• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.65-73
• /
• 2007

The use of an Exhaust Gas Recirculation(EGR) for a diesel engine with variable geometry turbocharger(VGT) has confronted how to obtain the amount of EGR for NOx reduction requirement at wide operating range and less side effect. Through a combined effort of modeling(wave action simulation) and experiment, an investigation into the effect of EGR area ratio and pipe length on EGR characteristics of common rail diesel engine with VGT has been performed. For accurate computation, calibration of constants involved in empirical and semi-empirical correlations has been performed at a specific operating point, before of its use for engine simulation. From the results of this study, it was found that EGR rate is sharply increased with increasing EGR area ratio until area ratio of 0.3. However, the effect of EGR area ratio on EGR rate is negligible beyond this criteria. This study also investigates the effect of EGR pipe length on a EGR amount and pulsating flow characteristics at EGR junction. The results showed that the longer EGR pipe length, the lower EGR amount was achieved due to the flow loss resulting in lower amplitude of pressure wave.

• Nuclear Engineering and Technology
• /
• v.52 no.6
• /
• pp.1271-1276
• /
• 2020

The geometrical efficiency of a source-to-detector configuration is considered to be necessary in the calculation of the full energy peak efficiency, especially for NaI(Tl) and HPGe gamma-ray spectroscopy detectors. The geometrical efficiency depends on the solid angle subtended by the radioactive sources and the detector surfaces. The present work is basically concerned to establish a new mathematical approach for calculating the solid angle and geometrical efficiency, based on conversion of the geometrical solid angle of a non-axial radioactive point source with respect to a circular surface of the detector to a new equivalent geometry. The equivalent geometry consists of an axial radioactive point source with respect to an arbitrary elliptical surface that lies between the radioactive point source and the circular surface of the detector. This expression was extended to include coaxial radioactive circular disk source. The results were compared with a number of published data to explain how significant this work is in the efficiency calibration procedure for the γ-ray detection systems, especially in case of using isotropic radiating γ-ray sources in the form of point and disk shapes.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.5
• /
• pp.460-465
• /
• 2007

This paper deals with the Fine Digital Sun Sensor (FDSS) for Science & Technology Satellite 2(STSAT-2). The FDSS was firstly developed by using CMOS-Image sensor(CIS) in South Korea. This paper will describe the configuration of the FDSS, the design of the optical part, the analysis result of the optical characteristics of the sunlight, and the calibration result measured by solar simulator.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1634-1637
• /
• 2003

Any given object on the motor-driven turntable is pictured from 8 to 72 different views with a digital camera. 3D shape reconstruction is performed with the integrated software called by Scanware from these multiple digital photographs. There are several steps such as configuration, calibration, capturing, segmentation, shape creation, texturing and merging process during the shape reconstruction process. 3D geometry data can be exported to cad data such as Autocad input file. Also 3D image model is generated from 3D geometry and texture data, and is used to advertise the model in the internet environment. Consumers can see the object realistically from wanted views by rotating or zooming in the internet browsers with Scanbull spx plug-in. The spx format allows a compact saving of 3D objects to handle or download. There are many types of scan equipments such as laser scanners and photogrammetric scanners. Line or point scan methods by laser can generate precise 3D geometry but cannot obtain color textures in general. Reversely, 3D image modeling with photogrammetry can generate not only geometries but also textures from associated polygons. We got various 3D image models and introduced the process of getting 3D image model of an internet-connected watchdog robot.

• Smart Structures and Systems
• /
• v.10 no.3
• /
• pp.209-228
• /
• 2012

Structural health monitoring with wireless sensor networks has received much attention in recent years due to the ease of sensor installation and low deployment and maintenance costs. However, sensor network technology needs to solve numerous challenges in order to substitute conventional systems: large amounts of data, remote configuration of measurement parameters, on-site calibration of sensors and robust networking functionality for long-term deployments. We present a structural health monitoring network that addresses these challenges and is used in several deployments for monitoring of bridges and buildings. Our system supports a diverse set of sensors, a library of highly optimized processing algorithms and a lightweight solution to support a wide range of network runtime configurations. This allows flexible partitioning of the application between the sensor network and the backend software. We present an analysis of this partitioning and evaluate the performance of our system in three experimental network deployments on civil structures.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.6
• /
• pp.773-780
• /
• 2003

The three-dimensional spatial structures of impeller flow created by a six bladed Rushton turbine have identified based on the volumetric velocity information from multi-plane stereoscopic PIV measurements. A total of 10 planes with 2 mm space and a 50 mm by 64 mm size of the field of view were targeted. To reduce the depth of focus, we adopted an angle offset configuration which satisfied the Scheimpflug condition. The distortion compensation procedure was utilized during the in situ calibration. Phase-locked instantaneous data were ensemble averaged and interpolated in order to obtain mean 3-D. volumetric velocity fields on a 60 degree sector of a cylindrical ring volume enclosing the turbine blade. Using the equi-vorticity surface rendering, the spatial structure of the trailing vortices was clearly demonstrated. Detail flow characteristics of the radial jet reported in previous studies of mixer flows were easily identified.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.12
• /
• pp.2146-2155
• /
• 1997

This paper presents the Wire Parallel Mechanism for robot pose measurement which can be used to robot calibration. It is constructed with six parallel links using wire. The position and orientation of the end effector of a robot are calculated from the wire length that measured by the encoder. The unique solution is obtained from a Newton-Raphson method and geometric configuration of the mechanism, also the method to estimate a measuring space is presented. Through the simulations, it is verified that the proposed mechanism can measure a robot pose, and has a large measuring space. In conclusion, it can be used effectively in a robot pose measurement with little cost and effort.

• Korean Journal of Remote Sensing
• /
• v.34 no.4
• /
• pp.639-647
• /
• 2018

This paper presents TerraSAR-X and KOMPSAT-5 sigma nought variation according to season and antenna observation configuration in Mongolia. Two types of landcover including bare surface and cropland were examined. The seasonal variation of sigma nought in cropland was about 7 dB and particularly a significant sigma nought reduction occurred after harvest. On the contrary, the Mongolia bare surface provides a consistent sigma nought values for several years with an annual variation less than 2.5 dB of standard deviation. However, the bare soil was relatively sensitive to look-direction (or ascending or descending mode) as well as incidence angle while the cropland was almost independent of antenna look-direction and small incidence angle changes. Although the look-directional variation of bare surface sigma nought was observed in this study, the look-direction anisotropic nature of the surface was not well examined. A further study would be required to account for this feature with various SAR observation configurations.

• Journal of electromagnetic engineering and science
• /
• v.10 no.4
• /
• pp.282-289
• /
• 2010

A simplified, practical vector network analyzer (VNA) that uses mature radio-over-fiber technology has been designed and demonstrated. The measurement concept allows the full S-parameters of a microwave device (or antenna) to be obtained while minimizing the detrimental effects of electrical cables, which are replaced with a photonic link. A variety of high-frequency light modulation schemes with frequency sweeping capabilities are presented to realize a one-path (single, forward), frequency-multiplied optical link for VNA applications. Using the photonic one-path link, full two-port S-parameters have been extracted based on five-term error modeling, which has half the error terms compared with the standard duplex configuration. The S-parameters of a microwave filter and antenna measured using frequency-multiplied optical links are found to be in good agreement with those obtained using a conventional VNA.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.5
• /
• pp.640-647
• /
• 2004

In order to perform elastic-plastic fracture mechanical analyses, fracture resistance curves for concerned materials are required. The unloading compliance method and the DCPD(Direct Current Potential Drop) method have been widely used for measuring the crack length and the extension for a standard specimen fracture resistance curve test. However it is difficult to apply the unloading compliance method to a real pipe fracture resistance curve test. The objective of this paper is to propose the calibration equation between the normalized crack length and the normalized electric potential, and to apply to pipe fracture experiments. For these, finite element analyses were performed with various current input locations and crack front configurations. Also the 4-point bending jig was manufactured for a pipe test and the DCPD method was used to measure crack extensions and crack lengths for a pipe test. The calculated crack length by the DCPD method agreed with the measured crack length within 5% error.