• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.5
• /
• pp.112-118
• /
• 2003

The friction coefficients of the rubber for clutch master cylinder were experimentally measured in this study. The cylindrical rubber samples for primary cup-seal and secondary cup-seal were tested against the aluminum or the steel plates of master cylinder housing under the various conditions of brake oil temperatures and normal loads. Dry sliding friction coefficients were also measured under various load conditions. The test revealed following results. First, the friction coefficient under fluid lubrication condition in general decreases, as the oil temperature or normal load increases. Second, the steel plate of low surface roughness yielded comparatively low friction coefficient on the range of 0.30∼0.67. On the other hand, the aluminum plate of high surface roughness yielded high friction coefficient on the range of 0.31∼1.15. Third, the friction coefficient of dry surface contact decreases as the normal load increases. This is contrary to the general principle of friction coefficient between metal plates.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.10
• /
• pp.1950-1956
• /
• 2017

In food-printing field, precise positioning technique for a printing object is very important. In this paper, we propose cup positioning method for a latte-art printer through image processing. A camera sensor is installed on the upper side of the printer, and the image obtained from this is projected and converted into a top-view image. Then, the edge lines of the image is detected first, and then the coordinate of the center and the radius of the cup are detected through a Circular Hough transformation. The performance evaluation results show that the image processing time is 0.1 ~ 0.125 sec and the cup detection rate is 92.26%. This means that a cup is detected almost perfectly without affecting the whole latte-art printing time. The center point coordinates and radius values of cups detected by the proposed method show very small errors less than an average of 1.5 mm. Therefore, it seems that the problem of the printing position error is solved.

• Journal of Korea Water Resources Association
• /
• v.53 no.5
• /
• pp.347-356
• /
• 2020

The main objective of the study is to propose the most efficient SWAT model calibration method using SWAT-CUP with less computing time and high performance. In order to achieve the goal, Case1-3 (250, 500, and 1,000 simulation runs) and Case4 (1,000 simulation runs in the first iteration and then 500 simulation runs for the following iterations) were defined to compare the results. When evaluating the values of the objective function, Case2 and Case3 reached the same value after the fourth iteration, and Case1 reached the closed value of Case2-3 after the eighth iteration. However, the final estimates of the parameters had different ranges in Cases1-3, and only the results of Case3 and Case4 converged similarly. Thus, it can be considered that the parameter calibration results are highly affected by the initial number of simulation runs. On the other hand, SWAT simulation results did not show the significant difference after the first iteration, unlike the parameter ranges. From the analysis results, we can conclude that the most suitable and effective method was to repeat one or two times of iterations with a sufficient number of simulation runs, as in Case4.

• Ecology and Resilient Infrastructure
• /
• v.3 no.1
• /
• pp.35-45
• /
• 2016

The correlation relationships and their corresponding equations between the geomorphological parameters and the Soil Water Assessment Tool (SWAT) model parameters by Sequential Uncertainty Fitting - version 2 (SUFI-2) algorithm of SWAT Calibration and Uncertainty Programs (SWAT-CUP) were developed at the Seom-river experimental watershed. The parameters of the SWAT model at the Soksa-river experimental watershed were estimated by the developed equations. The SWAT model parameters were estimated by SUFI-2 algorithm of SWAT-CUP with rainfall-runoff data from the Soksa-river experimental watershed from 2000 to 2007. Rainfall-runoff simulation of the SWAT model was carried out at the Soksa-river experimental watershed from 2000 to 2007 for the applicability of the estimated parameters by the developed equations. The root mean square errors (RMSE) between the observed and the simulated rainfall-runoffs using the estimated parameters by developed equations of correlation analysis and the optimum parameters by SUFI-2 of SWAT-CUP were $1.09m^3/s$ and $0.93m^3/s$ respectively at the Soksa-river experimental watershed from 2000 to 2007. Therefore, it is considered that the parameter estimation of the SWAT model by the geomorphological characteristics parameters has applicability.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.6
• /
• pp.1193-1202
• /
• 1996

This study investigates and analyzes the amount and shape of the front waist dart of the bodice and investigates the dart division method by bust size. Measurements at 5 arm positions were taken from 15 subjects. Clothing tests were given to 6 of the subjects. The conclusions were as follows: 1) Front Body surface changes were occurred around armpit and they were caused by the wrinkles of the armpit 2) The curved dart line was more appropriate for use with C cup, the large bust body, than the linear line. The changes of the dart amount at arm movements had different types by bust size. 3) Patterns for A & C cup body were adequate to divide the dart amount by 3 darts such as under the B.P., under the anterior armpit and side line, or to aggregate to 1 dart under the B.P. For the B cup body, however, the suitable pattern to use was the total dart amount divided by 1~2 darts and decreasing the waist line at the side line should be avoided.

• Transactions of Materials Processing
• /
• v.15 no.7 s.88
• /
• pp.504-511
• /
• 2006

The drawability of AZ31B magnesium sheet is estimated at various temperatures($200,\;250,\;300,\;350\;and\;400^{\circ}C$), and forming speed(20, 50, 100mm/min), thickness(0.5, 0.8, 1.0, 1.4mm). The deep drawing process of circular cup and square cup were used in forming experiments. Experimental and FEM analysis are performed to investigate drawability and affection of controlled blank holding force. Through the controlled blank holding force, drawability was improved. Limit drawing ratio is increased from 2.1 to 3.0 in circular cup drawing and change of thickness is decreased from 16.3 to 6.9%. This result is verified by FEM analysis. Through the observation of microstructure, the main cause is investigated as a quantity of the dynamic recrystallization.

• East Asian mathematical journal
• /
• v.21 no.1
• /
• pp.61-64
• /
• 2005

Let R be a commutative ring with identity, and let $f,\;g_i(i=1,\;\ldots,\;n),\;g_{\alpha}(\alpha{\in}S)$ be elements of R. We show that the following statements are equivalent; (i) $X_f{\subseteq}{\cup}_{\alpha{\in}S}X_{g\alpha}$ only if $X_f{\subseteq}X_{g\alpha}$ for some $\alpha{\in}S$, (ii) $V(f){\subseteq}{\cup}_{\alpha{\in}S}V(g_{\alpha})$ only if $V(f){\subseteq}V(g_{\alpha})$ for some $\alpha{\in}S$, (iii) $V(f){\subseteq}{\cup}^n_{i=1}V(g_i)$ only if $V(f){\subseteq}V(g_i)$ for some i, (iv) Spec(R) is linearly ordered under inclusion.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.1
• /
• pp.190-198
• /
• 1989

Some Developments in computer aided procedures for cold forging process and tool design of rotationally symmetric cup shape parts are described. The developed system enables appropriate forging sequence to be determined automatically, together with details of corresponding preform, die and punch design. The computer program developed is interactive and written in BASIC. This system not only assist the heavy work of designers but greatly shorten the time of design.

• The Korean Journal of Community Living Science
• /
• v.28 no.1
• /
• pp.69-79
• /
• 2017

The purpose of this study was to compare fitting of the upper garment by brassiere cup size and types of bodice block. This study conducted a 3D virtual garment system by applying three types of bodice block (I, II, III) and experimental pattern of the bodice block to 3D avatars of four individuals with the following measurements: under bust circumference of 73.5 cm and bust circumferences of 83.5 cm, 86.0 cm, 88.5 cm, and 91.0cm. The results of the study were as follows. First, for 83.5 cm bust circumference (A Cup), appearance of the three types of bodice block (I, II, III) was appropriate. However, as bust circumference increased in size, shape became inappropriate. The depth and width of the armhole, within 15 cm and 11 cm, respectively, were found to be appropriate. In case of 91.0 cm bust circumference (D Cup), all three bodices (I, II, III) were inappropriate. Second, the results of the draft of the experimental patterns of the bodice block of bust circumference measuring 83.5 cm, 86.0 cm, 88.5 cm, and 91.0 cm in the 3D avatars of the four individuals revealed similarities in the frontal view of the silhouette in the four avatars; in the case of the lateral view of the silhouette, lateral width grew wider as bust circumference of the silhouette became larger, but the shape of armhole showed no changes. The depth of the armhole showed little changes from 15.1 cm to 15.22 cm, and the height of sleeve (armscye depth 13.6 cm within +2 cm) remained similar. The difference in width of the armhole from 11.26 cm to 11.37 cm was rather small. The width of the upper sleeve (8.97 cm) seemed to be appropriate as it remained within the 2-3 cm boundary.

• Fire Science and Engineering
• /
• v.26 no.2
• /
• pp.84-89
• /
• 2012

For the safe handling of n-nonanol, this study was investigated the explosion limits of n-nonanol in the reference data. The flash points and AITs (autoignition temperatures) by ignition delay time were experimented. As a results, the lower and upper explosion limits of n-nonanol recommended 0.8 Vol.% and 6.1 Vol.%, respectively. The lower flash points of n-nonanol by using closed-cup tester were experimented $94{\sim}97^{\circ}C$. The lower flash points of n-nonanol by using open cup tester were experimented $103{\sim}104^{\circ}C$. This study measured relationship between the AITs and the ignition delay times by using ASTM E659-78 apparatus for n-nonanol. The experimental AIT of n-nonanol was $270^{\circ}C$.