• Journal of the Korea Society for Simulation
• /
• v.17 no.4
• /
• pp.199-208
• /
• 2008

Lately, since Complementary Metal Oxide Semiconductor(CMOS) image sensor system has low power, low cost and been miniaturized, hardware and applied software studies using these strengths are being carrying on actively. However, the products equipped with CMOS image sensor based polling method yet has several problems in degree of completeness of applied software and firmware, compared with hardware’s. CMOS image sensor system has an ineffective synchronous problem due to superfluous message exchange. Also when a sending of data is delayed continually, overhead of re-sending is large. So because of these, it has a problem in structural stability according to Polling Method. In this study, polling cycle was subdivided in high-speed synchronization method of firmware -based through MCU and synchronization method of Stepwise was proposed. Also, re-connection and data sending were advanced more efficiently by using interrupt way. In conclusion, the proposed method showed more than 20 times better performance in synchronization time and error connection. Also, a board was created by using C328R board of CMOS image sensor-based and ATmega128L which has low power, MCU and camera modules of proposed firmware were compared with provided software and analyzed in synchronization time and error connection.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4021-4030
• /
• 2015

Pulse wave is the physiological responses through the autonomic nervous system such as ECG. It is relatively convenient because it can measure the signal just by applying a sensor on a finger. So, it can be usefully employed in the field of U-Healthcare. The objects of this study are acquiring the PPG (Photoplethysmography) one of the way of measuring the pulse waves in non-invasive way using the CMOS image sensor on a smartphone camera, developing the portable system judging stressful or not, and confirming the applicability in the field of u-Healthcare. PPG was acquired by using image data from smartphone camera without separate sensors and analyzed. Also, with that image signal data, HRV (Heart Rate Variability) and stress index were offered users by just using smartphone without separate host equipment. In addition, the reliability and accuracy of acquired data were improved by developing additional hardware device. From these experiments, we can confirm that measuring heart rate through the PPG, and the stress index for analysis the stress degree using the image of a smartphone camera are possible. In this study, we used a smartphone camera, not commercialized product or standardized sensor, so it has low resolution than those of using commercialized external sensor. However, despite this disadvantage, it can be usefully employed as the u-Healthcare device because it can obtain the promising data by developing additional external device for improvement reliability of result and optimization algorithm.

• Current Industrial and Technological Trends in Aerospace
• /
• v.6 no.2
• /
• pp.125-132
• /
• 2008

High speed camera is very important and essential device to analyze the motion of fast moving object in detail. This paper describes the basic concepts of the high speed film camera and high speed digital camera and the history and future technical trends in high speed camera industry. In addition, application field of high speed camera in Korea as well as other countries and future plan to use high speed camera in Naro Space Center has been descried.

• Journal of information and communication convergence engineering
• /
• v.8 no.1
• /
• pp.51-58
• /
• 2010

This paper proposes an edge adaptive color interpolation for an ultra-small HD-grade complementary metal-oxide semiconductor (CMOS) video sensor in camera phones that can process 720-p/30-fps videos. Recently, proposed methods with great image quality perceptually reconstruct the green component and then estimate the red/blue component using the reconstructed green and neighbor red and blue pixels. However, these methods require the bulky memory line buffers in order to temporally store the reconstructed green components. The edge adaptive color interpolation method uses seven or nine patterns to calculate the six edge directions. At the same time, the threshold values are adaptively adjusted by the sum of the color values of the selected pixels. This method selects the suitable one among the patterns using two flowcharts proposed in this paper, and then interpolates the missing color values. For verification, we calculated the peak-signal-to-noise-ratio (PSNR) in the test images, which were processed by the proposed algorithm, and compared the calculated PSNR of the existing methods. The proposed color interpolation is also fabricated with the 0.18-${\mu}m$ CMOS flash memory process.

• Journal of the Korean Society of Radiology
• /
• v.13 no.7
• /
• pp.925-932
• /
• 2019

In this paper, we developed optical dosimetry system with a plastic scintillator, a commercial 50 mm, f1.8 lens, and a commercial high-sensitivity CMOS (complementary metal-oxide semiconductor) camera. And, the correction processors of vignetting, geometrical distortion and scaling were established. Using the developed system, we can measured a percent depth dose, a beam profile and a dose linearity for 6 MV medical LINAC (Linear Accelerator). As results, the optically measured percent depth dose was well matched with the measured percent depth dose by ion-chamber within 2% tolerance. And the determined flatness was 2.8%. We concluded that the optical dosimetry system was sufficient for application of absorbed dose monitoring during radiation therapy.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.1
• /
• pp.1-8
• /
• 2004

One of the most frequently used method for measurement of the degree of sizing (viz., hydrophobicity) is the Stockigt test. However, the Stockigt test was influenced by various factors such as dropping height, dropping amount, dropping speed and viewing angle. The resultant data of the sizing degree on the same specimen also varied according to different testers. Thus, the Stockigt test should be modified to be regarded as a highly reliable and reproducible standard method. For modifying the Stockigt test, it was required to quantify red coloration by reaction between 1％ ferric chloride and 2％ ammonium thiocyante during Stockigt testing. The cameras capturing the serial images during the red coloration process were the CMOS (Complementary Metal Oxide Semiconductor)-type and CCD (Charge Coupled Device)-type cameras. For measurement based on KS M 7025, the CCD-type camera must be used due to its high resolution, and on the other hand, for measurement based on Tappi Useful Method 429, the CMOS-type camera may be used owing to its low resolution. It was needed to covert the RGB values of a droplet image into HSV(Hue, Saturation, and Value) values because the human eyes are much closer to HSV than RGB. Among HSV values, the Hue value was accepted as the most reliable index consistent with the red coloration process by excluding the surrounding conditions such as light, tester's movement etc.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.4 s.316
• /
• pp.27-34
• /
• 2007

In this paper device driver for camera capture in hand held mobile system is implemented based on microsoft windows CE operating system. We also study the storage device driver based on the FAT fie system by using NAND flash memory as a storage device. We use the MBA2440 PDA board for implementing the hardware for image capture by using CMOS camera module producted by PixelPlus company. This camera module has VGA $640{\times}480$ pixel resolution. We also make application program which can be cooperated with the device driver for testing its performance, for example image capture speed and quality of captured image. We check that the application can be cooperated well not only with the device driver for camera capture but also with the device driver for FAT file system designed especially for the NAND flash memory.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.224-227
• /
• 1999

This paper presents a design of the real-time preprocessor for CMOS image sensor suitable to the digital camera applications. CMOS image sensor offers some advantages in on-chip integration, system power reduction, and low cost. However, it has a lower-quality image than CCDs. We describe an image enhancement algorithm, which includes color interpolation, color correction, gamma correction, sharpening, and automatic exposure control, to compensate for this disadvantage, and present its efficient hardware architecture to implement on the real-time processor. The presented real-time preprocessor was designed using VHDL, and it contains about 19.2K logic gates. We also implement our system on FPGA chips in order to provide the real-time adjustment and it was successfully tested.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.3
• /
• pp.597-602
• /
• 2013

In this paper, the lens module of mega pixel type was designed for barrel distortion calibration due to the barrel distortion of ultra wide angle. And the performance of this camera module was improved with the images from wide dynamic range 2 megapixel CMOS image sensor.

• Journal of the Optical Society of Korea
• /
• v.19 no.6
• /
• pp.658-664
• /
• 2015

Lens designers generally refer to flat image fields and attempt to minimize the field curvature. Present-day CMOS image sensors for mobile phone cameras, however, are not flat, but curved. Sometimes it is necessary to generate an intentional field curvature according to the degree and direction of the CMOS image-sensor’s curvature. This paper presents the degree of curvature of a CMOS image sensor measured using an interferometer, and proposes an effective compensation method that minimizes the net field curvature through optimizing the air gap between lens elements, which is demonstrated using simulations and experiments.