• Journal of Environmental Science International
• /
• v.20 no.2
• /
• pp.251-260
• /
• 2011

$TiO_2$- and $SiO_2$-supported $Co_3O_4$, Pt and $Co_3O_4$-Pt catalysts have been studied for CO and $C_3H_8$ oxidations at temperatures less than $250^{\circ}C$ which is a lower limit of light-off temperatures to oxidize them during emission test cycles of gasoline-fueled automotives with TWCs (three-way catalytic converters) consisting mainly of Pt, Pd and Rh. All the catalysts after appropriate activation such as calcination at $350^{\circ}C$ and reduction at $400^{\circ}C$ exhibited significant dependence on both their preparation techniques and supports upon CO oxidation at chosen temperatures. A Pt/$TiO_2$ catalyst prepared by using an ion-exchange method (IE) has much better activity for such CO oxidation because of smaller Pt nanoparticles, compared to a supported Pt obtained via an incipient wetness (IW). Supported $Co_3O_4$-only catalysts are very active for CO oxidation even at $100^{\circ}C$, but the use of $TiO_2$ as a support and the IW technique give the best performances. These effects on supports and preparation methods were indicated for $Co_3O_4$-Pt catalysts. Based on activity profiles of CO oxidation at $100^{\circ}C$ over a physical mixture of supported Pt and $Co_3O_4$ after activation under different conditions, and typical light-off temperatures of CO and unburned hydrocarbons in common TWCs as tested for $C_3H_8$ oxidation at $250^{\circ}C$ with a Pt-exchanged $SiO_2$ catalyst, this study may offer an useful approach to substitute $Co_3O_4$ for a part of platinum group metals, particularly Pt, thereby lowering the usage of the precious metals.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.8
• /
• pp.2748-2752
• /
• 2012

Cr(III) and Co(III) complexes with acetylacetonate were anchored onto a mesoporous MCM-41 through Schiff condensation. The materials were characterized by XRD, FT-IR, BET, CHN and ICP techniques. Elemental analysis of samples revealed that one C=N bond was formed through Schiff condensation on MCM-41 surface. The catalysts were tested for the alcohol oxidations using t-butyl hydroperoxide (TBHP) and $H_2O_2$ as oxidant. The catalytic experiments were carried out at both room temperature and reflux condition. Various solvents such as dichloromethane, acetonitrile and water were examined in the oxidation of alcohols. Among the different solvents, catalytic activity is found more in acetonitrile. Further, the catalysts were recycled three times in the oxidation of alcohols and no major change in the conversion and selectivity is observed, which shows that the immobilized metal-acetylacetonate complexes are stable under the present reaction conditions.

• Korean Chemical Engineering Research
• /
• v.47 no.3
• /
• pp.292-302
• /
• 2009

The wet oxidation of phenol has been investigated at temperatures from 150 to $250^{\circ}C$ and oxygen partial pressures from 25.8 to 75.0 bar with initial pH of 1.0 to 12.0 and initial phenol concentration of 10 g/l. Chemical Oxygen Demand COD has bee measured to estimate the oxidation rate. Reaction intermediates have been identified and their concentration profiles have been determined using liquid chromatography. The destruction rate of phenol have shown the first-order kinetics with respect to phenol and the changes in COD during wet oxidation have been described well with the lumped model. The impact of various homogeneous catalysts, such as $Cu^{2+}$, $Fe^{2+}$, $Zn^{2+}$, $Co^{2+}$ and $Ce^{3+}$ ions, on the destruction rate of phenol and COD has also been studied. The homogeneous catalyst of $CuSO_4$ has been found to be the most effective for the destruction of phenol and COD during wet oxidations. The destruction rate of formic acid formed during wet oxidations of phenol have increased as increasing temperature and $CuSO_4$ concentration. The final concentrations of acetic acid which has been formed during wet oxidations and difficult to oxidize have increased with reaction temperature and with decrease in the catalyst load.