• Korean Journal of Soil Science and Fertilizer
• /
• v.50 no.5
• /
• pp.336-344
• /
• 2017

The soil water characteristics curve (SWCC) represents the relation between soil water potential and soil water content. The shape and range of SWCC according to the relation could vary depending on soil characteristics. The objective of the study was to estimate SWCC depending on soil types and layers and to analyze the trend among them. To accomplish this goal, the unsaturated three soils were considered: silty clay loam, loam, and sandy loam soils. Weighable lysimeters were used for exactly measuring soil water content and soil water potential. Two fitting models, van Genuchten and Campbell, were applied. Two models entirely fitted well the measured SWCC, indicating low RMSE and high $R^2$ values. However, the large difference between the measured and the estimated was found at the 30 cm layer of the silty clay loam soil, and the gap was wider as soil water potential increased. In addition, the non-linear decrease of soil water content according to the increase of soil water potential tended to be more distinct in the sandy loam soil and at the 10 cm layer than in the silty clay loam soil and at the lower layers. These might be seen due to the various factors such as not only pore size distribution, but also cracks by high clay content and plow pan layers by compaction. This study clearly showed difficulty in the estimation of SWCC by such kind of factors.

• Korean Journal of Agricultural Science
• /
• v.47 no.2
• /
• pp.263-273
• /
• 2020

With the change of the agricultural environment (increased rice production, decreased rice consumption, and rice production policies), converting paddy fields into upland fields is an increasing trend. In terms of conversion into upland fields, subsurface drainage is one of the most important factors for good field crop growth. This study evaluates the performance of a subsurface drainage culvert system in paddy fields and reclaimed lands. The obtained results are briefly summarized as follows: 1) After a comparative evaluation of several subsurface drainage culvert systems, including excavated subsurface drainage and non-excavated subsurface drainage types, type 3 (non-excavated, perforated drain pipe 50 mm, filter mat B50 cm, subsoiling 70 cm and culvert spacing 5 m) shows relatively high values among four types in terms of effectiveness (subsurface discharge capability) and economic efficiency (construction cost). 2) Type 3 has proven that it is suitable for design standards of discharge capacity through field tests performed in paddy fields (three sites: Gong-geom, Gae-san, Juk-san) and reclaimed lands (two sites: Gum-ho, Mi-am). 3) In the experiment of Sesamum indicum growth according to the existence of a drainage system, Sesamum indicum growth with a subsurface drainage culvert system had good value in terms of plant shoot and root length, shoot fresh and dry weight, and root fresh and dry weight).

• Nuclear Engineering and Technology
• /
• v.52 no.10
• /
• pp.2410-2414
• /
• 2020

Heavy ions have a high potential for destroying deep tumors that carry the highest dose at the peak of Bragg. The peak caused by a single-energy carbon beam is too narrow, which requires special measures for improvement. Here, carbon-12 (¹²C) ion with different energies has been used as a source for calculating the dose distribution in the water phantom, soft tissue and bone by the code of Monte Carlobased FLUKA code. By increasing the energy of the initial beam, the amount of absorbed dose at Bragg peak in all three targets decreased, but the trend for this reduction was less severe in bone. While the maximum absorbed dose per bone-mass unit in energy of 200 MeV/u was about 30% less than the maximum absorbed dose per unit mass of water or soft tissue, it was merely 2.4% less than soft tissue in 400 MeV/u. The simulation result showed a good agreement with experimental data at GSI Darmstadt facility of biophysics group by 0.15 cm average accuracy in Bragg peak positioning. From 200 to 400 MeV/u incident energy, the Bragg peak location increased about 18 cm in soft tissue. Correspondingly, the bone and soft tissue revealed a reduction dose ratio by 2.9 and 1.9. Induced neutrons did not contribute more than 1.8% to the total energy deposited in the water phantom. Also during ¹²C ion bombardment, secondary fragments showed 76% and 24% of primary 200 and 400 MeV/u, respectively, were present at the Bragg-peak position. The combined treatment of carbon ions with neutron or electron beams may be more effective in local dose delivery and also treating malignant tumors.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.1 s.62
• /
• pp.14-19
• /
• 2005

As a basic study for establishing the input conditions of a forecasting/estimating model, used for deep-sea water drainage to the ocean, this study was carried out as follows: 1) estimating the amount of river discharge and pollutant loads into the developing region of deep sea water in the East Sea, Korea, 2) a field observation of tidal current, vertical water temperature, and salinity distribution, 3) 3-D numerical experiment of tidal current to analyze the physical oceanographic status. The amount of river discharge flowing into this study area was estimated at about $462.7{\times}103 m\^3/day$ of daily mean in 2002. Annual mean pollutant load of COD, TN, and TP were estimated at 7.02 ton-COD/day, 4.06 ton-TN/day, and 0.39 ton/day, respectively. Field observation of tidal current normally shows 20-40cm/sec of current velocity at the surface layer, and it decreases under 20cm/sec as the water depth increases. We also found a stratification condition at around 30m water depth in the observation area. The differences in water temperature and salinity, between the surface layer and the bottom layer, were about 18 C and 0.8 psu, respectively. On the other hand, we found a definite trend of 34 psu salinity water mass in the deep sea region.

• The Journal of Korean Society for Radiation Therapy
• /
• v.10 no.1
• /
• pp.11-22
• /
• 1998

The absolute absorbed dose can be determined according to the measurement conditions ; measurement material, detector, energy and calibration protocols. The purpose of this study is to compare the absolute absorbed dose due to the differences of measurement condition and calibration protocols for photon beams. Dosimetric measurements were performed with a farmer type PTW and NEL ionization chambers in water, solid water, and polystyrene phantoms using 6MV photon beams from Siemens linear accelerator. Measurements were made along the central axis of $10{\times}10cm$ field size for constant target to surface distance of 100cm for water, solid water and polystyrene phantom. Theoretical absorbed dose intercomparisons between TG21 and IAEA protocol were performed for various measurement combinations on phantom, ion chamber, and electrometer. There were no significant differences of absorbed dose value between TG2l and IAEA protocol. The differences between two protocols are within $1\%\;while\;the\;average\;value\;of\;IAEA\;protocol\;was\;0.5\%$ smaller than TG2l protocol. For the purpose of comparison, all the relative absorbed dose were nomalized to NEL ion chamber with Keithley electrometer and water phantom, The average differences are within $1\%,\;but\;individual\;discrepancies\;are\;in\;the\;range\;of\;-2.5\%\;to\;1.2\%$ depending upon the choice of measurement combination. The largest discrepancy of $-25\%$ was observed when NEL ion chamber with Keithley electrometer is used in solid water phantom. The main cause for this discrepancy is due to the use of same parameters of stopping power, absorption coefficient, etc. as used in water phantom. It should be mentioned that the solid water phantom is not recommended for absolute dose calibration as the alternative of water, since absorbed dose show some dependency on phantom material other than water. In conclusion, the trend of variation was not much dependent on calibration protocol. However, It shows that absorbed dose could be affected by phantom material other than water.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.8 no.2
• /
• pp.77-85
• /
• 2006

Entomopathogenic nematodes (EPNs) have been used as biological control agents for control of various agro-forest insect pests, and are especially effective against soil-dwelling insect pests. Effect of soil moisture on pathogenicity of commercial EPNs for white grub control was evaluated in laboratory, pots, and golf courses. Pathogenicity of EPNs in sand column was variable depending on depth, soil moisture, and EPN species or strain. All tested EPNs (Heterorhabditis sp. GSNUH1, Heterorhabditis sp. GSNUH2, Steinernema carpocapsae GSN1, and S. longicaudum Nonsan strain) showed similar pathogenicity against the bait insect, great wax moth (Galleria mellonella) larva at 2 cm deep at a given soil moisture. However, pathogenicity of the Heterorhabditis sp. GSNUH1 strain was decreased with increasing soil moisture. Pathogenicity of S. carpocapsae GSN1 strain was the lowest in 3% soil moisture (v/w) at 7 cm depth. However, there was no difference in pathogenicity between Heterorhabditis sp. GSNUH2 and S. longicaudum Nonsan strain. Although pathogenicity of Heterorhabditis sp. KCTC 0991BP strain showed no difference against the 2nd instar of Exomala orientalis, that of the S. carpocapsae GSN1 strain was decreased in the laboratory depending on soil moisture. Highly pathogenic strain EPN, Heterorhabditis sp. KCTC 0991BP strain, showed higher pathogenicity at 100 mm irrigation than non-irrigation or 10 mm irrigation. However, poor pathogenic strain EPN, S. carpocapsae GSN1 strain, was not different in pathogenicity from the 2nd instar of Exomala orientalis in creeping bentgrass (Agrostis palustris) depending on irrigation amount in the pot. Pathogenicity of EPNs in field experiment at the tee of Ulsan golf club showed a similar trend to that in the pot experiment.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.4
• /
• pp.18-26
• /
• 2004

Timbers of 14 by 14 cm, 2.4 m long, were dried in a vacuum kiln to investigate vacuum drying characteristics using three types of heating methods, conduction heating with hot plate, the radio frequency (RF) heating and the combination of both (hybrid heating). Average drying rate is the highest for the hybrid heating and the lowest for the RF heating. Average specific energy is the highest for the RF heating and the lowest for conduction heating. Transverse moisture content distribution of dried timber revealed the convex profile for both conduction and the hybrid heating and moisture content increased from one face to the opposite face for the RF heating. Moisture content distribution along the length of timber increased from the end to the middle of timber length for conduction and the hybrid heating and decreased from the end to the middle of timber length for the RF heating. End- and surface checks for conduction heating were severer than the other heating methods. No internal check occurred in any heating methods. Drying characteristics of conduction heating showed in-between trend of the RF and the hybrid heating.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.1
• /
• pp.33-39
• /
• 2024

In this study, the basic properties of cement paste with varying replacement ratio of micro-silica and fumed silica were analyzed to determine the suitability of nanomaterials for use as concrete admixtures. Referring to the ultra-high strength mix, the fluidity of cement paste was evaluated according to the nanomaterial replacement rate and the compressive strength characteristics were compared and analyzed. The related properties of the reactive nanomaterials to the cement hydrate were analyzed using SEM and EDS to observe the microstructure and identify the components of the hydration product. The reactive nanomaterials used in this study had tap densities between 0.061 and 0.264 g/cm³, which were lower than SF. Micro silica exhibited excellent compressive strength properties with increasing replacement ratio, but fumed silica, unlike micro white, obtained excellent compressive strength at replacement ratio of 0.01~0.1 %. The same trend was observed in the hydration characterization.

• Steel and Composite Structures
• /
• v.52 no.4
• /
• pp.405-418
• /
• 2024

To study the influence of different reduced beam section (RBS) on the mechanical performance of modular boltedwelded hybrid connection joints (MHCJs), this article uses ABAQUS to establish and verify the finite element model (FEM) of the test specimens on the basis of quasi-static test research. Based on, 14 joint models featuring different RBS are devised to evaluate their influence on seismic behavior, such as joint failure mode, bending moment (M)-rotation angle (θ) curve, ductility, and energy consumption. The results indicate that when the flange and web are individually weakened, they alleviate to some extent the concentrated stress of the core module (CM) and column end steel skeleton in the joint core area, but both increase the stress on the flange connecting plate (FCP). At the same time, the impact of both on seismic performance such as bearing capacity, stiffness, and energy consumption is relatively small. When simultaneously weakening the flange and web of the steel beam, forming plastic hinges at the weakened position of the beam end, significantly alleviated the stress concentration of the CM and the damage at the FCP, improving the overall deformation and energy consumption capacity of joints. But as the weakening size of the web increases, the overall bearing capacity of the joint shows a decreasing trend.

• Korean Journal of Environment and Ecology
• /
• v.26 no.5
• /
• pp.707-718
• /
• 2012

This study was conducted to monitor 4 years of changes in the vegetation structure starting from 2007 when restoration began and propose vegetation management ideas for the riparian ecological restoration areas in the purchased land around Nakdonggang(River). The study was conducted in each of 15 locations ($208,342m^2$) in the riparian ecological restoration areas in November 2007, September 2008, October 2009 and September 2010. The analysis results of the changes in planting species and population showed that, in the case of trees, Acer pseudo-sieboldianum, Quercus acutissima, Acer ginnala, Quercus aliena, Quercus variabilis indicated relatively little changes in their numbers and Quercus dentata, Cornus walteri, Morus alba, Styrax obassia, Sorbus alnifolia var. macrophylla indicated a 100% withering rate. Most shrubs withered due to the oppressive pressure of herbs and climbing plants. The planting density decreased over 4 years on average 28 plants/$100m^2$ to 20 plants/$100m^2$ to 16 plants/$100m^2$. Shortly after the restoration, The the amount of growth was reduced by restoration stress. however as time goes on after the restoration tended to stabilize. The changes in the basal area showed a decrease from $507.1cm^2/100m^2$ in 2007 right after restoration to $301.8cm^2/100m^2$ in 2008 and afterwards showed an increasing trend by going to $324.9cm^2/100m^2$ in 2009 and $372.7cm^2/100m^2$ in 2010. To improve the planting structure of the riparian ecological restoration area, the selection of tree species that have been considered for soil moisture and the differentiation of suitable planting structures that have been considered for local conditions were needed.