circuit which produce desired magnet will be possible using our SPICE modeling. Especially, The knowledge of the temperature of the magnetizing fixture is very important to forecast the characteristics of the magnetizing circuits tinder different conditions. The capacitor voltage was not raised above 810[V] to protect the magnetizing fixture from excessive heating. The temperature estimation method uses multi-lumped model with equivalent thermal resistance and thermal capacitance.

• 정보학연구
• /
• 제3권1호
• /
• pp.117-124
• /
• 2000

본 논문은 설계 자동화를 위한 저전력 하드웨어 할당 알고리듬을 제안한다. 제안한 알고리듬은 스케줄링의 결과를 입력으로 받아들이고, 각 기능 연산자에 연결된 레지스터 및 연결 구조가 최대한 공유하도록 제어스텝마다 연산과 기억 소자의 상호 연결 관계를 고려하여 기능 연산자, 연결 구조 및 레지스터 할당한다. 또한 자원의 수를 최대로 줄임으로써 할당 과정동안 저전력의 요소인 캐패시턴스를 동시에 줄인다. 제안된 알고리듬은 비교 실험을 통하여 기존의 저전력을 고려하지 않은 방식들과 비교함으로서 본 논문의 효율성 을 보인다.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2002년도 종합학술발표회 논문집 Vol.12 No.1
• /
• pp.161-164
• /
• 2002

In this paper, a design technique is introduced for designing a 360-degree linear analog phase shifter at 1.8㎓. Using tunable short-circuit terminated comb-line filters as reactive loads, the circuit gives a very small insertion loss(less than 0.1㏈) and an almost linear phase shifter over the filter bandwidth for the full 360-degree range. We were showed large phase variation with small capacitance variation in the quadrature hybrid coupler using tunable shorted terminated combline filters.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.189-194
• /
• 2001

This paper presents a mew design of an inductive position sensing system with high sensitivity. The designed system consists of the driving coils, position-detecting coils, and closed loop formed magnetic blocks. To obtain high sensitivity we design a symmetric and closed loop type measuring system with small air-gaps. The elements that affect the system characteristics are turn ratio, excitation frequency, air-gap size, capacitance effect, and load resistance. By experimental investigation, the influences of these elements are examined and the system parameters are selected. The sensitivity of the newly designed system is greater than 2800mV/(V mm) and the linearity error is below${\pm}0.01%; in; the; range; of; {\pm}200{\mu}m$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.357-360
• /
• 2003

In this paper, we designed 4.5kV/1.5kA IGCT devices. GCT thyristor has many superior characteristics compared with GTO thyristor, for examples; snubberless turn-off capability, short storage time, high turn-on capability, small turn-off gate charge and low total power loss of the application system containing device and peripheral parts such as anode reactor and snubber capacitance. In this paper we designed GCT thyristor devices, and analyzed static and dynamic characteristics of GCT thyristor depending on the minority carrier lifetime, n-base thickness and doping concentration of n-base region, respectively. Especially, turn-on and turn-off characteristics are very important characteristics for GCT thyristor devices. So, we considered above characteristic for design and analysis of GCT devices.

• 한국공작기계학회논문집
• /
• 제14권5호
• /
• pp.13-20
• /
• 2005

Micro EDM process is generally used for machining microholes, cavities, and three dimensional shapes. For machining micro structures, first of all, micro tool electrode is indispensable and WEDG system is proposed for tool fabrication method. When using WEDG, its machining characteristics are highly affected by many EDM parameters such as applied voltage, current, rotation speed, capacitance, and pulse duration. Therefore, the design of experiment is introduced to fully understand the effect of the EDM parameters on machining tool electrode. And an attempt has been made to develop the mathematical model for predicting the size of the tool electrode by calculating spark distance. The suggested model was verified with experiment and predicted working gap distance is in good accord with the measured value.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2186-2188
• /
• 1999

A high frequency and energy density pulse transformer is a critical component of a high voltage power supply in a traveling wave tube (TWT) amplifier system. In this paper, processes of design, manufacturing, and test of the transformer are discussed. Primary voltage of the transformer is 240 V. The transformer secondary have two outputs which are 4100 V (Helix) and 2050 V (Collector). Total output power is 860 W. Normal operating frequency of the transformer is 10 kHz. In high energy density pulse transformers, temperature rise is a main problem during its operation. From our study, it was found that resonant current due to leakage inductance and stray capacitance was the main cause of temperature rise. This happens because of the inherently high turn-ratio in high voltage transformers. Solutions to reduce stray components are presented.