• Current Photovoltaic Research
• /
• v.1 no.1
• /
• pp.44-51
• /
• 2013

For preparing a device-quality $CuInSe_2$ (CISe) light-absorbing layer by single-bath electrodeposition for a superstrate-type CISe cell, morphological properties of the CISe layers were investigated by varying concentrations of sulfamic acid and potassium biphthalate, complexing/buffering agents. CISe films were grown on an $In_2Se_3$ film by applying a constant voltage of -0.5V versus Ag/AgCl for 90 min in a solution with precursors of $CuCl_2$, $InCl_3$, and $SeO_2$, and a KCl electrolyte. A dense and smooth layer of CISe could be obtained with a solution containing both sulfamic acid and potassium biphthalate in a narrow concentration range of combination. A CISe layer prepared on the $In_2Se_3$ film with proper concentrations of complexing/buffering agents exhibited thickness of $1.6{\sim}1.8{\mu}m$ with few undesirable secondary phases. On the other hand, when the bath solution did not contain either sulfamic acid or potassium biphthalate, a CISe film appeared to contain undesirable flake-shape $Cu_{2-x}Se$ phases or sparse pores in the upper part of film.

• Korean Journal of Chemical Engineering
• /
• v.35 no.12
• /
• pp.2430-2441
• /
• 2018

Selenium (Se)-rich binary Cu-Se and In-Se nanoparticles (NPs) were synthesized by a modified heat-up method at low temperature ($110^{\circ}C$) using the gum exudates from a cherry blossom tree. Coating of CISe absorber layer was carried out using Se-rich binary Cu-Se and In-Se NPs ink without the use of any external binder. Our results indicated that the gum used in the synthesis played beneficial roles such as reducing and capping agent. In addition, the gum also served as a natural binder in the coating of CISe absorber layer. The CISe absorber layer was integrated into the solar cell, which showed a power conversion efficiency (PCE) of 0.37%. The possible reasons for low PCE of the present solar cells and the steps needed for further improvement of PCE were discussed. Although the obtained PCE is low, the present strategy opens a new path for the fabrication of eco-friendly CISe NPs solar cell by a relatively chief non-vacuum method.

• Biomolecules & Therapeutics
• /
• v.13 no.3
• /
• pp.150-155
• /
• 2005

The ethanolic extract of chestnut (Castanea crenata S. et Z., Fagaceae) inner shell (CISE) and one of its components, ellagic acid (EA), were evaluated for their protective effects against 1, 1-diphenyl-2-picryl hydrazine (DPPH) free radical generation and hydrogen peroxide-induced oxidative DNA damage in a mammalian cell line. CISE and EA were shown to possess the free radical scavenging effect against DPPH radical generation, significantly. They were also found to strongly inhibit hydrogen peroxide-induced DNA damage from Chinese hamster lung (CHL) cell, assessed by single cell gel electrophoresis assay and 8-hydroxy -2'-deoxy guanosine (8-OH-2'dG) assay. Furthermore, topical application of CISE [$12.5\%$(w/w) cream] and ellagic acid [$1.0\%$(w/w) cream] for 14 days potently inhibited malondialdehyde (MDA) formation of mouse dorsal skin (a marker of lipid peroxidation) induced by ultraviolet B exposure. Therefore, CISE and its component, ellagic acid, may be the useful natural antioxidants by scavenging free radicals, inhibition of lipid peroxidation and protecting oxidative DNA damage when topically applied.

• Clinics in Shoulder and Elbow
• /
• v.5 no.2
• /
• pp.81-87
• /
• 2002

• Clinics in Shoulder and Elbow
• /
• v.5 no.1
• /
• pp.1-5
• /
• 2002

• Clinics in Shoulder and Elbow
• /
• v.5 no.1
• /
• pp.6-9
• /
• 2002

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.471.2-471.2
• /
• 2014

We demonstrate here that an improvement in precursor film density (green density) leads to a great enhancement in the photovoltaic performance of CuInSe2 (CISe) thin film solar cells fabricated with Cu-In nanoparticle precursor films via chemical solution deposition. A cold-isostatic pressing (CIP) technique was applied to uniformly compress the precursor film over the entire surface (measuring 3~4 cm2) and was found to increase its relative density (particle packing density) by ca. 20%, which resulted in an appreciable improvement in the microstructural features of the sintered CISe film in terms of lower porosity, reduced grain boundaries, and a more uniform surface morphology. The low-bandgap (Eg=1.0 eV) CISe PV devices with the CIP-treated film exhibited greatly enhanced open-circuit voltage (VOC, from 0.265 V to 0.413 V) and fill factor (FF, from 0.34 to 0.55), as compared to the control devices. As a consequence, an almost 3-fold increase in the average power conversion efficiency, 3.0 to 8.2% (with the highest value of 9.02%), was realized without an anti-reflection coating. A diode analysis revealed that the enhanced VOC and FF were essentially attributed to the reduced reverse saturation current density (j0) and diode ideality factor (n). This is associated with the suppressed recombination, likely due to the reduction in recombination sites such as grain/air surfaces (pores), inter-granular interfaces, and defective CISe/CdS junctions in the CIP-treated device. From the temperature dependences of VOC, it was confirmed that the CIP-treated devices suffer less from interface recombination.

• Current Photovoltaic Research
• /
• v.8 no.2
• /
• pp.45-49
• /
• 2020

Molybdenum (Mo) thin films are widely used as back contact in copper indium diselenide (CISe) solar cells. However, despite this, there are only few published studies on the properties of Mo and characteristics of CISe solar cells formed on such Mo substrates. In this studies, we investigated the properties of sputter deposited Mo bilayer, and fabricated non-vacuum CISe solar cells using bilayer Mo substrates. The changes in surface morphology and electrical resistivity were traced by varying the gas pressure during deposition of the bottom Mo layer. In porous surface structure, it was confirmed that the electrical resistivity of Mo bilayer was increased as the amount of oxygen bonded to the Mo atoms increased. The resulting solar cell characteristics vary as the bottom Mo layer deposition pressure, and the maximum solar cell efficiency was achieved when the bottom layer was deposited at 7 mTorr with a thickness of 100 nm and the top layer deposited at 3 mTorr with a thickness of 400 nm.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.257-260
• /
• 2007

In this study, $CuInSe_{2}$ (CISe) and $CuInZnSe_{2}$ (CIZSe) thin films were prepared on Corning 1737 glass by radio frequency (RF) magnetron sputtering from binary chalcogenide mixed powder targets. The targets were initially prepared by mixing appropriate weights of CuSe, InSe powder and various ZnSe contents. From the film bulk analysis result, it is observed that Zn concentration in the films increases proportionally with the addition of ZnSe in the sputtering targets. Under optimized conditions, CISe and CIZSe thin films grow as a chalcopyrite structure with strong (112), (220/204) and (312/116) reflections. Films are found to exhibit a high absorption coefficient of $10^{4}$ $cm^{-1}$. An increasing of optical band gap from 1.0 eV (CISe) to 1.25 eV (CIZSe) is found to be proportional with an increasing of Zn concentration as expected. All films have a p-type semiconductor characteristic with a carrier concentration in the order of 1014 $cm^{-3}$, a mobility about $10^{1}$ $cm^{2{\cdot}-1}{\cdot}s^{-1}$ and a resistivity at the range of $10^{2}-10^{6}$ W${\cdot}$m.

• Clinics in Shoulder and Elbow
• /
• v.21 no.2
• /
• pp.57-58
• /
• 2018