• Proceedings of the IEEK Conference
• /
• summer
• /
• pp.133-136
• /
• 2004

We are going to procedure various view from two frontal image using trifocal tensor. We found that warping is effective to produce synthesized poses of a face with the small number of mesh point of a given image in previous research[1]. For this research, fundamental matrix is important to calculate trifocal tensor. So, in this paper, we investigate two existing algorithms: Hartley's[2] and Kanatani's[3]. As an experimental result, Kenichi Kantani's algorithm has better performance of fundamental matrix than Harley's algorithm. Then we use the fundamental matrix of Kenichi Kantani's algorithm to calculate trifocal tensor. From trifocal tensor we calculate new trifocal tensor with rotation input and translation input and we use warping to produce new virtual views.

• Journal of Environmental Science International
• /
• v.15 no.10
• /
• pp.967-973
• /
• 2006

In this study used tank model and specific discharge to calculate low-flow of mountain basin and supply data that need in water resources plan. Low-flow is calculated byspecific discharge and area ratio method as resulted that calculate storage of low-flow by tank model was construed that showd all similar aspect. In judged to help in water resources plan establishment calculating low-flow using model to supplement uncertainty of observed data in that calculate of low-flow ungaged mountain area. It shows by economical and realistic plan until 12 years after development that run parallel and use economic performance analysis result valley flow and groundwater. But wide area water services and Chungju dam since 12 years onward was expose that is economic.

• Journal of the Korea Safety Management & Science
• /
• v.9 no.5
• /
• pp.111-116
• /
• 2007

The objective of this paper is to calculate the minimum scale of management for transportation business in order to achieve a form of enterprise. In this study the tracking minimum scale of business is the minimum number of operating trucks. Transportation companies should ensure the number of trucks for a type of business model rather than a means of livelihood model. The method to calculate the minimum number of trucks for the transportation business model can use an approach of either the qualitative and the quantitative technique. This study chooses the quantitative technique to calculate the minimum number of trucks through the analysis of break-even point.

• Journal of the Korea Society of Computer and Information
• /
• v.23 no.10
• /
• pp.95-101
• /
• 2018

In this paper, we propose an image-based synthesis method that can effectively represent the spark effect in fire simulation. We use the real flame image or animated image as inputs and perform the following steps : 1) extract feature vectors from the image, 2) calculate artificial buoyancy, and 3) generate and advect spark textures. We detect the edge from images and then calculate the feature vectors to calculate the buoyancy. In the next step, we compute the high-quality buoyancy vector field by integrating the two-dimensional feature vector and the fluid equation. Finally, the spark texture is advect by buoyancy field. As a result, our method is performed much faster than the previous approach and high-quality results can be obtained easily and stably.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.10 no.5
• /
• pp.273-279
• /
• 2015

The vehicle has lots of embedded systems. Each of systems has its own role. In case of the vehicle, simple failure of system can be critical to driver. Therefore all of embedded system should be managed based on importance factors to be effective. In this paper, we consider the resilience as the importance factor for the driving system with ACC(Adaptive Cruise Control). We propose metrics to calculate the resilience of the embedded system. To get the resilience of system, we calculate the reliability and the resilience of nodes in the system using its failure rate. The resilience of whole system can be presented by the resilience of nodes and its weight. We calculate the resilience and compare the centralized structure and the distributed structure.

• Proceedings of the KIEE Conference
• /
• 2003.11a
• /
• pp.38-40
• /
• 2003

This paper describes the integrated dynamic stability(IDS) program for tuning the power system controllers, such as PSS, AVR and so on. IDS consists of three modules; power flow module, PWRLF, to calculate large scale power system load flow solutions, IDS/PSS module to calculate eigenvalues and frequency response in the range of frequency from 0.2Hz to 2Hz, and IDS/NEA module to calculate eigenvalues in the range of frequency from 5.0Hz to 55Hz. In addition, IDS provides graphic user interface(GUI) in order to let the user handle and analyze the input data and the results of calculation with convenience.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.7 no.2
• /
• pp.61-70
• /
• 1970

Since there has been no analytical method to calculate principal dimensions of the axial vibration damper of marine diesel engine shaftings in design state, it has often happened to install the axial vibration damper after the ship's trial trip. In this paper a method to calculate the coefficient of equivalent damping of the axial vibration damper is introduced and with this value one can calculate fairy accurate vibrating amplitudes of the crankshaft that is fitted with an axial vibration damper, by using author's matrix methods.[1][2][3][4] A comparison of the calculated amplitudes with measured ones is shown and its result is fairy good, except values of the case where the damper nozzle is almost closed.

• International journal of advanced smart convergence
• /
• v.8 no.2
• /
• pp.147-154
• /
• 2019

In this paper, we conducted a study that utilizes deep learning to calculate appropriate physical exercise information when basic human factors such as sex, age, height, and weight of users come in. To apply deep learning, a method was applied to calculate the amount of fat needed to calculate the amount of one repetition maximum by utilizing the structure of the basic Deep Neural Network. By applying Accuracy improvement methods such as Relu, Weight initialization, and Dropout to existing deep learning structures, we have improved Accuracy to derive a lean body weight that is closer to actual results. In addition, the results were derived by applying a formula for calculating the one repetition maximum load on upper and lower body movements for use in actual physical exercise. If studies continue, such as the way they are applied in this paper, they will be able to suggest effective physical exercise options for different conditions as well as conditions for users.

• Progress in Superconductivity and Cryogenics
• /
• v.12 no.2
• /
• pp.13-16
• /
• 2010

The superconducting synchronous motor or generator mostly has high permeability iron only around outer yoke portion. Therefore, if excitation voltage (Back E.M.F) is calculated from 2 dimensional magnetic field distributions, it can be largely different from actual value due to additional voltage originated from end coils. In order to calculate the excitation voltage more accurately, 3 dimensional magnetic field calculation is necessary for including the end coil effect from large air-gap structure. The excitation voltage can be calculated by stator (armature) coil linkage flux originated from rotor (field) coil excitation, but it is difficult to calculate the flux linkage exactly because of complicated structure of the stator coil. This paper shows a method to calculate the excitation voltage from 3 dimensional magnetic energy that can be calculated directly from volume integration of magnetic flux density and field intensity scalar product through FEM (Finite Element Method) analysis software.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.117-118
• /
• 2023

Estimating the construction period at the initial stage of the project and determining whether it is appropriate is very important for the developer's decision-making and the success of the construction company's business. Existing researchers have conducted various studies to calculate the appropriate construction period, but there is no study on the influencing factors and methodology for the construction period of beam-column PC apartment building frame construction. The purpose of this study is to calculate the PC member assembly time using the mathematical algorithm of PC member assembly. The results of this study can be used as basic data to calculate the construction date of the standard floor of PC construction.