• Restorative Dentistry and Endodontics
• /
• v.37 no.3
• /
• pp.149-154
• /
• 2012

Objectives: To evaluate the accuracy of the Root ZX in teeth with simulated root perforation in the presence of gel or liquid type endodontic irrigants, such as saline, 5.25% sodium hypochlorite (NaOCl), 2% chlorhexidine liquid, 2% chlorhexidine gel, and RC-Prep, and also to determine the electrical conductivities of these endodontic irrigants. Materials and Methods: A root perforation was simulated on twenty freshly extracted teeth by means of a small perforation made on the proximal surface of the root at 4 mm from the anatomic apex. Root ZX was used to locate root perforation and measure the electronic working lengths. The results obtained were compared with the actual working length (AWL) and the actual location of perforations (AP), allowing tolerances of 0.5 or 1.0 mm. Measurements within these limits were considered as acceptable. Chi-square test or the Fisher's exact test was used to evaluate significance. Electrical conductivities of each irrigant were also measured with an electrical conductivity tester. Results: The accuracies of the Root ZX in perforated teeth were significantly different between liquid types (saline, NaOCl) and gel types (chlorhexidine gel, RC-Prep). The accuracies of electronic working lengths in perforated teeth were higher in gel types than in liquid types. The accuracy in locating root perforation was higher in liquid types than gel types. 5.25% NaOCl had the highest electrical conductivity, whereas 2% chlorhexidine gel and RC-Prep gel had the lowest electrical conductivities among the five irrigants. Conclusions: Different canal irrigants with different electrical conductivities may affect the accuracy of the Root ZX in perforated teeth.

• Restorative Dentistry and Endodontics
• /
• v.41 no.3
• /
• pp.189-195
• /
• 2016

Objectives: A variety of root canal sealers were recently launched to the market. This study evaluated physicochemical properties, biocompatibility, and sealing ability of a newly launched resin-based sealer (Dia-Proseal, Diadent) compared to the existing root canal sealers (AHplus, Dentsply DeTrey and ADseal, Metabiomed). Materials and Methods: The physicochemical properties of the tested sealers including pH, solubility, dimensional change, and radiopacity were evaluated. Biocompatibility was measured using the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay. For microleakage test, single-rooted teeth were instrumented, and obturated with gutta-percha and one of the sealers (n = 10). After immersion in 1% methylene blue solution for 2 weeks, the specimens were split longitudinally. Then, the maximum length of staining was measured. Statistical analysis was performed by one-way analysis of variance followed by Tukey test (p = 0.05). Results: Dia-Proseal showed the highest pH value among the tested sealers (p < 0.05). ADseal showed higher dimensional change compared to AHplus and Dia-Proseal (p < 0.05). The solubility values of AHplus and Dia-Proseal were similar, whereas ADseal had the lowest solubility value (p < 0.05). The flow values of sealer in increasing order were AHplus, DiaProseal, and ADseal (p < 0.05). The radiopacity of AHplus was higher than those of ADseal and Dia-Proseal (p < 0.05). The cell viability of the tested materials was statistically similar throughout the experimental period. There were no significant differences in microleakage values among the tested samples. Conclusions: The present study indicates that Dia-Proseal has acceptable physicochemical properties, biocompatibility, and sealing ability.

• Journal of Korean Society of Forest Science
• /
• v.24 no.1
• /
• pp.53-61
• /
• 1974

Pine forests existing in Hong-do island were examined as regarding such characteristics, tree form, needle length, branch diameter, bark colors, ratio of summer wood to springwood, location and number of resin canal and other measurements. Hong-do island, located the furthest west part of Korea, suports only Pinus densiflora but very few Pinus thunbergii, in fact the present authors could not find any black pine individuals at all through investigation. Checking 14 individual trees of red pine, more than age of 20, of the genetic contamination by black pine, in a certain degree, exist. Here, a very dense foliage type and a very sparse foliage type tree of red pine growing nearby was examined and the unique fact was that each of those type has only one (average number 1.3) accessory resin canal, while other trees have three as minimum or more. The present authors thought this island had not been covered by any Pinus thunbergii but by Pinus densiflora. It was thought that Pinus thunbergii stands grown along the sea-coast of Korean Peninsula are pollen donors to this island.

• Restorative Dentistry and Endodontics
• /
• v.43 no.1
• /
• pp.2.1-2.10
• /
• 2018

Objectives: To determine the effect of size and insertion depth of irrigation needle on the amount of apical extruded debris and the amount of penetration depth of sealer using a confocal laser scanning microscope (CLSM). Materials and Methods: Twenty maxillary premolars were assigned to 2 groups (n = 10), according to the size of needle tip, 28 G or 30 G. Buccal roots of samples were irrigated with respective needle type inserted 1 mm short of the working length (WL), while palatal roots were irrigated with respective needle type inserted 3 mm short of the WL. Prepared teeth were removed from the pre-weighed Eppendorf tubes. Canals were filled with F3 gutta-percha cone and rhodamine B dye-labeled AH 26 sealer. Teeth were transversally sectioned at 1 and 3 mm levels from the apex and observed under a CLSM. Eppendorf tubes were incubated to evaporate the irrigant and were weighed again. The difference between pre- and post-weights was calculated, and statistical evaluation was performed. Results: Inserting needles closer to the apex and using needles with wider diameters were associated with significantly more debris extrusion (p < 0.05). The position of needles and level of sections had statistically significant effects on sealer penetration depth (p < 0.05 for both). Conclusions: Following preparation, inserting narrower needles compatible with the final apical diameter of the prepared root canal at 3 mm short of WL during final irrigation might prevent debris extrusion and improve sealer penetration in the apical third.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.38 no.4
• /
• pp.435-440
• /
• 2011

Maxillary canine impaction is a common eruption problem in children. Impaction frequently involves further complications such as root resorption of adjacent teeth, cyst formation and migration of the neighboring teeth, etc. Various treatment modalities include extraction of preceding deciduous canine, orthodontic traction, and surgical extraction followed by immediate replantation of the extracted tooth at the proper position(autotransplantation). Autotransplantation is considered as the treatment of choice when surgical exposure and subsequent orthodontic traction are difficult or impossible due to unfavorable impacted position. The prognosis of autotransplantation is affected by the degree of apex formation, surgical procedures performed, timing of root canal treatment, and length of stabilization period. In these two cases presented, the patients with unerupted maxillary canine were treated with autotransplantation. One case was thought that guidance of eruption by orthodontic traction was difficult because of its unfavorable impacted position. In the other case, parents didn't agree to treat by orthodontic traction, therefore autotransplantation was done. In both cases, autotransplantation was carried out following root canal treatment and orthodontic treatment, and both cases have demonstrated to be successful to this day.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.27 no.3
• /
• pp.383-387
• /
• 2000

Fusion is defined as union of two separate tooth buds at some stage in their development with confluence of dentin and characterized by separate root canal and large single crown, while gemination is defined as an attempt of the single tooth bud to incompletely divide and usually result in a single root with one root canal and two completely or incompletely separated crowns. It is sometimes difficult to decide whether an abnormally large tooth is the result of fusion of a normal and a supernumerary tooth, or of gemination; use of the term 'Double tooth' may make the clinicians avoid this difficulty(Brook & Winter). Commonly there are no symptoms, but the problems associated with these anomalies include esthetics, possible loss of arch length and delayed or ectopic eruption of the permanent teeth, caries along the line of demarcation, and periodontal disease. Commonly, it dose not need to be treated in primary dentition but in case of permanent dentition, it may be requested to be treated due to esthetics and other problems. In our case, a 8 years old girl showed a Double tooth, we attained the favorable results by performing hemisection with apexification.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.23 no.2
• /
• pp.61-69
• /
• 1981

The paddies in the hillsides in Gonggeun-myeon, Hoingseong-gun, Kangweon-do keep a steep slope and run in and out. A land consolidation in such an area, therefore, will require high ratio of land loss and a large amount of earth moving if it follows the existing design criteria to separate drainage and irrigation ditches in a scheme. Due to the consequent decrease in construction cost, the project has not been envisaged. in order to secure the introduction of small-medium size farm machineries into the paddies, farm plots were planned to be straight and drainage with taking care of topography. Findings from the comparison of methodologies are as follows. 1. In places with a solpe of more than 1/30, a reduction in earth moving can be expected with parallel plots to the contours. 2, For the sake of effective using of farm machineries, it is thought that a plot should be running straight parallel to the contours and the ratio of length and width of a plot be more than six. 3. In places with a slop of more than 1/10, a reduction in earth moving and a effective introduction of farm-machineries can he expected with straight parllel plots to the contours. But it is undesirable to introduce a scheme in this places because of the difficulties in acreage computation and farmers' hesitation. 4. The system with a canal for both irrigation and drainage is highly effective to decrease the ratio of land loss as well as construction cost. 5. Parallel plots to the contours and a canal for both irrigation and drainage are highly effective in the decrease in construct cost. 6. To avoid the subdivision of a cooperation in farming is desirable of a plots, has more than two owners.

• Restorative Dentistry and Endodontics
• /
• v.39 no.4
• /
• pp.270-275
• /
• 2014

Objectives: This study compared the mechanical properties of various instruments for canal exploration and glide-path preparations. Materials and Methods: The buckling resistance, bending stiffness, ultimate torsional strength, and fracture angle under torsional load were compared for C+ file (CP, Dentsply Maillefer), M access K-file (MA, Dentsply Maillefer), Mani K-file (MN, Mani), and NiTiFlex K-file (NT, Dentsply Maillefer). The files of ISO size #15 and a shaft length of 25 mm were selected. For measuring buckling resistance (n = 10), the files were loaded in the axial direction of the shaft, and the maximum load was measured during the files' deflection. The files (n = 10) were fixed at 3 mm from the tip and then bent $45^{\circ}$ with respect to their long axis, while the bending force was recorded by a load cell. For measuring the torsional properties, the files (n = 10) were also fixed at 3 mm, and clockwise rotations (2 rpm) were applied to the files in a straight state. The torsional load and the distortion angle were recorded until the files succumbed to the torque. Results: The CP was shown to require the highest load to buckle and bend the files, and the NT showed the least. While MA and MN showed similar buckling resistances, MN showed higher bending stiffness than MA. The NT had the lowest bending stiffness and ultimate torsional strength (p < 0.05). Conclusions: The tested instruments showed different mechanical properties depending on the evaluated parameters. CP and NT files were revealed to be the stiffest and the most flexible instruments, respectively.

• Imaging Science in Dentistry
• /
• v.51 no.3
• /
• pp.251-260
• /
• 2021

Purpose: Dental implants are widely used for the rehabilitation of edentulous sites. This study investigated the occurrence of dental implant malpositioning as shown on post-implantation cone-beam computed tomography (CBCT) and to identify related factors. Materials and Methods: Samples with at least 1 malpositioned dental implant were collected from a central radiology clinic in Tehran, Iran from January 2017 to January 2019. Variables such as demographic characteristics, length and diameter of implants, type of implant, sites of implant insertion, different types of implant malpositioning problems (cortical plate perforation, interference with anatomical structures), angulation of the implant, and the severity of malpositioning were assessed. In addition, the incidence of implant fracture and over-drilling was evaluated. Data were statistically analyzed using the chi-square test, 1-sample t-test, and Spearman correlation coefficients. Results: In total, 252 patients referred for implant postoperative CBCT evaluations were assessed. The cases of implant malpositioning included perforation of the buccal cortical plate (19.4%), perforation of the lingual cortical plate (14.3%), implant proximity to an adjacent implant (19.0%), implant proximity to an adjacent tooth (3.2%), interference with anatomical structures(maxillary sinus: 18.3%, mandibular canal: 11.1%, nasal cavity: 6.3%, mental foramen: 5.6%, and incisive canal: 0.4%). Implant fracture and over-drilling were found in 1.6% and 0.8% of cases, respectively. Severity was categorized as mild (9.5%), moderate (35.7%), severe (37.7%), and extreme (17.1%), and 52.4% of implants had inappropriate angulation. Conclusion: CBCT imaging is recommended for detecting dental implant malpositioning. The most common and severe type of malpositioning was buccal cortex perforation.

• Restorative Dentistry and Endodontics
• /
• v.31 no.5
• /
• pp.378-389
• /
• 2006

The purpose of this study was to compare the sealing ability of root canal obturation with or without the treatment of smear layer. Eighty extracted human teeth with one canal were selected Instrumentation was performed with crown-down technique. After instrumentation, root canals of the NaOCl group and NaOCl-6 group were irrigated with 3% NaOCl. EDTA group and EDTA-6 group were irrigated with 17% EDTA. Then all teeth were obturated using continuous wane obturation technique NaOCl group and EDTA group were immersed in methylene blue solution for 84hours. NaOCl-6 group and EDTA-6 group were immersed in methylene blue solution for 6months. The teeth were sectioned at 1.5 mn (Level 1), 3.0 mm (Level 2) and 4.5 mm (Level 3) from the root apex. The length of dye-penetrated inter-face and the circumferential length of canal at each level were measured using Sigma-Scan Pro 5.0. 1. The mean leakage ratio was decreased cervically. 2. NaOCl group showed higher mean leakage ratio than EDTA group at each level. But there was significant difference at level 1 only (p < 0.05). 3. NaOCl-6 group showed higher mean leakage ratio than EDTA-6 group at each level. But there was significant difference at level 1 only (p < 0.05). 4. NaOCl-6 group showed higher mean leakage ratio than NaOCl group at each level. But there was significant difference at level 1 only (p < 0.05). 5. EDTA-6 group showed higher mean leakage ratio than EDTA group at each level. But there was no significant difference. 6. In NaOCl group and NaOCl-6 group, scanning electron micrographs of tooth sections generally covered with smear layer. In EDTA group and EDTA-6 group, tooth sections showing the penetration of sealers to opened dentinal tubules. The results suggest that removal of smear layer was effective to reduce the apical microleakage of the root canal.